Engineering Papers⌕ Search

Engineering topics

Nagy, A.

Publications and source records attributed to Nagy, A..

53 records · Page 3

Fast wave direct electron heating in advanced inductive and ITER baseline scenario discharges in DIII-D

Fast Wave (FW) heating and electron cyclotron heating (ECH) are used in the DIII-D tokamak to study plasmas with low applied torque and dominant electron heating characteristic of burning plasmas. FW heating via direct electron damping has reached the 2.5 MW level in high performance ELMy H-mode plasmas. In Advanced Inductive (AI) plasmas, core FW heating was found to be comparable to that of ECH, consistent with the excellent first-pass absorption of FWs predicted by ray-tracing models at high electron beta. FW heating at the ∼2 MW level to ELMy H-mode discharges in the ITER Baseline Scenario (IBS) showed unexpectedly strong absorption of FW power by injected neutral beam (NB) ions, indicated by significant enhancement of the D-D neutron rate, while the intended absorption on core electrons appeared rather weak. The AI and IBS discharges are compared in an effort to identify the causes of the different response to FWs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Initial Testing of Optical Arc Detector Inside 285/300 Fast Wave Antenna Box on DIII-D

Locating arcs within the fast wave current drive system is necessary to improve antenna performance and coupling to the plasma. Previously, there had been no way to observe arcs inside the vacuum vessel in an ICRF antenna on DIII-D. A new diagnostic that uses photomultiplier tubes has been installed for the 2012 run campaign on the 285/300 antenna of the fast wave system. The diagnostic has top and bottom views of the back of the four antenna straps and uses narrow-bandpass visible filters to isolate emission lines of copper (577 nm) and deuterium (656.1 nm). This diagnostic is based on the ORNL filterscope system currently in use on multiple devices. The system will be used to guide fast wave antenna conditioning, plasma operation and provide insight into future antenna upgrades on DIII-D.

Diem, Stephanie J↗

Fatigue testing of plasma-sprayed thermal barrier coatings, volume 2

A plasma sprayed thermal barrier coating for diesel engines were fatigue tested. Candidate thermal barrier coating materials were fatigue screened and a data base was generated for the selected candidate material. Specimen configurations are given for the bend fatigue tests, along with test setup, specimen preparation, test matrix and procedure, and data analysis.

Cruse, T. A.↗

Mechanical testing of advanced coating system, volume 1

The Electron Beam Physical Vapor Deposition (EBPVD) coating material has a highly columnar microstructure, and as a result it was expected to have very low tensile strength. To be able to fabricate the required compression and tensile specimens, a substrate was required to provide structural integrity for the specimens. Substrate and coating dimensions were adjusted to provide sufficient sensitivity to resolve the projected loads carried by the EBPVD coating. The use of two distinctively different strain transducer systems, for tension and compression loadings, mandated two vastly different specimen geometries. Compression specimen and tensile specimen geometries are given. Both compression and tensile test setups are described. Data reduction mathematical models are given and discussed in detail as is the interpretation of the results. Creep test data is also given and discussed.

Cruse, T. A.↗

High temperature inelastic deformation of the B1900 + Hf alloy under multiaxial loading - Theory and experiment

The multiaxial deformation behavior of the Ni-based alloy B1900 + Hf has been studied at elevated temperatures in the range of 649-982 C. Combined tension/torsion cyclic tests were performed on thin-wall tubular specimens under both in-phase and out-of-phase strain-controlled loading cycles. Both straining conditions resulted in stress loci of comparable magnitude, exhibiting no difference in cyclic hardening response. A phase angle was observed between the deviatoric stress and the incremental plastic strain vectors during 90-deg out-of-phase strain cycling, and nonproportional stress relaxation occurred under biaxial strain hold. The overall results have been used to assess the flow law, the hardening equations, and the applicability of the J2-based, elastic-viscoplastic model of Bodner-Partom (1979) for multiaxial loading conditions. The overall agreement between theory and experiment is good. Discrepancies are discussed in relation to micromechanical considerations.

Chan, K. S.↗

Evaluation of high-contact-ratio spur gears with profile modification

Scoring tests, surface fatigue tests, and single-tooth bending fatigue tests were conducted with four sets of spur gears of standard design and three sets of spur gears of the new tooth form (NTF) design. Scoring tests were conducted in a gear test rig at a speed of 10,000 rpm using a synthetic polyester C5, C6, C7 substituted pentaerythritol oil. Surface fatigue tests were conducted in the same rig at a speed of 10,000 rpm and Hertz stresses of 173 x 10 to the 7th power and 143 x 10 to the 7th power Pa (250,000 and 214,000 psi). Single tooth bending fatigue tests were conducted on both the standard and NTF gears at an initial load that produced a 10.35 x 10 to the eight power Pa (150,000-psi) bending stress. The gears were load cycled to failure or for 3 x 10 to the 6th power cycles, whichever occurred first. The load was increased after test until failure occurred at 3 x 10 to the 6th power cycles or less. Both the standard and NTF gears scored at a gear bulk temperature of approximately 409 K (277 F). At this temperature the load on the NTF gears was 22 percent less than the load on the standard gears. The scoring failure was a function of gear bulk temperature, where for a given lubricant the temperature is a function of gear design, operating load, and speed.

Townsend, D. P.↗

Evaluation of high-contact-ratio spur gears with profile modification

Scoring tests, surface fatigue tests, and single-tooth bending fatigue tests were conducted with four sets of spur gears of standard design and three sets of spur gears of new-tooth-form design. The new-tooth-form and standard gears scored at approximately the same gear bulk temperature of 409 K (277 F). The scoring load for the new-tooth-form gears was 22 percent less than that for the standard gears. The pitting fatigue lives of the standard and new-tooth-form gears were statistically equal for equal Hertz stress, while the surface fatigue life of the nw-tooth-form gears was approximately five times that of the standard gears at the same load. The standard gears failed at a 17 percent higher bending stress than the new-tooth-form gears when stress was calculated by the AGMA method. However, the difference is not statistically significant. The standard gears failed at a tooth load 1.9 times that for the new-tooth-form gears.

Towsend, D. P.↗

Investigation of the composition of the Luna 16 lunar sample

The concentrations of aluminum, manganese, sodium, chromium, iron, cobalt, and 12 rare earth elements were determined by neutron activation analysis using slow neutrons. Oxygen and silicon were determined using a fast neutron generator. Mossbauer spectroscopy was used to investigate iron compounds in Luna 16 regolith samples from the upper part of the core.

Bakos, L.↗

Coupling between structure and liquids in a parallel stage space shuttle design

A study was conducted to determine the influence of liquid propellants on the dynamic loads for space shuttle vehicles. A parallel-stage configuration model was designed and tested to determine the influence of liquid propellants on coupled natural modes. A forty degree-of-freedom analytical model was also developed for predicting these modes. Currently available analytical models were used to represent the liquid contributions, even though coupled longitudinal and lateral motions are present in such a complex structure. Agreement between the results was found in the lower few modes.

Kana, D. D.↗

Deformation mechanics of deep surface flaw cracks

A combined analytical and experimental program was conducted to determine the deformation characteristics of deep surface cracks in Mode I loading. An approximate plane finite element analysis was performed to make a parameter study on the influence of crack depth, crack geometry, and stress level on plastic zones, crack opening displacement, and back surface dimpling in Fe-3Si steel and 2219-T87 aluminum. Surface replication and profiling techniques were used to examine back surface dimple configurations in 2219-T87 aluminum. Interferometry and holography were used to evaluate the potential of various optical techniques to detect small surface dimples on large surface areas.

Francis, P. H.↗

Coupling between structure and liquid propellants in a parallel-stage space shuttle design.

A study was conducted to determine the influence of liquid propellants on the dynamic loads for space shuttle vehicles. A parallel-stage configuration model was designed and tested to determine the influence of liquid propellants on coupled natural modes. A forty degree-of-freedom analytical model was also developed for predicting these modes. Currently available analytical models were used to represent the liquid contributions, even though coupled longitudinal and lateral motions are present in such a complex structure. Agreement between the results was found in the lower few modes.

Kana, D. D.↗

An experimental study of axisymmetric modes in various propellant tanks containing liquid

An experimental study of several models used to analyze the longitudinal dynamics of oscillations in launch vehicle propellant tanks, is presented. Several vehicle structural configurations are considered: hemispherical and spherical, cylindrical and spherical, and semiellipsoidal and ellipsoidal. Various bulkheads and flanges are used with each configuration. The results are given in graphs.

Kana, D. D.↗