Computing the Effective Elasticity of Anisotropic Porous Media from X-Ray Computed Micro-Tomography Images
Explore the source record for details and available documents.
Federico Semeraro↗
Engineering topics
Nagi N. Mansour
Publications and source records attributed to Nagi N. Mansour.
Mechanical Erosion Modeling of TPS Materials
This work describes the development of a model that accounts for the additional surface recession in Thermal Protection Systems (TPS) materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics module was integrated within the Porous material Analysis Toolbox (PATO) based on OpenFOAM. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model capable to predict the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.
Stress Analysis↗
Analysis of PICA-NuSil at the Hypersonic Materials Environmental Test System (HyMETS)
Phenolic Impregnated Carbon Ablator (PICA) gained heritage during theStardust mission and is the baseline thermal protection system (TPS) material for missions to Mars. However, PICA is friable, so a thin layer of siloxane resin (NuSil) is applied to the surface of the heat shield to suppress the spread of particulate matter during cleanroom activities. Until recently, the thermochemical response of NuSil had not been accounted for in material response models. Therefore, a test campaign was executed at the Hypersonic Materials Environmental Test System (HyMETS) facility to investigate the material response of NuSil and provide crucial insight for model development. Finally, salient results from an experiment supported by the AsteroidThreat Assessment Project (ATAP) will be discussed, which probed the materialr esponse of the Tamdakht meteorite and notable analogs.
Brody K. Bessire↗
Computation of Effective Mechanical Properties and Mechanical Erosion Modeling of TPS Materials
The goal of this presentation is to provide a general overview of the multi-scale modeling formulation to determine if there is additional surface recession in Thermal Protection Systems (TPS) materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. This modeling process is performed at different scales by leveraging two computational frameworks developed at NASA: the Porous Microstructure Analysis (PuMA) software, and the Porous material Analysis Toolbox based on OpenFOAM (PATO). PuMA specializes in computing effective macro-scale material properties by performing material response simulations on 3D digital micro-scale representations of porous micro-structures. The modeling of TPS materials at the micro-scale is essential to understand how they behave as part of a heat shield assembly. The first part of the presentation will detail the implementation of PuMA’s cell-centered finite volume elasticity solver, which allows the computation of macro-scale effective mechanical properties of heterogeneous and anisotropic materials such as fibrous and woven TPS composites. These homogenized mechanical properties are used by PATO’s mechanical erosion model to predict the TPS material’s recession at a larger scale. This work will also provide some examples of multi-scale analysis from the fiber level up to the unit cell. The second part of the presentation will focus on the macro-scale approach to determine if erosion at the heat shield’s surface occurs due to mechanical and thermal loads experienced during atmospheric entry. To accomplish this, a solid mechanics module was integrated within PATO enabling it to model the potential mechanical erosion in three steps: first, after obtaining the effective mechanical properties with PuMA, the implemented stress analysis solver computes the stress and the displacement fields for the TPS material using the wall shear stress tensor, computed using a CFD solver, as boundary conditions; then, regions on the surface where the stress meets the failure criteria are identified; finally, the failed material is removed and the mesh is redistributed accordingly. The outcome is a model capable of predicting the total recession in the material due to surface chemistry and mechanical erosion.
Mechanical Properties↗
Recent Advancements in the PATO Material Response Code
Introduction: Predicting the complicated multiphysics phenomena during atmospheric entry requires high-fidelity modeling tools to refine estimates of mission risks during entry. To this end, new capabilities are being added to the Porous-material Analysis Toolbox based on OpenFOAM (PATO) [1,2,3]. PATO is an open-source software for Computational Material Response (CMR) of reactive porous materials submitted to high-temperature environments. The objective of this work is to highlight current efforts to add to and improve upon the modeling capabilities of PATO. These include efforts to loosely couple PATO with other discipline specialized codes including hypersonic Computational Fluid Dynamics (CFD), to assess the interaction effects between pyrolysis gas blowing and the boundary layer, and Computational Solid Mechanics (CSM), to address modeling of mechanical erosion. Other refinements include surface phenomena modeling capabilities to address the effects of silicone-based coatings applied to the TPS during flight preparation, and a unified multiphase solver for a mixed porous-material and plain-fluid domain. Coupling CMR with CFD (CMR/CFD): A loose coupling between PATO and the Data Parallel Line Relaxation (DPLR) [4] CFD code has been achieved by making use of a blowing boundary condition at the heatshield surface available in DPLR. Starting with heat flux estimates with no pyrolysis gas blowing at the surface, blowing gases are computed by the CMR and passed to the CFD such that aerothermal properties of the environment can be recomputed for a new CMR computation. This leads to an iterative process which is supplemented with an estimate of the radiative heat flux using the Nonequilibrium air radiation (NEQAIR) [5] program. The entire iterative process is illustrated in Figure 1. This coupling strategy has been utilized in computing the MSL material response. The goal is to compare the coupled CMR/CFD results with material response results obtained using traditional blowing corrections. Coupling CMS with CMR: A mechanical erosion model is currently being implemented in PATO to account for the additional mass removal induced by high shear conditions. The modeling process at each timestep consists of updating the mechanical properties as a function of temperature and computing the stress tensor and displacement fields of the material. Then, a failure criteria model determines the regions in which the stress exceeds the ultimate strength values resulting in mesh movement to account for mass removal. This model allows the material response simulation to compute the recession due to both oxidation and shear-induced erosion. The model is demonstrated by computing material response of sphere-cone arc jet samples. Surface Modeling Capabilities: NuSil, a silicone-based coating, was sprayed onto the MSL and Mars 2020 heatshields to mitigate shedding of phenolic dust. To better understand the effects of the NuSil coating on the material response, a novel model has been implemented in PATO. In this model, the equilibrium of the charred NuSil surface is modeled as pure silica, and a constant offset, inspired by the classical spallation model, is added to the the char blowing rate and wall enthalpy to reproduce HyMETS experimental results. The model has also been used to estimate the 3D material response of the MSL heatshield [6]. Unified Solver: In addition to the iterative loose coupling approach mentioned above, a multiphase unified solver is being developed to couple the environment (plain-fluid phase) and the porous-material phase. The solver is based on the volume averaged conservation of mass, momentum, and energy for the macroscale with closure models which include microscale effects through effective physicochemical properties. The unified solver has been used to compute flow through a porous plug and solve the Beavers and Joseph problem [7]. Since the strong coupling between phases is inherent to this solver, modeling assumptions present in other coupling methods of material response are mitigated. This strategy also makes it feasible to capture the competition between surface and volume ablation in the same computational domain, which is usually not possible with other coupling approaches.
Thermal Protection Systems↗
Computation of Effective Mechanical Properties and Mechanical Erosion Modeling of TPS Materials
Explore the source record for details and available documents.
Mechanical Properties↗
Mechanical Erosion Modeling of TPS Materials
The goal of this work is to predict the mechanical response of TPS materials, and specifically, to determine if there is additional surface recession in the heat shield’s surface as a result of mechanical erosion due to the mechanical and thermal loads experienced during atmospheric entry. To accomplish this, a solid mechanics module was integrated within the PATO material response code, enabling it to model the potential mechanical erosion in three steps: first, having the effective mechanical properties as function of temperature, the implemented stress analysis solver computes the stress and the displacement fields for the TPS material using the wall shear stress tensor, computed with the DPLR hypersonic CFD code, as boundary conditions; then, regions on the surface where the stress meets the failure criteria are identified; finally, the failed material is removed and the mesh is redistributed accordingly. The outcome is a model capable of predicting the total recession in the TPS material due to surface chemistry and mechanical erosion.
Stress Analysis↗
Mechanical Erosion Modeling of TPS Materials
This work describes the development of a model that accounts for the additional surface recession in Thermal Protection Systems (TPS) materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics module was integrated within the Porous material Analysis Toolbox (PATO) based on OpenFOAM. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model capable to predict the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.
Stress Analysis↗
Porous Microstructure Analysis (PuMA) software
- Motivation and objectives - Overview of PuMA - Open-source release - Material properties computation - Artificial geometry generation - Property homogenization for anisotropic media - Fiber orientation - Conductivity - Elasticity - Permeability
homogenization↗
The Material Response of PICA-NuSil to a Hypersonic Flow Environment
Phenolic Impregnated Carbon Ablator (PICA) is NASA’s baseline thermal protection system for missions to Mars. PICA is friable; therefore, NuSil ® CV-1144-0 is applied to the surface of flight hardware to mitigate the contamination of spacecraft sensors. NuSil is composed of a polysiloxane resin system that can transform into an oxidation-resistant coating upon heating. Therefore, a pathfinder campaign was conducted at the Hypersonic Materials Environmental Test System (HyMETS) at the NASA Langley Research Center to investigate the material response of instrumented sphere-cone models made from PICA coated with NuSil ® . Analysis of the post-test data is presented and suggests that NuSil ® impacts the material response of test articles subjected to oxidizing atmospheres, as evidenced by a reduction of the measured surface temperature and in-depth temperature response. Finally, a four-step ablation mechanism is proposed based on observations from high-speed video, optical emission spectroscopy, thermal analysis, and post-test surface characterization.
PICA PICA-NuSil Siloxane Silicone↗
Material Characterization and Modeling of Room Temperature Vulcanizing Silicone
Room Temperature Vulcanizing silicone (RTV) is a high-temperature adhesive that has successfully been used as a gap-filler between Thermal Protection System (TPS) tiles for heatshields on numerous missions. It is also used to bond instrumentation plugs such as temperature and pressure sensors into the heatshields. While RTV has been traditionally assumed to be a non-porous and non-ablating material, numerous experiments have shown that RTV pyrolyzes and becomes highly porous as it is heated. Heating RTV has also shown swelling, or intumescence, which can pose unique problems that lead to roughness induced boundary-layer transition, surface oxide formation and contamination of heat shield sensors. Therefore, it is crucial to understand and model the intumescence phenomenon of RTV. As data for RTV material properties is limited, the first step in modeling RTV is to collect material properties such as pyrolysis mass-loss, microstructure change, virgin and char porosity, etc. which was performed in our initial study. Additionally, thermomechanical properties such as Young’s modulus and Poisson ratio are required for modeling the intumescence of RTV, which were taken from literature and the coefficient of thermal expansion was collected using in-situ heating and Micro Computed Tomography (µ-CT) in previous studies. Finally, numerous other properties such as pyrolysis gas properties, virgin and char thermal conductivity and specific heat were compiled from previous experiments and literature into a material database that can be used for simulations. In Porous Material Analysis Toolbox based on OpenFOAM (PATO) [4], structural mechanics coupled with material response was used for simulating the intumescence of RTV as it is heated. However, since the permeability of the material is very low, the pyrolysis gas creates an internal pressure build-up as the material is being heated, significantly contributing to the deformation of the material. To correctly characterize this phenomenon, additional physics models were implemented into PATO's stress analysis solver, and results were compared with RTV dilatometry test data as a preliminary verification case. Future work will include experiments of RTV at the Plasmatron X facility and the in-situ heating cell with µ-CT, and improvement of simulation tools to more accurately model RTV intumescence.
TPS↗
Recent Developments to the Porous Microstructure Analysis (PuMA) Software
Introduction The Porous Microstructure Analysis (PuMA) software is an open source framework for image-based simulation, primarily used to determine effective properties based on material microstructure. PuMA was originally developed for the study of NASA thermal protection materials; however, many of the solvers in PuMA have applicability to a broad range of materials science applications. PuMA version 3.2 computes material surface area, pore diameters, effective thermal conductivity, continuum and rarefied tortuosity, and permeability. For anisotropic materials, PuMA can estimate material orientation and compute anisotropic thermal conductivity and elasticity. In this talk, a brief overview of the PuMA software and underlying methods will be presented, as well as some recent and ongoing developments, including the use of immersed boundary methods for image-based simulation and the development of a new weave segmentation tool, called TomoSAM. Cut-Cell method for heat and mass transfer For simulations on complex microstructures, traditional unstructured meshing techniques often prove to be difficult and time-intensive. Voxel-based solvers, which represent the surface as a staircase structure, are relatively simple to implement but can lose accuracy when feature resolution is poor. In this work, we present a novel 3D cut-cell method for solving the variable coefficient Poisson equation on complex microstructures, suitable for the determination of effective thermal conductivity or tortuosity of a material. The method uses a Marching Cubes/Marching Squares surface reconstruction to create cut-cells and determine geometric quantities. A flux-correction method is extended to 3D, with least squares gradient reconstruction, to solve for the boundary fluxes in the cut-cells. Verification cases show the solver achieves globally 2nd order accuracy on complex microstructures. TomoSAM TomoSAM, a module of the PuMA software, has been developed as a plugin for 3D Slicer, a software platform used for 3D image processing and visualization. It utilizes the Segment Anything Model (SAM), a deep learning model capable of identifying objects and generating image masks based on minimal user input. This feature enables efficient segmentation of complex 3D datasets, particularly of woven materials, from tomography or similar imaging methods, reducing the need for manual segmentation.
Tomography↗
Recent Developments to the Porous Microstructure Analysis (PuMA) Software
The Porous Microstructure Analysis (PuMA) software is an open source framework for image-based simulation, primarily used to determine effective properties based on material microstructure. PuMA was originally developed for the study of NASA thermal protection materials; however, many of the solvers in PuMA have applicability to a broad range of materials science applications. PuMA version 3.2 computes material surface area, pore diameters, effective thermal conductivity, continuum and rarefied tortuosity, and permeability. For anisotropic materials, PuMA can estimate material orientation and compute anisotropic thermal conductivity and elasticity. In this talk, a brief overview of the PuMA software and underlying methods will be presented, as well as some recent and ongoing developments, including the use of immersed boundary methods for image-based simulation and the development of a new weave segmentation tool, called TomoSAM. Cut-Cell method for heat and mass transfer For simulations on complex microstructures, traditional unstructured meshing techniques often prove to be difficult and time-intensive. Voxel-based solvers, which represent the surface as a staircase structure, are relatively simple to implement but can lose accuracy when feature resolution is poor. In this work, we present a novel 3D cut-cell method for solving the variable coefficient Poisson equation on complex microstructures, suitable for the determination of effective thermal conductivity or tortuosity of a material. The method uses a Marching Cubes/Marching Squares surface reconstruction to create cut-cells and determine geometric quantities. A flux-correction method is extended to 3D, with least squares gradient reconstruction, to solve for the boundary fluxes in the cut-cells. Verification cases show the solver achieves globally 2nd order accuracy on complex microstructures. TomoSAM TomoSAM, a module of the PuMA software, has been developed as a plugin for 3D Slicer, a software platform used for 3D image processing and visualization. It utilizes the Segment Anything Model (SAM), a deep learning model capable of identifying objects and generating image masks based on minimal user input. This feature enables efficient segmentation of complex 3D datasets, particularly of woven materials, from tomography or similar imaging methods, reducing the need for manual segmentation.
Tomography↗
In-situ Imaging of Pyrolyzing Aerospace Materials
Tracking morphological changes of materials during heating is crucial to understand its response in fire protection, biofuel production, thermal protection systems (TPS) for hypersonic flight. As materials are heated, they undergo physical and chemical changes due to water loss, stretching or shrinking, pyrolysis and chemical reactions in the ambient environment. The effects of these changes can have a profound impact on the material’s performance, indicated by changes in on the porosity and volume. While materials such as wood shrink as they pyrolyze and lose mass, others swell due to their inherent characteristics when exposed to heat [1]. This study focuses on experiments conducted at the Advanced Light Source (ALS) beamline 8.3.2, where in situ micro-computed tomography (µ-CT) is performed on materials as they are being pyrolyzed. Through in situ µ-CT, the change in total volume and porosity can be obtained in real-time, allowing for better understanding of the underlying thermophysical and chemical processes as a function of temperature. This study also focuses on the implementation of the Porous Microstructure Analysis software (PuMA) [2] to obtain thermal conductivity, permeability, and other properties of the material from the 3D tomographies. The information gained from these tomographies will supplement microscale model development of material morphological change and will aid macroscale modeling for high-temperature applications. For this study, Room Temperature Vulcanizing silicone (RTV) [3-5] is heated from room temperature to 1000°C using an infrared lamp heating system, and tomographies are continuously collected as the sample is heated. The tomographies are then segmented to obtain solid and void phases, from which estimates of pore size, porosity and total volume are extracted as a function of temperature. PuMA is deployed on the segmented tomographies to obtain thermal conductivity, permeability, and other properties as a function of temperature. Preliminary results show that RTV first intumesces (swells) as pyrolysis begins, due to build-up of pyrolysis gases in closed pores, and then shrinks significantly as more open pores are formed and the pyrolysis gases outgas. Pore network visualization of the tomographies using OpenPNM [6] showed the increase in pore connectivity with increase in temperature. Future work will focus on using PuMA to obtain macroscopic properties of RTV as a function of temperature.
Tomography↗
Helioseismic Modeling of Background Flows
Explore the source record for details and available documents.
Andrey M. Stejko↗