Engineering topics
Publications and source records attributed to Nelson, R. C..
Attention is given to the flow-visualization problem posed by the 'dark-core' region of the vortices formed on the upper side of a delta wing; the low particle density in the core region minimizes the density of tracing particles whose presence is essential in LDV measurements. An effort is presently undertaken using TiCl4 smoke in subsonic wind tunnel tests of a 70-deg sweep delta wing model.
Explore the source record for details and available documents.
An investigation into the effects of using a jet of air to control the vortex breakdown position on a 70 degree delta wing is presented. The specific objectives focused on optimizing the blowing positions in terms of maximum lift increments obtained for minimum blowing rates. The tests were conducted at chord Reynolds numbers of 150,000, 200,000, and 250,000 at angles of incidence of 30 and 35 degrees. Visualization and force data is presented to show the effect of the jet on the wing aerodynamic characteristics. The results indicate a jet position located at and aligned parallel to the leading edge to be the optimum. Nearness to the apex and tangency to the upper surface were also crucial factors. The influence of the jet on the leading edge vortex structure was examined using laser Doppler anemometry. Velocity surveys through the vortex showed that at high blowing rates the parallel velocity in the outer swirling region of the vortex increased and the normal velocity decreased. This resulted in a decrease in the swirling angle in the outer region. The peak core velocity was reduced and the vortex breakdown was delayed.
A study of the dynamic behavior of the leading edge vortices on a delta wing undergoing oscillatory pitching motion is presented. A sharp edge, flat plate, delta wing having a sweep angle of 70 deg was used in this investigation. The wing was sinusoidally pitched about its 1/2 chord position at reduced frequencies ranging from k = 2(pi)fc/u = 0.05 to 0.30 at chord Reynolds numbers between 90,000 and 350,000, for angle of attack ranges of 29 to 39 deg and 0 to 45 deg. During these dynamic motions, visualization of the leading edge vortices was obtained by marking the vortices with TiCl4 introduced through ports located near the model apex. The location of vortex breakdown was recorded using high speed motion picture photography. The motion picture records were analyzed to determine vortex trajectory and breakdown position as a function of angle of attack. When the wing was sinusoidally pitched, a hysteresis was observed in the location of breakdown position. This hysteresis increased with reduced frequency. The velocity of breakdown propagation along the wing, and the phase lag between model motion and breakdown location were also determined. Detailed information was also obtained on the oscillation of breakdown position in both static and dynamic cases.
An experimental study of the leading edge vortices on delta wings at large angles of incidence is presented. A combination of flow visualization, seven-hole pressure probe surveys and laser velocimeter measurements were used to study the leading edge vortex formation and breakdown for a set of delta wings. The delta wing models were thin flat plates with sharp leading edges having sweep angles of 70, 75, 80, and 85 degrees. The flow structure was examined for angles of incidence from 10 to 40 degrees and chord Reynolds numbers from 85,000 to 640,000. Vortex breakdown was observed on all the wings tested. Both bubble and spiral modes of breakdown were observed. The visualization and wake survey data shows that when vortex breakdown occurs the core flow transforms abruptly from a jet-like flow to a wake-like flow. The result also revealed that probe induced vortex breakdown was more steady than the natural breakdown.
An account is given of the results obtained by a flow visualization study of the roll-up, breakdown position, and spiral- or bubble-type breakdown characteristics of an 85-deg sweep, flat-plate delta wing at large angles-of-attack. The two different breakdown modes were noted to metamorphose into each other, with the bubble-type phenomenon appearing to prefer a more upstream location relative to the spiral mode. In those instances when the breakdown location was changing, the breakdown took the form of a bubble when moving forward, and spiral when moving aft.
An experimental investigation of vortex breakdown on delta wings at high angles is presented. Thin delta wings having sweep angles of 70, 75, 80 and 85 degrees are being studied. Smoke flow visualization and the laser light sheet technique are being used to obtain cross-sectional views of the leading edge vortices as they break down. At low tunnel speeds (as low as 3 m/s) details of the flow, which are usually imperceptible or blurred at higher speeds, can be clearly seen. A combination of lateral and longitudinal cross-sectional views provides information on the three dimensional nature of the vortex structure before, during and after breakdown. Whereas details of the flow are identified in still photographs, the dynamic characteristics of the breakdown process were recorded using high speed movies. Velocity measurements were obtained using a laser Doppler anemometer with the 70 degree delta wing at 30 degrees angle of attack. The measurements show that when breakdown occurs the core flow transforms from a jet-like flow to a wake-like flow.
In the present experimental investigation of thin delta wing vortex breakdown, for the cases of sweep angles of 70, 75, 80, and 85 deg, and smoke flow visualization/laser light sheet technique is used to obtain cross sectional views of the leading edge vortices as they break down. A combination of lateral and longitudinal cross sectional views furnishes data on the three-dimensional character of the vortex before, during, and after breakdown. Velocity measurements conducted with a laser Doppler anemometer on the 70 deg sweep delta, at 30 deg angle-of-attack, indicate that when breakdown occurs the core flow is transformed from a jet-like to a wake-like flow.
Cold working effects on dispersion strengthened nickel alloys containing thorium dioxide
Dispersion strengthened, nickel molybdenum, nonoxidation resistant alloys