Engineering Papers⌕ Search

Engineering topics

Nanda, Jagjit

Publications and source records attributed to Nanda, Jagjit.

At least 127 records · Page 7

Nanostructured Silicon–Carbon 3D Electrode Architectures for High-Performance Lithium-Ion Batteries

Silicon is an attractive anode material for lithium-ion batteries. However, silicon anodes have the issue of volume change, which causes pulverization and subsequently rapid capacity fade. Herein, we report organic binder and conducting diluent-free silicon–carbon 3D electrodes as anodes for lithium-ion batteries, where we replace the conventional copper (Cu) foil current collector with highly conductive carbon fibers (CFs) of 5–10 μm in diameter. We demonstrate here the petroleum pitch (P-pitch) which adequately coat between the CFs and Si-nanoparticles (NPs) between 700 and 1000 °C under argon atmosphere and forms uniform continuous layer of 6–14 nm thick coating along the exterior surfaces of Si-NPs and 3D CFs. The electrodes fabricate at 1000 °C deliver capacities in excess of 2000 mA h g –1 at C/10 and about 1000 mA h g –1 at 5 C rate for 250 cycles in half-cell configuration. Synergistic effect of carbon coating and 3D CF electrode architecture at 1000 °C improve the efficiency of the Si–C composite during long cycling. Full cells using Si–carbon composite electrode and Li 1.2 Ni 0.15 Mn 0.55 Co 0.1 O 2 -based cathode show high open-circuit voltage of >4 V and energy density of >500 W h kg –1 . Replacement of organic binder and copper current collector by high-temperature binder P-pitch and CFs further enhances energy density per unit area of the electrode. It is believed that the study will open a new realm of possibility for the development of Li-ion cell having almost double the energy density of currently available Li-ion batteries that is suitable for electric vehicles.

25 ENERGY STORAGE↗

Synthesis and Electrochemical and Structural Investigations of Oxidatively Stable Li 2 MoO 3 and x Li 2 MoO 3 ·(1 – x )LiMO 2 Composite Cathodes

We report the structural evolution of Li 2 MoO 3 during electrochemical delithiation/lithiation is reported. Li 2 MoO 3 undergoes an irreversible crystalline to amorphous transformation which starts during the first delithiation step and gradually proceeds throughout subsequent cycles. This observation is supported by complementary data obtained from X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). The amorphization does not prevent reversible Li storage, and the Li 2 MoO 3 cathodes exhibit initial capacities of 147 mAh/g (corresponding to 0.87 Li cycled per formula unit) at an average operating potential ~2.5 V vs Li/Li + with reasonably good cycling stability (81% capacity retention after 50 cycles). In-situ mass spectrometry studies reveal the amorphization of Li 2 MoO 3 does not involve the release of oxygen gas even when charged to very positive potentials (i.e., 4.8 V vs Li/Li + ). The Li storage properties and excellent oxidative stability of Li 2 MoO 3 make it a promising candidate to improve the performance of traditional LiMO 2 compounds in layered–layered composite cathodes with the general formula x Li 2 MoO 3 ·(1 – x)LiMO 2 . Multiple synthesis routes were explored to prepare composites with x = 0.10–0.15, and their structure was characterized using XRD and time-of-flight neutron diffraction. Lastly, preliminary characterization of these materials shows that Li 2 MoO 3 improves the cycling stability of an NMC cathode, presumably by mitigating detrimental structural rearrangement at high states of charge.

36 MATERIALS SCIENCE↗

A comparative study on the oxidation of two-dimensional Ti 3 C 2 MXene structures in different environments

The oxidation of two-dimensional Ti 3 C 2 MXene structures has been recognized as a promising method for the formation of hybrid structures of carbon supported nanotitania. Here, we studied the oxidation of Ti 3 C 2 MXene structures using reactive force field (ReaxFF) based molecular dynamics simulations. To investigate the effect of oxidizing agent, we used three different environments including dry air (oxygen molecules), wet air (oxygen and water molecules) and hydrogen peroxide (H 2 O 2 molecules). Oxidation simulations were performed at different temperatures of 1000, 1500, 2000, 2500 and 3000 K. We found that by controlling the temperature, carbon supported titania can be formed by diffusion of Ti atoms to the surface of MXene structures during the oxidation. These results were confirmed by the increase in the average bond orders of C–C and Ti–O and decrease in the average bond orders of Ti–C. Moreover, it was revealed that by increasing the temperature, the oxidation rate increases, and the rate depends on the oxidant according to the following order: H 2 O 2 > wet air > dry air. This was validated by heating the MXene in wet air and dry air followed by examining the products using X-ray diffraction and Raman spectroscopy. To investigate the effect of the presence of the oxidant, the MXene structure was also heated under vacuum, and it was found that in this case the MXene structure was converted to cubic TiC. Furthermore, it was indicated that during the heating process of the MXene structure in a vacuum, the average bond orders for C–C, Ti–C and Ti–O do not change significantly due to the lack of oxidants in the environment, leaving room for only topotactic transformation of atoms during the heating. In conclusion, the formation of the TiC structure by heating the MXene in an inert environment was confirmed experimentally as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanically Robust, Sodium-Ion Conducting Membranes for Nonaqueous Redox Flow Batteries

Sodium-based batteries are promising for grid-storage applications because of significantly lower cost compared to lithium-based systems. The advancement of solid-state and redox-flow sodium-ion batteries requires sodium-ion exchange membranes with high conductivity, electrochemical stability, and mechanical robustness. This study demonstrates that membranes based on poly(ethylene oxide) (PEO) can meet these requirements. Membranes plasticized with tetraethylene glycol dimethyl ether (TEGDME) achieve high ionic conductivity. Plasticized PEO membranes containing sodium triflate salt (NaTFS) show about 2 orders of magnitude higher conductivity compared to nonplasticized PEO membranes. Results from vibrational spectroscopy and differential scanning calorimetry describe the coordination chemistry in these multiphase materials and explain the mechanisms behind the increased conductivity. The mechanical properties of the membranes improve by addition of 5 wt % sodium carboxymethyl cellulose (CMC) without compromising the conductivity or electrochemical stability against sodium metal. In conclusion, the optimized membrane is an excellent candidate for low-cost energy storage systems that operate over a wide voltage window near ambient temperature.

25 ENERGY STORAGE↗

Chemical Evolution in Silicon–Graphite Composite Anodes Investigated by Vibrational Spectroscopy

Silicon–graphite composites are under development for the next generation of high-capacity lithium-ion anodes, and vibrational spectroscopy is a powerful tool to identify the different mechanisms that contribute to performance loss. With alloy anodes, the underlying causes of cell failure are significantly different in half-cells with lithium metal counter electrodes compared to full cells with standard cathodes. However, most studies which take advantage of vibrational spectroscopy have only examined half-cells. In this work, a combination of FTIR and Raman spectroscopy describes several factors that lead to degradation in full pouch cells with LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) cathodes. The spectroscopic signatures evolve after longer term cycling compared to the initial formation cycles. Several side-reactions that consume lithium ions have clear FTIR signatures, and comparison to a library of reference compounds facilitates identification. Raman microspectroscopy combined with mapping shows that the composite anodes are not homogeneous but segregate into graphite-rich and silicon-rich phases. Lithiation does not proceed uniformly either. A basis analysis of Raman maps identifies electrochemically inactive regions of the anodes. In conclusion, the spectroscopic results presented here emphasize the importance of improving electrode processing and SEI stability to enable practical composite anodes with high silicon loadings.

25 ENERGY STORAGE↗

Facile and scalable fabrication of polymer-ceramic composite electrolyte with high ceramic loadings

Solid state electrolytes are a promising alternative to flammable liquid electrolytes for high-energy lithium battery applications. In this work polymer-ceramic composite electrolyte membrane with high ceramic loading (greater than 60 vol%) is fabricated using a model polymer electrolyte poly(ethylene oxide) + lithium trifluoromethane sulfonate and a lithium-conducting ceramic powder. The effects of processing methods, choice of plasticizer and varying composition on ionic conductivity of the composite electrolyte are thoroughly investigated. The physical, structural and thermal properties of the composites are exhaustively characterized. We demonstrate that aqueous spray coating followed by hot pressing is a scalable and inexpensive technique to obtain composite membranes that are amazingly dense and uniform. The ionic conductivity of composites fabricated using this protocol is at least one order of magnitude higher than those made by dry milling and solution casting. The introduction of tetraethylene glycol dimethyl ether further increases the ionic conductivity. The composite electrolyte's interfacial compatibility with metallic lithium and good cyclability is verified by constructing lithium symmetrical cells. As a result, a remarkable Li + transference number of 0.79 is discovered for the composite electrolyte.

36 MATERIALS SCIENCE↗

Probing Electrode-Electrolyte Interfaces Using Nano-Gap Surface-Enhanced Raman Spectroscopy and Imaging

Performance of portable electronic devices and electric vehicles is currently limited by the energy density, lifetime and safety of lithium rechargeable batteries. Overcoming those limitations requires in-depth understanding of the electrode-electrolyte interfaces. Surface-enhanced Raman spectroscopy (SERS) can provide a critical component to this effort as an in situ technique with ultrahigh surface sensitivity that provides quantitative molecular specificity. SERS relies on local electromagnetic field amplification generated by surface plasmon resonance (SPR) at the surface of metal nanoparticles (NPs) with sub-wavelength dimensions. The most significant Raman enhancements have been observed when the local SPRs of multiple NPs interact. This occurs when the NPs are in close proximity (less than 10 nm), which could be achieved in ordered NP monolayers if they could be assembled reproducibly. Methods to assemble gold NPs into large area (cm2) monolayers will be presented. The interparticle gap can be tuned between 1 and 4 nm by using surface ligands of different sizes. The Au NP monolayers exhibit high SERS sensitivity (enhancement factor greater than 107). This allows for the measurement of electrolyte components across a broad range of concentrations. Components include lithium hexafluorophosphate (LiPF6), fluoroethylene carbonate (FEC), ethylene carbonate (EC) and diethyl carbonate (DEC). The investigation of solutions of LiPF6 in EC + DEC binary solvents using SERS allows for the determination of the solvent coordination numbers, which range from 2 to 5. This result is in sharp contrast to the bulk values calculated from infrared spectroscopy, which range from 3 to 7. Numerical simulations show that the electromagnetic field is concentrated in the nanogap, indicating the information of the aprotic electrolyte solution structures is obtained from the immediately adjacent area of the solid substrate. Our findings facilitate a better understanding of the structure of solvated ions in close proximity to the electrode surface.

Yang, Guang↗

Effect of Binder Architecture on the Performance of Silicon/Graphite Composite Anodes for Lithium Ion Batteries

Although significant progress has been made in improving cycling performance of silicon-based electrodes, few studies have been performed on the architecture effect on polymer binder performance for lithium-ion batteries. A systematic study on the relationship between polymer architectures and binder performance is especially useful in designing synthetic polymer binders. In this paper, a graft block copolymer with readily tunable architecture parameters is synthesized and tested as the polymer binder for the high-mass loading silicon (15 wt %)/graphite (73 wt %) composite electrode (active materials >2.5 mg/cm 2 ). With the same chemical composition and functional group ratio, the graft block copolymer reveals improved cycling performance in both capacity retention (495 mAh/g vs 356 mAh/g at 100th cycle) and Coulombic efficiency (90.3% vs 88.1% at first cycle) than the physical mixing of glycol chitosan (GC) and lithium polyacrylate (LiPAA). Galvanostatic results also demonstrate the significant impacts of different architecture parameters of graft copolymers, including grafting density and side chain length, on their ultimate binder performance. Finally, by simply changing the side chain length of GC-g-LiPAA, the retaining delithiation capacity after 100 cycles varies from 347 mAh/g to 495 mAh/g.

25 ENERGY STORAGE↗

Lipon coatings for high voltage and high temperature Li-ion battery cathodes

A lithium ion battery includes an anode and a cathode. The cathode includes a lithium, manganese, nickel, and oxygen containing compound. An electrolyte is disposed between the anode and the cathode. A protective layer is deposited between the cathode and the electrolyte. The protective layer includes pure lithium phosphorus oxynitride and variations that include metal dopants such as Fe, Ti, Ni, V, Cr, Cu, and Co. A method for making a cathode and a method for operating a battery are also disclosed.

25 ENERGY STORAGE↗

Multimodality of Structural, Electrical, and Gravimetric Responses of Intercalated MXenes to Water

Understanding of structural, electrical, and gravimetric peculiarities of water vapor interaction with ion-intercalated MXenes led to design of a multimodal humidity sensor. Neutron scattering coupled to molecular dynamics and ab initio calculations showed that a small amount of hydration results in a significant increase in the spacing between MXene layers in the presence of K and Mg intercalants between the layers. Films of K- and Mg-intercalated MXenes exhibited relative humidity (RH) detection thresholds of ~0.8% RH and showed monotonic RH response in the 0–85% RH range. We found that MXene gravimetric response to water is 10 times faster than their electrical response, suggesting that H 2 O-induced swelling/contraction of channels between MXene sheets results in trapping of H 2 O molecules that act as charge-depleting dopants. Here, the results demonstrate the use of MXenes as humidity sensors and infer potential impact of water on structural and electrical performance of MXene-based devices.

36 MATERIALS SCIENCE↗

Freeze Tape Cast Thick Mo Doped Li 4 Ti 5 O 12 Electrodes for Lithium-Ion Batteries

Lithium titanate (Li 4 Ti 5 O 12 ) powders with and without molybdenum doping (LTO and MoLTO respectively) were synthesized by a solid-state method and used to fabricate electrodes on Cu foil using a normal tape-cast method and a novel freeze-tape-cast method. Modest molybdenum doping produces a significant electronic conductivity increase (e.g. 1 mS cm -1 for MoLTO vs 10 -7 mS cm -1 for LTO) that is thought to reflect a partial Ti 4+ reduction to Ti 3+ with charge compensation by the Mo 6+ dopant, producing a stable mixed-valent Ti 4+/3+ state. Freeze-tape-cast electrodes were fabricated by a variant of the normal tape-cast method that includes a rapid freezing step in which the solvent in the Cu-foil-supported slurry is rapidly frozen on a cold finger then subsequently sublimed to create unidirectional columnar macropores in the electrode. The resulting electrodes exhibit high porosity and low tortuosity which enhances electrolyte accessibility throughout the full electrode thickness. Freeze-tape-cast electrodes subjected to galvanostatic charge-discharge testing as cathodes in cells vs. a lithium metal anode exhibit higher specific capacity and lower capacity loss at high discharge rates compared with normal-tape-cast electrodes of the same mass loading, despite the fact that the freeze-tape-cast electrodes are nearly twice as thick as the normal tape cast electrodes.

25 ENERGY STORAGE↗

Crystal Chemistry and Electrochemistry of Li x Mn 1.5 Ni 0.5 O 4 Solid Solution Cathode Materials

For ordered high-voltage spinel LiMn 1.5 Ni 0.5 O 4 (LMNO) with the P4 3 2 1 symmetry, the two consecutive two-phase transformations at ~4.7 V (vs Li + /Li), involving three cubic phases of LMNO, Li 0.5 Mn 1.5 Ni 0.5 O 4 (L 0.5 MNO), and Mn 1.5 Ni 0.5 O 4 (MNO), have been well-established. Such a mechanism is traditionally associated with poor kinetics due to the slow movement of the phase boundaries and the large mechanical strain resulting from the volume changes among the phases, yet ordered LMNO has been shown to have excellent rate capability. In this paper, we show the ability of the phases to dissolve into each other and determine their solubility limit. We characterized the properties of the formed solid solutions and investigated the role of non-equilibrium single-phase redox processes during the charge and discharge of LMNO. Finally, by using an array of advanced analytical techniques, such as soft and hard X-ray spectroscopy, transmission X-ray microscopy, and neutron/X-ray diffraction, as well as bond valence sum analysis, the present study examines the metastable nature of solid-solution phases and provides new insights in enabling cathode materials that are thermodynamically unstable.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Engineering Redox Potential of Lithium Clusters for Electrode Material in Lithium-Ion Batteries

Low negative electrode potential and high reactivity makes lithium (Li) ideal candidate for obtaining highest possible energy density among other materials. Here, we show a novel route with which the overall electrode potential could significantly be enhanced through selection of cluster size. In using first principles density functional theory and continuum dielectric model, we studied free energy and redox potential as well as investigated relative stability of Li n (n ≤ 8) clusters in both gas phase and solution. We found that Li 3 has the lowest negative redox potential (thereby highest overall electrode potential) suggesting that cluster based approach could provide a novel way of engineering the next generation battery technology. The microscopic origin of Li 3 cluster’s superior performance is related to two major factors: gas phase ionization and difference between solvation free energy for neutral and positive ion. Taken together, our study provides insight into the engineering of redox potential in battery and could stimulate further work in this direction.

25 ENERGY STORAGE↗

Impact of air exposure and surface chemistry on Li-Li 7 La 3 Zr 2 O 12 interfacial resistance

Li 7 La 3 Zr 2 O 12 (LLZO) is a promising solid-state electrolyte that could enable solid-state-batteries (SSB) employing metallic Li anodes. For a SSB to be viable, the stability and charge transfer kinetics at the Li–LLZO interface should foster facile plating and stripping of Li. Contrary to these goals, recent studies have reported high Li–LLZO interfacial resistance which was attributed to a contamination layer that forms upon exposure of LLZO to air. This study clarifies the mechanisms and consequences associated with air exposure of LLZO; additionally, strategies to minimize these effects are described. First-principles calculations reveal that LLZO readily reacts with humid air; the most favorable reaction pathway involves protonation of LLZO and formation of Li2CO3. X-ray photoelectron spectroscopy, scanning electron microscopy, Raman spectroscopy, and transmission electron microscopy were used to characterize the surface and subsurface chemistry of LLZO as a function of relative humidity and exposure time. Additionally, electrochemical impedance spectroscopy was used to measure the Li–LLZO interfacial resistance as a function of surface contamination. These data indicate that air exposure-induced contamination impacts the interfacial resistance significantly, when exposure time exceeds 24 h. The results of this study provide valuable insight into the sensitivity of LLZO to air and how the effects of air contamination can be reversed.

36 MATERIALS SCIENCE↗

Electrochemical performance of MXenes as K-ion battery anodes

In this paper, we report on the electrochemical performance of two-dimensional transition metal carbonitrides as novel promising electrode materials in K-ion batteries. Titanium carbonitride, Ti 3 CNT z , was investigated in detail using electrochemical galvanostatic cycling at various current densities. Finally, X-ray diffraction and X-ray photoelectron spectroscopy were used to study the potassiation mechanism and its structural changes.

25 ENERGY STORAGE↗

Unrivaled combination of surface area and pore volume in micelle-templated carbon for supercapacitor energy storage

Here, we created Immense Surface Area Carbons (ISACs) by a novel heat treatment that stabilized the micelle structure in a biological based precursor prior to high temperature combined activation – pyrolysis. While displaying a morphology akin to that of commercial activated carbon, ISACs contain an unparalleled combination of electrochemically active surface area and pore volume (up to 4051 m 2 g –1 , total pore volume 2.60 cm 3 g –1 , 76% small mesopores). The carbons also possess the benefit of being quite pure (combined O and N: 2.6–4.1 at%), thus allowing for a capacitive response that is primarily EDLC. Tested at commercial mass loadings (~10 mg cm –2 ) ISACs demonstrate exceptional specific capacitance values throughout the entire relevant current density regime, with superior rate capability primarily due to the large fraction of mesopores. In the optimized ISAC, the specific capacitance ( C g ) is 540 F g –1 at 0.2 A g –1 , 409 F g –1 at 1 A g –1 and 226 F g –1 at a very high current density of 300 A g –1 (~0.15 second charge time). At intermediate and high currents, such capacitance values have not been previously reported for any carbon. Tested with a stable 1.8 V window in a 1 M Li 2 SO 4 electrolyte, a symmetric supercapacitor cell yields a flat energy–power profile that is fully competitive with those of organic electrolyte systems: 29 W h kg –1 at 442 W kg –1 and 17 W h kg –1 at 3940 W kg –1 . The cyclability of symmetric ISAC cells is also exceptional due to the minimization of faradaic reactions on the carbon surface, with 80% capacitance retention over 100 000 cycles in 1 M Li 2 SO 4 and 75 000 cycles in 6 M KOH.

25 ENERGY STORAGE↗

High Areal Capacity Si/LiCoO 2 Batteries from Electrospun Composite Fiber Mats

Here, freestanding nanofiber mat Li-ion battery anodes containing Si nanoparticles, carbon black, and poly(acrylic acid) (Si/C/PAA) are prepared using electrospinning. The mats are compacted to a high fiber volume fraction (~0.85), and interfiber contacts are welded by exposing the mat to methanol vapor. A compacted+welded fiber mat anode containing 40 wt % Si exhibits high capacities of 1,484 mA h g -1 (3,500 mA h g$-1\atop{Si}$) at 0.1 C and 489 mAh g -1 at 1 C and good cycling stability (e.g., 73% capacity retention over 50 cycles). Post-mortem analysis of the fiber mats shows that the overall electrode structure is preserved during cycling. Whereas many nanostructured Si anodes are hindered by their low active material loadings and densities, thick, densely packed Si/C/PAA fiber mat anodes reported here have high areal and volumetric capacities (e.g., 4.5 mA h cm -2 and 750 mA h cm -3 , respectively). A full cell containing an electrospun Si/C/PAA anode and electrospun LiCoO 2 -based cathode has a high specific energy density of 270 Wh kg -1 . The excellent performance of the electrospun Si/C/PAA fiber mat anodes is attributed to the: (i) PAA binder which interacts with the SiO x surface of Si nanoparticles and (ii) high material loading, high fiber volume fraction, and welded interfiber contacts of the electrospun mats

25 ENERGY STORAGE↗

Structural Transformations in High-Capacity Li 2 Cu 0.5 Ni 0.5 O 2 Cathodes

Cathode materials that can cycle > 1 Li+ per transition metal are of substantial interest to increase the overall energy density of lithium-ion batteries. Li2Cu0.5Ni0.5O2 has a very high theoretical capacity of ~ 500 mAh/g assuming both Li+ are cycled reversibly. The Cu2+/3+ and Ni2+/3+/4+ redox couples are also at high voltage, which could further boost the energy density of this system. Despite such promise, Li2Cu0.5Ni0.5O2 undergoes irreversible phase changes during charge (delithiation) that result in large first-cycle irreversible loss and poor long-term cycling stability. Oxygen is evolved before the Cu2+/3+ or Ni3+/4+ transitions are accessed. In this contribution, XRD, TEM, and TXM-XANES are used to follow the chemical and structural changes that occur in Li2Cu0.5Ni0.5O2 during electrochemical cycling. Li2Cu0.5Ni0.5O2 is a solid solution of orthorhombic Li2CuO2 and Li2NiO2, but the structural changes more closely mimic the Li2NiO2 endmember. Li2Cu0.5Ni0.5O2 loses long-range order during charge, but TEM analysis provides clear evidence for particle exfoliation and the transformation from orthorhombic to a partially layered structure. Linear combination fitting and principal component analysis of TXM-XANES are used to map the different phases that emerge during cycling ex situ and in situ. Significant changes in the XANES at the Cu and Ni K-edges correlate with the onset of oxygen evolution.

Environmental Molecular Sciences Laboratory↗