Engineering Papers⌕ Search

Engineering topics

Neiner, Doinita

Publications and source records attributed to Neiner, Doinita.

At least 19 records

Blending materials composed of boron, nitrogen and carbon to transform approaches to liquid hydrogen stores

Energy storage remains a key challenge for the advancement of fuel cell applications. Because of this, hydrogen has garnered much research attention for its potential as an energy carrier. This can be attributed to its abundance from non-petroleum sources, and its energy conversion efficiency. Our group, among others, has been studying the use of ammonia borane as a chemical hydrogen storage material for the past several years. Ammonia borane (AB, NH3BH3), a solid state complex composed of the light weight main group elements of nitrogen and boron, is isoelectronic with ethane and as such is an attractive hydrogen storage material with a high gravimetric capacity of H2 (19.6 wt%). However, the widespread use of AB as a chemical hydrogen storage material has been stalled by some undesirable properties and reactivity. Most notably, AB is a solid and this presents compatibility issues with the existing liquid fuel infrastructure. The thermal release of H2 from AB also results in the formation of volatile impurities (borazine and ammonia) that are detrimental to operation of the fuel cell. Additionally, the major products in the spent fuel are polyborazylene and amine borane oligomers that present challenges in regenerating AB. This research was funded by the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy. The Pacific Northwest National Laboratory is operated by Battelle for DOE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Aqueous Binary Lanthanide(III) Nitrate Ln(NO3)3 Electrolytes Revisited: Extended Pitzer and Bromley Treatments

To date, only limited thermodynamic models describing activity coefficients of the aqueous solutions of lanthanide ions are available. This work expands the existing experimental osmotic coefficient data obtained by classical isopiestic technique for the aqueous binary trivalent lanthanide nitrate Ln(NO3)3 solutions using a combination of water activity and vapor pressure osmometry measurements. The combined osmotic coefficient database for each aqueous lanthanide nitrate at 25°C, consisting of literature available data as well as data obtained in this work, was used to test the validity of Pitzer and Bromley thermodynamic models for the accurate prediction of mean molal activity coefficients of the Ln(NO3)3 solutions in wide concentration ranges. The new and improved Pitzer and Bromley parameters were calculated. It was established that the Ln(NO3)3 activity coefficients in the solutions with ionic strength up to 12 mol kg-1 can be estimated by both Pitzer and single-parameter Bromley models, even though the latter provides for more accurate prediction, particularly in the lower ionic strength regime (up to 6 mol kg-1). On the other hand for the concentrated solutions, the extended three-parameter Bromley model can be employed to predict the Ln(NO3)3 activity coefficients with remarkable accuracy. The accuracy of the extended Bromley model in predicting the activity coefficients was greater than ~95% and ~90% for all solutions with the ionic strength up to 12 mol kg-1 and and 20 mol kg-1, respectively. This is the first time that the activity coefficients for concentrated lanthanide solutions have been predicted with such a remarkable accuracy.

Chatterjee, Sayandev↗

Characterization Data Package for Containerized Sludge Samples Collected from Engineered Container SCS-CON-210

This data package contains the K Basin sludge characterization results obtained by Pacific Northwest National Laboratory during processing and analysis of four sludge core samples collected from Engineered Container SCS-CON-210 in 2010 as requested by CH2M Hill Plateau Remediation Company. Sample processing requirements, analytes of interest, detection limits, and quality control sample requirements are defined in the KBC-33786, Rev. 2. The core processing scope included reconstitution of a sludge core sample distributed among four to six 4-L polypropylene bottles into a single container. The reconstituted core sample was then mixed and subsampled to support a variety of characterization activities. Additional core sludge subsamples were combined to prepare a container composite. The container composite was fractionated by wet sieving through a 2,000 micron mesh and a 500-micron mesh sieve. Each sieve fraction was sampled to support a suite of analyses. The core composite analysis scope included density determination, radioisotope analysis, and metals analysis, including the Waste Isolation Pilot Plant Hazardous Waste Facility Permit metals (with the exception of mercury). The container composite analysis included most of the core composite analysis scope plus particle size distribution, particle density, rheology, and crystalline phase identification. A summary of the received samples, core sample reconstitution and subsampling activities, container composite preparation and subsampling activities, physical properties, and analytical results are presented. Supporting data and documentation are provided in the appendices. There were no cases of sample or data loss and all of the available samples and data are reported as required by the Quality Assurance Project Plan/Sampling and Analysis Plan.

core sampling↗

Thermal NF3 fluorination/oxidation of cobalt, yttrium, zirconium, and selected lanthanide oxides

This paper presents results of our continuing investigation on the use of nitrogen trifluoride as a fluorination or fluorination/oxidation agent for separating valuable constituents from used nuclear fuels by exploiting the different volatilities of the constituent fission product and actinide fluorides. This article focuses on fission products that do not have volatile fluorides or oxyfluorides at expected operations temperatures. Our thermodynamic calculations show that nitrogen trifluoride has the potential to completely fluorinate fission product oxides to their fluorides. Simultaneous thermogravimetric and differential thermal analyses show that the oxides of cobalt, zirconium, and the lanthanides are fluorinated but do not form volatile fluorides when treated with nitrogen trifluoride at temperatures up to 550°C. Our studies of gadolinium-doped commercial nuclear fuel indicate that nitrogen trifluoride can extract uranium from the non-volatile gadolinium.

Scheele, Randall D.↗

3-Methyl-1,2-BN-Cyclopentane: A Promising H2 Storage Material?

We provide detailed characterization of properties for 3-methyl-1,2-BN-cyclopentane 1 that are relevant to H2 storage applications such as viscosity, thermal stability, H2 gas stream purity, and polarity. The viscosity of 1 at room temperature is 25±5 cP, about one fourth the viscosity of olive oil. TGA/MS analysis indicates that liquid carrier 1 is thermally stable at 30 °C but decomposes slowly at 50 °C. RGA data suggest that the H2 desorption from 1 is a clean process, producing relatively pure H2 gas. Compound 1 is a polar zwitterionic type liquid consistent with theoretical predictions and solvatochromic studies. "T.A. acknowledges support from the Fuel Cell Technology Program at U.S. DOE, Office of Energy Efficiency 65 and Renewable Energy. Pacific Northwest National Laboratory is operated by Battelle."

Luo, Wei↗

A Thermodynamic and Kenetic Study of the Heterolytic Activation of Hydrogen by Frustrated Borane-Amine Lewis Pairs

Calorimetry is used to measure the reaction enthalpies of hydrogen activation by 2,6-lutidine (Lut), 2,2,6,6-tetramethylpiperidine (TMP), N-methyl-2,2,6,6-tetramethylpiperidine (MeTMP) and tri-tert-butylphosphine (TBP) with tris(pentafluorophenyl)borane (BCF). At 6.6 bar H2 the conversion of the Lewis acid Lewis base pair to the corresponding ionic pair in bromobenzene at 294 K was quantitative in under 60 minutes. Integration of the heat release from the reaction of the Frustrated Lewis Pair (FLP) with hydrogen as a function of time yields a relative rate of hydrogenation in addition to the enthalpy of hydrogenation. The half-lives of hydrogenation range from 230 seconds with TMP, ΔHH2 = -31.5(0.2) kcal/mol, to 1400 seconds with Lut, ΔHH2 = -23.4(0.4) kcal/mol. The 11B NMR spectrum of B(C6F5)3 in bromobenzene exhibits three distinct traits depending on the sterics of the Lewis base; (i) in the presence of pyridine, only the dative bond adduct pyridine--B(C6F5)3 is observed, (ii) in the presence of TMP and MeTMP only the free B(C6F5)3 is observed, and (iii) in the presence of Lut both the free B(C6F5)3 and the Lut--B(C6F5)3 adduct appear in equilibrium. A measure of the change in Keq of Lut + B(C6F5)3 <->Lut--B(C6F5)3 as a function of temperature provides thermodynamic properties of the Lewis acid Lewis base adduct, ΔH = -17.9(1.0) kcal/mol and a ΔS = -49.2(2.5) cal/mol K, suggesting the Lut--B(C6F5)3 adduct is more stable in bromobenzene than in toluene. This research was supported by the U.S. Department of Energy’s Basic Energy Sciences, Division of Chemical Sciences, Biosciences and Geosciences. D.M.C. and A.K. acknowledges support by the Laboratory Directed Research and Development program at the Pacific Northwest National Laboratory (PNNL) to perform kinetic analyses of the calorimetry data. The work was performed in part at EMSL, a national scientific user facility sponsored by the DOE Office of Biological and Environmental Research. EMSL is located at Pacific Northwest National Laboratory (PNNL), which is operated by Battelle for DOE.

calorimetry↗

Single-Pass Flow-Through Test Elucidation of Weathering Behavior and Evaluation of Contaminant Release Models for Hanford Tank Residual Radioactive Waste

Contaminant release models are required to evaluate and predict long-term environmental impacts of even residual amounts of high-level radioactive waste after cleanup and closure of radioactively contaminated sites such as the DOE’s Hanford Site. More realistic and representative models have been developed for release of uranium, technetium, and chromium from Hanford Site tanks C-202, C-203, and C-103 residual wastes using data collected with a single-pass flow-through test (SPFT) method. These revised models indicate that contaminant release concentrations from these residual wastes will be considerably lower than previous estimates based on batch experiments. For uranium, a thermodynamic solubility model provides an effective description of uranium release, which can account for differences in pore fluid chemistry contacting the waste that could occur through time and as a result of different closure scenarios. Under certain circumstances in the SPFT experiments various calcium rich precipitates (calcium phosphates and calcite) form on the surfaces of the waste particles, inhibiting dissolution of the underlying uranium phases in the waste. This behavior was not observed in previous batch experiments. For both technetium and chromium, empirical release models were developed. In the case of technetium, release from all three wastes was modeled using an equilibrium Kd model. For chromium release, a constant concentration model was applied for all three wastes.

chromium↗

Manganese Doping of Magnetic Iron Oxide Nanoparticles: Tailoring Surface Reactivity for a Regenerable Heavy Metal Sorbent

A method for tuning the analyte affinity of magnetic, inorganic nanostructured sorbents for heavy metal contaminants is described. The manganese-doped iron oxide nanoparticle sorbents have a remarkably high affinity compared to the precursor material. Sorbent affinity can be tuned toward an analyte of interest simply by adjustment of the dopant quantity. The results show that following the Mn doping process there is a large increase in affinity and capacity for heavy metals (i.e., Co, Ni, Zn, As, Ag, Cd, Hg, and Tl). Capacity measurements were carried out for the removal of cadmium from river water and showed significantly higher loading than the relevant commercial sorbents tested for comparison. The reduction in Cd concentration from 100 ppb spiked river water to 1 ppb (less than the EPA drinking water limit of 5 ppb for Cd) was achieved following treatment with the Mn-doped iron oxide nanoparticles. The Mn-doped iron oxide nanoparticles were able to load 1 ppm of Cd followed by complete stripping and recovery of the Cd with a mild acid wash. The Cd loading and stripping is shown to be consistent through multiple cycles with no loss of sorbent performance.

36 MATERIALS SCIENCE↗

COMBINING NEUTRAL AND ACIDIC EXTRACTANTS FOR RECOVERING TRANSURANIC ELEMENTS FROM NUCLEAR FUEL

We have been investigating a solvent extraction system that combines a neutral extractant--octyl(phenyl)-N,N-diisobutyl-carbamoylmethylphosphine oxide (CMPO)--with an acidic extractant--bis(2-ethylhexyl)phosphoric acid (HDEHP)--to form a single process solvent for separating Am and Cm from the other components of irradiated nuclear fuel. It was originally hypothesized that the extraction chemistry of CMPO would dominate under conditions of high acidity (> 1 M HNO3), resulting in co-extraction of the transuranic and lanthanide elements into the organic phase. Contacting the loaded solvent with a solution of diethylenetriaminepentaacetate (DTPA) buffered with lactic or citric acid at pH {approx}3 to 4 would result in a condition in which the HDEHP chemistry dominates. Although the data somewhat support this hypothesis, it is clear that there are interactions between the two extractants such that they do not act independently in the extraction and stripping regimes. We report here studies directed at determining the nature and extent of interaction between CMPO and HDEHP, the synergistic behavior of CMPO and HDEHP in the extraction of americium and neodymium, and progress towards determining the thermodynamics of this extraction system. Neodymium and americium behave similarly in the combined solvent system, with a significant synergy between CMPO and HDEHP in the extraction of both of these trivalent elements from lactate-buffered DTPA solutions. In contrast, a much weaker synergistic behaviour is observed for europium. Thus, investigations into the fundamental chemistry involved in this system have focused on the neodymium extraction. The extraction of neodymium has been systematically investigated, individually varying the HDEHP concentration, the CMPO concentration, or the aqueous phase composition. Thermodynamic modeling of the neodymium extraction system has been initiated. Interactions between CMPO and HDEHP in the organic phase must be taken into account in the thermodynamic modeling; such interactions have been quantified by nuclear magnetic resonance measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Kinetic and Thermodynamic Investigation of Hydrogen Release from Ethane 1,2-di-amineborane

The thermodynamics and kinetics of hydrogen (H2) release from ethane 1,2-di-amineborane (EDAB, BH3NH2CH2CH2NH2BH3) were measured using Calvet and differential scanning calorimetry (DSC), pressure-composition isotherms, and volumetric gas-burette experiments. The results presented here indicate that EDAB releases ~ 9 wt.% H2 at temperatures ranging from 100 °C to 200 °C in two moderately exothermic steps, approximately -10±1 kJ/mol H2 and -3.8±1 kJ/mol H2. Isothermal kinetic analysis shows that EDAB is more stable than ammonia borane (AB) at temperatures lower than 100°C; however, the rates of hydrogen release are faster for EDAB than for AB at temperatures higher than 120°C. In addition, no volatile impurities in the H2 released by EDAB were detected by mass spectrometry upon heating with 1°C/min to 200°C in a calorimeter.

08 HYDROGEN↗