Engineering Papers⌕ Search

Engineering topics

Neyerlin, Kenneth C.

Publications and source records attributed to Neyerlin, Kenneth C..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells

Electrode cracks in polymer electrolyte membrane fuel cells (PEMFCs) are correlated with early onset failures. Here, in this work we investigate the influence of cracked gas diffusion electrodes (GDEs) on the durability of the membrane electrode assembly (MEA) using a combined chemical-mechanical accelerated stress test (AST). Electrode crack dimensions were systematically tuned using ink formulations and material selection strategies. A parameter to describe the crack width areal density (Φ CW ) was used to quantify the degree of discontinuity in the electrode surfaces. Open circuit voltage (OCV) transient analyses were used to benchmark and characterize the failure mechanisms in the MEAs as a function of the Φ CW . While smaller electrode-level cracks, on the order of microns, yielded a 28 % decrease in operating lifetime, larger cracks that propagated from a discontinuous, microporous layer (MPL) coating, decreased the operating lifetime by 56 %. This work emphasizes the need for material processing strategies that consider defect tolerances to limit membrane failures in PEMFCs.

08 HYDROGEN↗
DOE OSTI2024

Mitigation and Diagnosis of Pin-Hole Formation in Polymer Electrolyte Membrane Fuel Cells

In this work, we implement a calendering technique to flatten stray fibers within the gas diffusion media, thereby mitigating pin-hole formation in the hot-pressed MEAs. We have investigated the influence of calendering on the long-term durability for several types of gas diffusion electrodes (GDEs) using a combined chemical and mechanical accelerated stress test (AST). The calendered MEAs demonstrate an average AST lifetime improvement of 77% relative to the as-fabricated MEAs.

AMR↗
DOE OSTI2023

Formate as an Energy Source to Allow Sugar Fermentation with No Net CO2 Generation: Integration of Electrochemistry with Fermentation

This poster summarizes at a high-level the scope of various groups' work on Formate as an Energy Source to Allow Sugar Fermentation with No Net CO2 Generation: Integration of Electrochemistry with Fermentation. The goals of this research are to develop and demonstrate an integrated process that electrochemically generates formate from CO2 and use the formate as an energy source for the fermentation of sugars to fatty acid methyl esters (FAME) without net CO2 generation wherein formate provides reducing equivalents for sugar fermentation and a chemical looping reactor system takes advantage of intermittent low-cost electricity from wind and solar resources.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗
DOE OSTI2022

Elucidating the impact of the ionomer equivalent weight on a platinum group metal-free PEMFC cathode via oxygen limiting current

Leveraging the interactions between ionomer and catalyst can increase the performance of proton exchange membrane fuel cells. The impacts of the equivalent weight (EW) of perfluorosulfonic acid–based ionomers on the platinum group metal-free electrode structure and fuel cell performance have not been fully explored. Four membrane electrode assemblies (MEAs) were prepared by using a commercial Fe–N–C catalyst, two perfluorosulfonic acid ionomers with different EWs, that is, Aquivion 720 (A720) and Nafion 1100 (N1100), and two ionomer-to-catalyst (I/C) ratios. The four MEAs were characterized to understand the impact of the ionomer EW and content on the capacitance, proton conductivity, and mass transport on the cathode. The mass transport resistance was measured for the first time using a new oxygen reduction reaction limiting current method enabling to couple the effects of oxygen diffusion with liquid water generation. Low EW ionomer combined with a moderate I/C results in improved performance due to its enhanced proton conductivity. However, when used at high I/C, it can cause severe water flooding at high current density due to the enhanced liquid water uptake, especially at high relative humidity, resulting in lower catalyst utilization and higher mass transport resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Design of Graded Cathode Catalyst Layers with Various Ionomers for Fuel Cell Application

Proton exchange membrane fuel cells (PEMFCs) powered by green hydrogen (H2) have become a promising alternative to conventional hydrocarbon-fueled power generators. Despite technological advancements, further improvements in efficiency, durability, and low-cost production are required for the widespread adoption of PEMFCs. Though numerous approaches to improve PEMFC electrodes have been reported, most strategies utilize a single material set (e.g., one combination of catalyst and ionomer) to improve performance. Alternatively, anisotropic (graded) electrode structures with locally tunable properties may yield superior electrode performance due to improved ionic and gas phase transport. In this work, graded cathode catalyst layers (CCLs) incorporating different ionomers (Nafion D2020, Aquivion D79-25BS, and HOPI) were designed and prepared. Performance screening shows that some of these graded electrode structures have comparable performance to optimized single-ionomer electrode structures (D2020) suggesting some synergistic benefit. Additionally, we show that electrodes with lower equivalent weight (EW) D79 ionomer near the membrane and D2020 ionomer near the gas diffusion media outperformed electrodes with the inverted configuration. Finally, EIS analysis shows some graded ionomer structures (e.g. D79/D2020) have better than expected H+ conductivity, generally leading to better electrode performance. However, further optimization of ionomer content and catalyst ink formulations is needed to improve overall PEMFC performance.

DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Impact of Platinum Primary Particle Loading on Fuel Cell Performance: Insights from Catalyst/Ionomer Ink Interactions

A variety of electrochemical energy conversion technologies, including fuel cells, rely on solution-processing techniques (via inks) to form their catalyst layers (CLs). The CLs are heterogeneous structures, often with uneven ion-conducting polymer (ionomer) coverage and underutilized catalysts. Various platinum-supported-on-carbon colloidal catalyst particles are used, but little is known about how or why changing the primary particle loading (PPL, or the weight fraction of platinum of the carbon-platinum catalyst particles) impacts performance. Here, by investigating the CL gas-transport resistance and zeta-potentials of the corresponding inks as a function of PPL, a direct correlation between the CL high current density performance and ink zeta-potential is observed. This correlation stems from likely changes in ionomer distributions and catalyst-particle agglomeration as a function of PPL, as revealed by pH, zeta-potential, and impedance measurements. These findings are critical to unraveling the ionomer distribution heterogeneity in ink-based CLs and enabling enhanced Pt utilization and improved device performance for fuel cells and related electrochemical devices.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Proton Conducting Sulfonated Poly(Ionic Liquid) Block Copolymers

Herein, we report the synthesis of proton-conducting sulfonated poly(ionic liquid) block copolymers (S-PILBCPs) containing one block with sulfonic acid (sulfonated styrene, SS) and the other with an IL moiety (vinylbenzylmethylimidazolium bis(trifluoromethylsulfonyl)imide, VBMIm-TFSI) using reversible addition–fragmentation chain-transfer (RAFT) polymerization and post-polymerization modifications (i.e., functionalization, anion exchange reactions, and sulfonation). The S-PILBCPs uniquely conjoin the SS block with mobile protons (H + ) and the PIL block with mobile anions (TFSI – ), where multiple highly desired properties, including high proton conductivity (from the SS block), and high IL-philicity and oxygen solubility (from the PIL block) can exist compartmentally within a microphase separated morphology (evidenced by differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS)). High ion conductivity of 79.7 mS/cm at a PIL block composition of 21.6 mol % was observed at 80 °C and 90% relative humidity (RH) (comparable to the benchmark Nafion ionomer). This work successfully demonstrates the design of S-PILBCPs as a new material platform and showcases its promise as an ionomer for proton exchange membrane fuel cells (PEMFCs) as they simultaneously and compartmentally combine proton conductivity and oxygen solubility. Furthermore, these benefits have recently been leveraged to achieve substantial improvement in oxygen reduction reaction (ORR) activity and subsequently fuel cell performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High current density electroreduction of CO 2 into formate with tin oxide nanospheres

In this study, we demonstrate three-dimensional (3D) hollow nanosphere electrocatalysts for CO 2 conversion into formate with excellent H-Cell performance and industrially-relevant current density in a 25 cm 2 membrane electrode assembly electrolyzer device. Varying calcination temperature maximized formate production via optimizing the crystallinity and particle size of the constituent SnO 2 nanoparticles. The best performing SnO 2 nanosphere catalysts contained ~ 7.5 nm nanocrystals and produced 71–81% formate Faradaic efficiency (FE) between -0.9 V and -1.3 V vs. the reversible hydrogen electrode (RHE) at a maximum formate partial current density of 73 ± 2 mA cm geo -2 at -1.3 V vs. RHE. The higher performance of nanosphere catalysts over SnO 2 nanoparticles and commercially-available catalyst could be ascribed to their initial structure providing higher electrochemical surface area and preventing extensive nanocrystal growth during CO 2 reduction. Our results are among the highest performance reported for SnO 2 electrocatalysts in aqueous H-cells. We observed an average 68 ± 8% FE over 35 h of operation with multiple on/off cycles. In situ Raman and time-dependent X-ray diffraction measurements identified metallic Sn as electrocatalytic active sites during long-term operation. Further evaluation in a 25 cm 2 electrolyzer cell demonstrated impressive performance with a sustained current density of 500 mA cm geo -2 and an average 75 ± 6% formate FE over 24 h of operation. Our results provide additional design concepts for boosting the performance of formate-producing catalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Standardized protocols for evaluating platinum group metal-free oxygen reduction reaction electrocatalysts in polymer electrolyte fuel cells

Platinum group metal (PGM)-free electrocatalysts for the oxygen reduction reaction at the polymer electrolyte fuel cell cathode have shown substantial improvements in activity—especially those derived from transition metals, nitrogen and carbon. However, their stability and durability remain insufficient. A key to enabling future improvements and performance comparisons lies in the development of test protocols that are relevant to the operating conditions of the fuel cell cathode, can be completed within a reasonable time and are ubiquitously adopted. Here we propose and validate such protocols, designed with special attention to typical catalyst degradation mechanisms of PGM-free catalysts. The results of the cross-laboratory validation study using two different catalysts attest to the strength and feasibility of the proposed approach. We hope that the information provided here can serve as a broad and effective platform for assessing the performance and durability of PGM-free catalysts for polymer electrolyte fuel cells.

25 ENERGY STORAGE↗
DOE OSTI2022

An economic analysis of the role of materials, system engineering, and performance in electrochemical carbon dioxide conversion to formate

The development of technologies that utilize carbon dioxide is important to mitigating climate change. The electrochemical reduction of carbon dioxide is one technology that can utilize greenhouse gasses that would be otherwise be emitted to the atmosphere by producing chemicals and fuels from carbon dioxide and electricity. Significant progress has been made in the experimental performance of carbon dioxide reduction systems with novel catalyst designs, new materials, and systems engineering; however, no work has linked such changes in stack design and materials to capital costs for the stack itself. In this study, we present an analysis that accounts for and analyzes the impacts of alternative materials and system architectures on manufactured costs of carbon dioxide reduction stacks, thus providing a framework to understand exactly how these advances impact the at-scale capital costs of these systems. Specifically, we consider the impact that the addition of a catholyte buffer layer has on an electrolyzer reducing carbon dioxide to formate, finding that the cost of manufacturing this part only increases stack costs by about $30/m 2 at high manufacturing rates, while previous work finds that this part improves system performance. This work shows that the links between system performance, materials, and costs are nonlinear, and that achieving low-cost scalability requires optimization of not just performance parameters but also the use of low-cost and highly scalable materials. These results bridge experimental and techno-economic analysis of processes for carbon dioxide reduction, informing researchers by providing a quantifiable estimate of the impact of advances in electrochemical carbon dioxide reduction technology on manufactured stack capital costs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗