Engineering topics

Newman, Alexandra

Publications and source records attributed to Newman, Alexandra.

15 records

DOE OSTI2024

Decomposing a renewable energy design and dispatch model

We address a mixed-integer linear programming model which selects a cost-minimizing set of available technologies with which to design a renewable energy system and prescribe their associated dispatch decisions. Realistically sized instances of such models pose computational challenges. To this end, we develop a Lagrangian heuristic based on a decomposition methodology which partitions the model into blocks and optimizes these more manageable, smaller subproblems. It also provides a lower bound to assess solution quality. In conclusion, we apply this methodology to the National Renewable Energy Laboratory's Renewable Energy Integration and Optimization (REopt TM ) model to generate near-optimal solutions to realistic instances containing, on average, approximately 300,000 variables and at least as many constraints, with a mean 30% optimality gap improvement using a five-minute solution time limit, compared to directly solving the original monolith.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

Characterizing and improving the performance of molten-salt-steam heat exchangers in concentrating solar power plants

Shell-and-tube heat exchangers (HXs) for steam generation from molten salts in concentrating solar power (CSP) plants experience thermal fatigue due to significant temperature gradients and inherent transient operation. Molten salt-steam HX design lifespans exceed actual lifespans, and, as a consequence, designers overpredict plant profitability and operators neglect appropriate prescriptions to optimize these lifetimes. Here, this study refines HX lifespan estimates with data benchmarked against thermal-fluid mechanical modeling of stress and accumulated fatigue. Reduced-order thermal models of the molten salt-steam, shell-and-tube evaporator and superheater predict transient temperature profiles along the two HXs salt-steam flow paths. The modeled evaporator and superheater temperature profiles enable assessment of cyclic stresses within the HX tubesheets, where molten-salt HX failures are most common. Evaporator and superheater performance data from a current 110 MW elec commercial CSP plant provide a basis for validating the reduced-order HX models. HX life predictions derived from stochastic failure distributions serve as inputs for simulating and optimizing existing plant operations. The impact of the updated lifespans on overall plant revenue depends on operating scenarios. This study suggests that typical ramping rates for a CSP plant with a high-temperature Rankine cycle result in an evaporator and superheater life of approximately 10 and 25 years, respectively, compared to the design target of 30 years. Reduced HX lifespans decrease operational plant revenue on average by 4.6-5.1%. Furthermore, there may be as many as four HX replacements over the 30-year lifetime of the plant; and, purchase agreement loss due to failure to meet contractual production requirements can have ramifications that include the risk of bankruptcy.

14 SOLAR ENERGY↗

DOE OSTI2023

Optimizing design and dispatch of a resilient renewable energy microgrid for a South African hospital

Lack of access to reliable energy is a major concern for countries in sub-Saharan Africa. The national grids are unable to consistently satisfy demand. Therefore, users turn to distributed generation systems in the form of back-up generators. However, such systems are usually designed based on a rule of thumb. We employ a mixed-integer linear programming model that considers several options such as renewable energy, combined heat and power, and storage technologies, in addition to those on-site, to provide optimal design and dispatch decisions that minimize total cost. We apply this model to a case study for a hospital in South Africa, considering its need for reliable electricity in light of multiple outages that might occur over the course of a year, as well as its high heating and cooling loads. Our results show that optimal design and dispatch decisions for the distributed generation system address reliability challenges, regardless of the time at which they occur. And, these solutions yield millions of dollars in savings, suggesting that technologies such as the absorption chiller may be overlooked in typical designs; its integration can reduce demand charges even in the absence of combined heat and power. We show that total cost is most sensitive to changes in site electrical demand, followed by capital cost, fuel cost, photovoltaic production, and monthly demand charges; changes in fuel cost primarily affect system sizes of combined heat and power and the absorption chiller, while photovoltaic system size is more sensitive to the changes in capital and fuel costs, photovoltaic resource availability, and hourly electrical demand. Finally, an outage simulator demonstrates the ability of our optimized system to sustain with no interruptions in power five-hour outages with probability 1.0 and ten-hour outages with probability 0.65, significant improvements over 0.5 and 0.0, respectively, under a business-as-usual case.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2023

Improving Mathematical Exposition of an Industrial-Scale Linear Program

Industrial-scale models require considerable setup time; hence, once built, they are used in myriad ways to consider closely related cases. In practice, the code for these models frequently evolves without appropriate notational choices, largely as a result of the lengthy development time of, and the number of individuals contributing to, their formulation. This leads to inefficiencies and obfuscates model structures that might be leveraged to expedite solutions. In this paper, we advocate for an emerging literature on model formulation “best practices” and present the reformulation of a widely used industrial-scale linear program. The efficient mathematical expression of this linear program, used to plan capacity expansion in the energy sector, allows for greater transparency of model structures and enhanced ability to identify computational performance improvements, as well as a lucid interpretation of its solutions. This type of formulation is employed in several mathematical programming courses at our university as an example of the advantages of best practices; the model more broadly is used widely to inform policy in the U.S. energy sector.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2022

North Carolina Water Utility Builds Resilience with Distributed Energy Resources

As the frequency and duration of grid outages increase, backup power systems are becoming more important for ensuring that critical infrastructure continues to provide essential services. Most facilities rely on diesel generators, which may be ineffective during long outages owing to limited fuel supplies and high generator failure rates. Distributed energy resources such as solar, storage, and combined-heat-and-power systems, coupled with on-site biofuel production, offer an alternative source of on-site generation that can provide both cost savings and resilience (i.e., the ability to respond to catastrophic events with longer-term consequences). A mixed-integer linear program minimizes costs and maximizes resilience at a wastewater treatment plant in Wilmington, North Carolina. We find that the plant can reduce life-cycle energy costs by 3.1% through the installation of a hybrid combined-heat-and-power, photovoltaic, and storage system. When paired with existing diesel generators, this system can sustain full load for seven days while saving $664,000 over 25 years and reducing diesel fuel use by 48% compared with the diesel-only solution. This analysis informed a decision by the Cape Fear Public Utility Authority to allocate funds for the implementation of a combined-heat-and-power system at the wastewater treatment plant in fiscal year 2023. Finally, the benefits of deploying hybrid combined-heat-and-power technologies and the utilization of on-site biofuel production extend, on a national scale, to thousands of wastewater treatment facilities and other types of critical infrastructure.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2022

Integrating Concentrating Solar Power Technologies into the Hybrid Optimization and Performance Platform (HOPP)

As the world increases renewable energy deployment, there is an increasing interest in hybridizing various generation and storage technologies to maximize net benefit to the developer and/or off-taker. A particularly interesting combination of renewable technologies is concentrating solar power (CSP) with thermal energy storage (TES), photovoltaics (PV), and electrochemical battery energy storage (BESS). Due to the system complexity of CSP technology, it is difficult to evaluate the technological and financial performance of a CSP-PV hybrid system without detailed modeling of annual operations. To address this challenge, we have developed a modeling framework for evaluating the performance and financial viability of CSP systems hybridized with PV and battery technologies. This modeling effort incorporates CSP tower and trough systems into an existing modeling tool recently developed by NREL referred to as the Hybrid Optimization and Performance Platform (HOPP). This report outlines the modeling methodology as well as preliminary results from example case studies conducted using the model. The methodology describes: (i) the integration of CSP tower and troughs into HOPP using python interfaces to access System Advisor Model (SAM) underlining technology models, (ii) the mathematical formulation of the mixed integer linear program dispatch optimization model which optimizes operations of storage asset to either maximize system revenue or minimize operating cost while load following, (iii) the design analysis methods implemented within HOPP, and (iv) simulation clustering for the purposes of reducing computational expense. We exercise the model using a case study of a future scenario where we assume (i) CSP and PV technologies achieve the 2030 cost targets provided by the Solar Energy Technologies Office (SETO), (ii) battery costs reduce to the 2030 mid cost projection presented by NREL. Lastly, (iii) electricity prices for southern California in 2030 are provided by NREL's Cambium database, and (iv) a capacity payment of $150/kW-yr based on the system capacity factor during the to 100 net-load hours.

14 SOLAR ENERGY↗

DOE OSTI2021

Integrating renewable energy into mining operations: Opportunities, challenges, and enabling approaches

Mining is one of the most energy-intensive industries worldwide. It also provides a critical source of raw materials for the manufacturing, transportation, construction, and energy sectors. Demand for raw materials is projected to increase as the world population grows and many low-income economies become middle-income countries. This growth in mineral demand, coupled with falling mineral ore grade, will likely increase the mining industry’s energy demand, used for activities across exploration, extraction, beneficiation and processing, and refining. At the time of this writing, mine operations are – due to their remoteness – dependent on fossil fuels such as diesel, heavy oils, and coal. In principle, mining could use energy recovery, renewable energy, and carbon capture to supplement, replace, or mitigate the impacts of fossil fuel use. However, a combination of renewable-energy technologies would be required. We explore challenges, opportunities, and enabling approaches to integrate renewable energy technologies into mining operations by examining the literature, including academic work, technical reports, and data produced by international agencies. Here, we find that despite numerous opportunities, technical issues still need to be considered, but solutions can tailor renewables to the mining industry. Further research should focus on identifying specific opportunities, technologies, and implementation strategies across the value chain of a variety of minerals with similar operational procedures.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2021

Concurrent Optimization of Capital Cost and Expected O&M

Concentrating solar power (CSP) technologies can utilize heat from concentrated sunlight from a field of tracking mirrors to generate electricity, reform fuel, provide process heat, or augment fossil plant heat sources. Electricity-generating power tower systems focus light from thousands of independent heliostats onto a thermal receiver, which uses the focused light to warm a heat transfer fluid (HTF), typically, a molten nitrate salt. The HTF is then sent to a power generation cycle or diverted into thermal energy storage (TES) for later use. Thermal storage is – in principle – a straightforward proposition. However, optimal utilization of a TES resource is complex and multi-faceted: thermal energy may be dispatched to produce electricity immediately upon first availability, or thermal energy may be reserved for next-day peak periods at risk of filling storage and dumping energy, or a portion of the thermal energy can be reserved to maintain equipment temperatures, reducing power cycle startup time, etc. Many possible dispatch permutations variously emphasize producing peak power, operating through transients, expediting daily startup, etc. The best operation strategy can change day-to-day throughout the year, depending on the weather and market pricing forecasts. The project we describe in this report develops a software package that allows users to explore design optimization, operations decisions, and performance characterization of concentrating solar power tower plants. Users interface with the tool through a scripting language, and results are reported in time series tables, plots, runtime logs, and design outputs. Users choose from a list of variables such as tower height, solar multiple, design-point irradiance, thermal storage size, etc., and specify information about the system using a list of parameters. The software can then optimize the specified variables to reduce the cost of energy produced by the system while meeting certain production requirements, accounting for uncertain weather and electricity price forecasts, and correcting for equipment failures or repair time. The software we develop is the first comprehensive design tool of its kind to incorporate all of these aspects while being deployed as open source.

14 SOLAR ENERGY↗

DOE OSTI2021

Optimizing design and dispatch of a renewable energy system

Renewable energy technologies are becoming increasingly important due to their cost-competitiveness, and because of enhanced climate concerns. We demonstrate the capabilities of an integer-programming optimization model that minimizes capital (investment) and operational costs, and utility charges, while adhering to system sizing constraints, demand requirements, and interoperability characteristics of the systems chosen. Furthermore, the model recommends an optimally sized mix of renewable energy, conventional generation, and energy storage technologies, while simultaneously optimizing the corresponding dispatch strategy. Our case studies explore several venues, i.e., a small campus and a local hospital, with complex utility rate tariffs, multi-technology integration opportunities, and incentives for renewable power production. Using an optimization model, versus applying rules of thumb, can produce millions of dollars in savings over a 25-year time horizon and result in thousands of kilowatts of installed renewable energy.

25 ENERGY STORAGE↗

DOE OSTI2020

Methods for R&D Portfolio Analysis and Evaluation (Workshop Report)

The Workshop on Methods for R&D Portfolio Analysis and Evaluation convened on 17–18 July 2019 at the National Renewable Energy Laboratory in Golden, Colorado, and examined strengths and weaknesses of the various methodologies applicable to R&D portfolio modeling, analysis, and decision support, given pragmatic constraints such as data availability, uncertainties in estimating the impact of R&D spending, and practical operational overheads. Participants employed their deep expertise in approaches such as stochastic optimization, real options, Monte-Carlo analysis, Bayesian networks, decision theory, complex systems analysis, deep uncertainty, and technology-evolution modeling to critique the initial example models developed by the project’s core team and to conduct thought experiments grounded in real-life technology models, progress data, expert elicitation, and portfolio information. This engagement of participants’ methodological expertise with the practical requirements of real-life portfolio decision support yielded ideas for improved approaches, alternative methodological hypotheses, and hybridization of methodologies that are well-grounded theoretically, computationally sound, and realistically executable given data availability and other practical constraints.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Methods for R&D Portfolio Analysis and Evaluation (Workshop Report)

The Workshop on Methods for R&D Portfolio Analysis and Evaluation convened on 17-18 July 2019 at the National Renewable Energy Laboratory in Golden, Colorado, and examined strengths and weaknesses of the various methodologies applicable to R&D portfolio modeling, analysis, and decision support, given pragmatic constraints such as data availability, uncertainties in estimating the impact of R&D spending, and practical operational overheads. Participants employed their deep expertise in approaches such as stochastic optimization, real options, Monte-Carlo analysis, Bayesian networks, decision theory, complex systems analysis, deep uncertainty, and technology-evolution modeling to critique the initial example models developed by the project’s core team and to conduct thought experiments grounded in real-life technology models, progress data, expert elicitation, and portfolio information. This engagement of participants’ methodological expertise with the practical requirements of real-life portfolio decision support yielded ideas for improved approaches, alternative methodological hypotheses, and hybridization of methodologies that are well-grounded theoretically, computationally sound, and realistically executable given data availability and other practical constraints.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2019

Design, Analysis, and Operations Toolkit (DAO-Tk)

The Design, Analysis, and Operations Toolkit (DAO-Tk) is a software package that allows users to explore design optimization, operations decision, and performance characterization of concentrating solar power tower plants. Users interface with the tool through a scripting language, and results are reported in time series tables, plots, runtime logs, and design outputs. Users choose from a list of variables such as tower height, solar multiple, design-point irradiance, thermal storage size, etc., and specify information about the system using a list of parameters. The software can then optimize the specified variables to reduce the cost of energy produced by the system while meeting certain production requirements, accounting for uncertain weather and electricity price forecasts, and correcting for equipment failures or repair time. The DAO-Tk software is the first comprehensive design tool of it's kind to incorporate all of these aspects while being deployed as open source.

Martinek, Janna↗

DOE OSTI2018

Optimizing dispatch for a concentrated solar power tower

Concentrating solar power (CSP) systems employ a sophisticated thermal receiver, power cycle, and a heliostat field, comprised of thousands of mirrors spread over hundreds of acres of land, and are most cost-effective with relatively large quantities of energy storage which can be scheduled for dispatch. We exercise an existing optimization model that maximizes revenue over a year-long time horizon, solved using a standard 48-h look-ahead policy at hourly fidelity on a CSP system under development in California. The system employs molten salt power tower technology with a 150 MWe (net) turbine, eight hours of thermal storage at full load, and a solar field that provides 1.75 times the rated turbine thermal power. The model considers system configuration and interoperability aspects, such as storage tank size, production capacities, and ramp rates, and determines decisions that expedite financing, permitting, and plant design. Relative to results achieved via industry practice, the existing optimization model reduces the number of power cycle (i.e., turbine) start-up events by 86.4%, thereby improving net revenue by more than 8.5% annually; this corresponds to an approximately $140 M increase in net revenue over the lifetime of the plant, taking a step towards advancing the long-term economic viability of large-scale renewable energy systems. Sensitivity analysis on uncertain parameter values provides insight regarding those values that influence profit most significantly.

14 SOLAR ENERGY↗

DOE OSTI2018

Optimizing Nuclear Material Accounting and Measurement Systems

The ability to create nuclear weapons from 235 U and 239 Pu makes it imperative to closely account for these materials as they progress through a nuclear fuel cycle. Improved measurement systems provide more accurate estimates of material quantities and material unaccounted for (MUF). This work provides examples of how two safeguards computational toolboxes can optimize and analyze hypothetical nuclear fuel cycle scenarios. The NUclear Measurement System Optimization (NUMSO) toolbox uses operations research techniques to find optimal solutions to safeguards measurement problems based on minimizing the variance of the estimated MUF. The SafeGuards Analysis (SGA) toolbox employs Monte Carlo techniques to analyze a given configuration of measurement methods and material flows to determine the probabilities of Type I (false detection) and Type II (missed detection) errors. Applying these toolboxes to a realistic fuel cycle scenario demonstrates the capability of NUMSO and SGA to address nuclear safeguards problems. Working in tandem, both toolboxes are able to determine how to quickly improve upon an existing safeguards measurement system and to calculate the resulting improvement in the error probabilities of the system. This information shows engineers not only how to develop new measurement systems but also how to improve existing systems in the most efficient manner.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2018

NUclear Measurement System Optimization

The NUclear Measurement System Optimization (NUMSO) toolbox interfaces with models developed using SGA to provide combined uncertainty and related operations information about the safeguards process. The primary focus of NUMSO is to determine the best locations and operating times for measurement devices to minimize the sum of Type I and Type II errors. A secondary focus is to determine the key contributors to the Type I and Type II errors indicated by SGA. NUMSO can also determine the best devices to recalibrate and the best times to recalibrate those devices given a limited budget.

Johnson, Benjamin↗