Engineering Papers⌕ Search

Engineering topics

Nespoli, F.

Publications and source records attributed to Nespoli, F..

Initial design concepts for solid boron injection in ITER

As part of ITER’s consideration to change its first wall material from beryllium to tungsten, the ITER Organization has proposed studying the feasibility of real-time solid boron injection (SBI) into the plasma to coat the walls and divertor to supplement glow discharge boronization (GDB). Boron deposits getter oxygen and reduce sputtering of tungsten from plasma facing components (PFCs). Particularly in areas with significant plasma wall interactions, boron coatings are expected to be short-lived under high performance plasma conditions. The proposed SBI system aims to maintain boron layers in these areas to avoid excessive radiation from tungsten in the plasma as a risk mitigation to ensure ITER will be able to reach and sustain Q = 10 conditions. The system will be used sparingly, as redeposition of boron can lead to significant tritium retention, which must be minimized in ITER to comply with nuclear safety concerns. SBI is proposed to limit and precisely control the amount of boron injected in real-time during plasma operation. Here, some of the design requirements and initial concepts for an SBI system in ITER are presented based on previous results carried out with SBI systems on a number of tokamaks and stellarators around the world. Previous results using SBI systems installed by PPPL have injected boron particles from 5 µm–2 mm diameter at calibrated rates of 2–200 mg/s in real-time during plasma operation on AUG, DIII-D, EAST, KSTAR, LHD, TFTR, WEST, and W7-X, leading to improved wall conditions with reduced plasma impurity concentrations and radiated power and improved plasma performance. The boron is ionized in the plasma edge and then deposited on plasma-wetted surfaces. On AUG, EAST and WEST reduced tungsten sputtering sources were observed following several discharges with SBI. Extrapolation of these SBI results are presented to estimate the amount of boron needed for wall conditioning in ITER. Real-time SBI control requirements and plasma operation scenarios for ITER are also described.

36 MATERIALS SCIENCE↗

Full-torus impurity transport simulation in boron powder injection experiments in the Large Helical Device

The toroidal distribution of boron deposition on plasma-facing components (PFCs) in boron powder injection using an impurity power dropper (IPD) was investigated by full-torus simulation and observations in a systematic plasma density-scan experiment. The images of the ablation of dropped boron powders observed with a visible CCD camera were consistently explained by the simulations of the ablation positions of the boron powders considering the size distribution. Simulations assuming full-torus boron deposition on the PFCs did not reproduce the observed intensity profile of boron emission lines for higher plasma densities. It indicated that the density of boron deposited on PFCs installed toroidally far from the IPD was low for higher plasma densities due to the change in the ablation positions of the boron powders toward the outboard side. The experimental results verified the previous full-torus simulation of the toroidal distribution of the boron deposition in both lower and higher plasma densities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Compelling Need for a Mid-Scale Stellarator Facility

In the pursuit of the goal of commercial fusion as an abundant and safe source of energy, the stellarator is a leading concept with compelling attractiveness and demonstrated performance. In this white paper we, as a community of US researchers from Universities, National Laboratories, and Private Industry, involved in studying the stellarator concept, lay out the programmatic and technical motivation for a new mid-size stellarator research facility in the US. This contribution is complementary to several other whitepapers authored by members of our community which address different mid-scale stellarator aspects. A community based technical facility proposal has been prepared by F. Parra, et al: Flexible Stellarator Physics Facility. Two private stellarator companies have submitted proposals supporting the development of a mid-scale stellarator: Thea Energy (C.P.S. Swanson, et al.), Type One Energy (W. Guttenfelder, et al.).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Compelling Need for a Mid-Scale Stellarator Facility

In the pursuit of the goal of commercial fusion as an abundant and safe source of energy, the stellarator is a leading concept with compelling attractiveness and demonstrated performance. A new mid-size stellarator is needed to retire risks and innovate towards a high performance, economically attractive, stellarator Fusion Pilot Plant. In this presentation we, as a community of US researchers from Universities, National Laboratories, and Private Industry, involved in studying the stellarator concept, lay out the programmatic and technical motivation for a new and modern mid-size stellarator research facility. A new mid-scale stellarator is needed to realize the potential predicted by a solid body of theory and simulation along with advances in computational tools for optimization and non-linear turbulence modeling. Notably, it is possible to combine the advantages of the stellarator (steady state, no current drive, no disruptions) with the good confinement regularly achieved in tokamaks. The top priorities for experimental work, and the motivation for a mid-scale stellarator experiment are: turbulence control, non-resonant divertor, MHD stability at large beta, confinement of fast particles, and coil simplification. A new mid-size quasi-symmetric stellarator, built as a user facility, would complement existing research at Wendelstein 7-X and LHD and strongly augment private industry. It would provide a program of innovative research, concept validation, theoretical advancement, and workforce development. Growing support and interest for stellarators by the fusion community and private industry affirms this rationale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Self‐consistent transport simulation of boron dust particle injection in the peripheral plasma in Large Helical Device

Abstract The trajectories and the ablation positions of boron dust particles dropped from an impurity powder dropper in the peripheral plasma in the Large Helical Device (LHD) were calculated using a three‐dimensional edge plasma simulation code (EMC3‐EIRENE) and a dust transport simulation code (DUSTT). The simulation shows that the trajectory of the boron dust particles is deflected at the upper divertor leg due to the effect of the hydrogen plasma flow, and the ablation positions of the dust particles in an ergodic layer change toward the outboard side of the torus for higher plasma densities. The effect of the boron ion flow in the divertor leg on the deflection is investigated by coupling the two codes self‐consistently. The simulation predicts that the boron ions in the divertor leg, which are produced by sputtering on the divertor plates, which do not affect the change in the ablation positions. It also shows that the ablation positions move toward the inboard side and approach the Last Closed Flux Surface (LCFS) in case of increased boron dust drop rates, which is caused by the lowered plasma flow in the upper divertor leg due to the lowered electron temperature by radiation cooling by the dropped dust particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterization of injection and confinement improvement through impurity induced profile modifications on the Wendelstein 7-X stellarator

Pulsed injections of boron carbide granules into Wendelstein 7-X stellarator (W7-X) plasmas transiently increase the plasma stored energy and core ion temperatures above the reference W7-X experimental programs by up to 30%. In a series of 4 MW electron cyclotron resonance heating experiments, the PPPL Probe Mounted Powder Injector provided 50 ms bursts of 100 μm granules every 350 ms at estimated quantities ranging from approximately 1 mg/pulse to over 30 mg/pulse. For each injection, the stored energy was observed to initially drop and the radiated power transiently increased, while the radial electron density profile rose at the edge as material was assimilated. Once the injected boron carbide was fully absorbed, the density rise transitioned to the core while the stored energy increased above the previous baseline level by an amount linearly correlated with the injection quantity. During the injection, the ion temperature gradient steepened with peak core ion temperatures observed to increase from a nominal 1.7 keV to over 2.6 keV for the largest injection amounts. Enhanced performance is accompanied by a reversal of the radial electric field at ρ < 0.3, indicating that the core transport has switched to the ion root. These observations are suggestive of a change in transport and provide further evidence that externally induced profile modifications provide a possible path to enhanced W7-X performance metrics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hyperdiffusion of dust particles in a turbulent tokamak plasma

In this work, the effect of plasma turbulence on the trajectories of dust particles is investigated for the first time. The dynamics of dust particles is computed using the ad hoc developed Dust Injection Simulator code, using a 3D turbulent plasma background computed with the TOKAM3X code. As a result, the evolution of the particle trajectories is governed by the ion drag force, and the shape of the trajectory is set by the Stokes number St∝a d /n 0 , with a d the dust radius and n 0 the density at the separatrix. The plasma turbulence is observed to scatter the dust particles, exhibiting a hyperdiffusive regime in all cases. The amplitude of the turbulent spread of the trajectories Δr 2 is shown to depend on the ratio Ku/St, with Ku∝u rms the Kubo number and urms the fluctuation level of the plasma flow. These results are compared with a simple analytical model, predicting Δr 2 ∝(Ku/St) 2 t 3 , or Δr 2 ∝(u rms n 0 /a d ) 2 t 3 . As the dust is heated by the plasma fluxes, thermionic emission sets the dust charge, originally negative, to slightly positive values. This results in a substantial reduction of the ion drag force through the suppression of its Coulomb scattering component. The dust grain inertia is then no longer negligible and drives the transition from a hyperdiffusive regime toward a ballistic one.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of collisionality on turbulence in the edge of tokamak plasma using 3D global simulations

Collisionality is one of the key parameters in determining turbulent transport in the plasma edge, regulating phenomena such as 'shoulder formation', separation of scale lengths in the scrape-off layer (SOL), turbulence damping and zonal flow dynamics. Understanding its role is therefore of primary importance for future reactors like ITER. Getting reliable predictions and a better characterization of plasma flow properties when varying collisionality remains, however, a critical challenge for the simulations. This paper focuses on the impact of varying collisionality in a non-isothermal three-dimensional fluid model of the plasma edge. A high field side limited configuration encompassing open and closed magnetic field lines with parameters typical of a medium-sized tokamak is considered. The present model can consistently account for the variations of collisionality and its impact on both the parallel resistivity η ∥ and the ion and electron parallel thermal conductivities χ ∥e,i . Details on mean flow and turbulence properties are given. Changing collisionality leads to significant changes in the flow properties both on the mean and fluctuating quantities. In particular, lowering collisionality decreases the size of coherent structures, the fluctuation levels of turbulence, and steepens the density and temperature equilibrium profiles around the separatrix leading to a global reduction of the turbulent transport. The SOL width is observed to increase with collisionality, eventually resulting in the disappearance of the scale lengths separation between near and far SOL, consistently with previous experimental observations. At low collisionality, where the presence of narrow feature is well-established, a contribution of heat conduction increases up to compete with heat convection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First modeling of strongly radiating WEST plasmas with SOLEDGE-EIRENE

We present first results of SOLEDGE-EIRENE modeling a strongly radiating plasma in the WEST tokamak. Using measurements from a reciprocating Langmuir probe we have determined the SOLEDGE input parameters, i.e. separatrix density at outboard midplane and radial transport coefficients typical of L-mode plasma. We have performed deuterium plasma simulations with presence of oxygen, injected from the core boundary into the simulation domain. The comparison between the radiated power measured from the bolometry in the divertor region and the one computed from SOLEDGE simulations seems to indicate a concentration of oxygen of about 2%. Moreover we have obtained good agreement between simulation results and experimental measurements on electron density and electron temperature profiles at the outer strike point. First qualitative analysis of spectroscopic synthetic diagnostic on D α signals is also presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Filamentary velocity scaling validation in the TCV tokamak

A large database of reciprocating probe data from the edge plasma of TCV (Tokamak à Configuration Variable) is used to test the radial velocity scalings of filaments from analytical theory. The measured velocities are mainly scattered between zero and a maximum velocity which varies as a function of size and collisionality in agreement with the analytical scalings. The scatter is consistent with mechanisms that tend to slow the velocity of individual filaments. While the radial velocities were mainly clustered between 0.5 and 2 km/s, a minority reached outward velocities as high as 5 km/s or inward velocities as high as –4 km/s. Inward moving filaments are only observed in regions of high poloidal velocity shear in discharges with B × ∇B away from the X-point, a new finding. Here, the filaments have diameters clustered between 3 and 11 mm, and normalized sizes $\hat{a}$ clustered between 0.3 and 1.1, such that most filaments populate the resistive-ballooning regime; therefore, most of the filaments in TCV have radial velocities with little or no dependence on collisionality. Improvements in cross-correlation techniques and conditional averaging techniques are discussed which reduce the sizes determined for the largest filaments, including those larger than the scrape-off layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impurity seeding for suppression of the near scrape-off layer heat flux feature in tokamak limited plasmas

In inboard-limited plasmas, foreseen to be used in future fusion reactor start-up and ramp down phases, the Scrape-Off Layer (SOL) exhibits two regions: the “near” and “far” SOL. The steep radial gradient of the parallel heat flux associated with the near SOL can result in excessive thermal loads onto the solid surfaces, damaging them and/or limiting the operational space of a fusion reactor. In this article, leveraging the results presented in the study by F. Nespoli et al . [Nucl. Fusion 57, 126029 (2017)], we propose a technique for the mitigation and suppression of the near SOL heat flux feature by impurity seeding. Here, the first successful experimental results from the TCV tokamak are presented and discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Poloidal asymmetry in the narrow heat flux feature in the TCV scrape-off layer

Heat flux profiles inferred from a reciprocating probe at the outer midplane of the TCV tokamak during inner wall limited discharges feature radial fall-off lengths that shorten near the last closed flux surface (LCFS) consistent with the so-called narrow feature. The narrow feature is significantly wider on the outboard side compared with that measured on the inner wall by infrared thermography, so it is difficult to discern from the main scrape-off layer feature. After small shifts were applied for alignment, the fraction of the power contained in the narrow feature matches between inboard and outboard measurements, and they scale together with plasma current Ip, suggesting that we are observing the same phenomenon. The outboard side fall-off length within the narrow feature is found to scale closely with the radial correlation length of the edge turbulence as expected if the narrow feature arises due to radially sheared E x B flows. This is found to hold true even for cases where the narrow feature is weak and the fall-off lengths are approaching that of the far scrape-off layer. After the small shifts for alignment, non-zero floating potential profiles were found to match between inboard and outboard sides. A simple model of polarization and diamagnetic cross-field currents is described, which is consistent with the shape of these floating potential profiles. The model predicts that the floating potential at the LCFS must be negative, which supports the argument to shift the upstream measurements. The predicted currents are also consistent with the E x B flows believed to cause the narrow feature. The model is used to predict the magnitude of the floating potential of the LCFS, and the results are found to match measurements for all values of I p . This paper therefore demonstrates consistency between the measurements of the narrow feature on the inboard and outboard sides of the plasma, as well as consistency between the measurements, non-linear turbulence simulations, and analytical models of the narrow feature arising from sheared E x B flows.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of a narrow limiter SOL heat flux channel on the ITER first wall panel shaping

We report the inboard limiters for ITER were initially designed on the assumption that the parallel heat flux density in the scrape-off layer (SOL) could be approximated by a single exponential with decay length λ q . This assumption was found not to be adequate in 2012, when infra-red (IR) thermography measurements on the inner column during JET limiter discharges clearly revealed the presence of a narrow heat flux channel adjacent to the last closed flux surface. This near-SOL decay occurs with λ q ~ few mm, much shorter than the main SOL λ q , and can raise the heat flux at the limiter apex a factor up to ~4 above the value expected from a single, broader exponential. The original logarithmically shaped ITER inner wall first wall panels (FWPs) would be unsuited to handling the power loads produced by such a narrow feature. A multi-machine study involving the C-Mod, COMPASS, DIII-D and TCV tokamaks, employing inner wall IR measurements and/or inner wall reciprocating probes, was initiated to investigate the narrow limiter SOL heat flux channel. This paper describes the new results which have provided an experimental database for the narrow feature and presents an ITER inner wall FWP toroidal shape optimized for a double-exponential profile with λ q = 4 (narrow feature) and 50 mm (main-SOL), the latter also derived from a separate multi-machine database constituted recently within the International Tokamak Physics Activity. It is shown that the new shape allows the power handling capability of the original shape design to be completely recovered for a wide variety of limiter start-up equilibria in the presence of a narrow feature, even taking assembly tolerances into account. Additionally, it is further shown that the new shape has the interesting property of both mitigating the impact of the narrow feature and resulting in only a very modest increase in heat load, compared to the current design, if the narrow feature is not eventually found on ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗