Engineering Papers⌕ Search

Engineering topics

Murthy, S. N. B.

Publications and source records attributed to Murthy, S. N. B..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Aerothermal modeling program, phase 2. Element B: Flow interaction experiment

The design process was improved and the efficiency, life, and maintenance costs of the turbine engine hot section was enhanced. Recently, there has been much emphasis on the need for improved numerical codes for the design of efficient combustors. For the development of improved computational codes, there is a need for an experimentally obtained data base to be used at test cases for the accuracy of the computations. The purpose of Element-B is to establish a benchmark quality velocity and scalar measurements of the flow interaction of circular jets with swirling flow typical of that in the dome region of annular combustor. In addition to the detailed experimental effort, extensive computations of the swirling flows are to be compared with the measurements for the purpose of assessing the accuracy of current and advanced turbulence and scalar transport models.

Nikjooy, M.↗
NASA NTRS1986

Transient engine performance with water ingestion

The immediate effects on the transient performance of a generic, high bypass ratio jet engine on account of water ingestion are discussed. The air compression subsystem has been analyzed with respect to four aerothermodynamic and mechanical processes associated with two-phase fluid flow and the engine simulation has been carried out under three limiting cases of interest in practice, one pertaining to draining of water at the end of compression and the other two, to partial evaporation at two different locations in the burner. General observations are made on engine operability as a function of engine and control design under various engine and (control input) sensor operating conditions, with various mass fractions of water in the air-water mixture entering the engine, during various pilot-initiated power demand changes.

Haykin, T.↗
NASA NTRS1986

Direct and system effects of water ingestion into jet engine compresors

Water ingestion into aircraft-installed jet engines can arise both during take-off and flight through rain storms, resulting in engine operation with nearly saturated air-water droplet mixture flow. Each of the components of the engine and the system as a whole are affected by water ingestion, aero-thermally and mechanically. The greatest effects arise probably in turbo-machinery. Experimental and model-based results (of relevance to 'immediate' aerothermal changes) in compressors have been obtained to show the effects of film formation on material surfaces, centrifugal redistribution of water droplets, and interphase heat and mass transfer. Changes in the compressor performance affect the operation of the other components including the control and hence the system. The effects on the engine as a whole are obtained through engine simulation with specified water ingestion. The interest is in thrust, specific fuel consumption, surge margin and rotational speeds. Finally two significant aspects of performance changes, scalability and controllability, are discussed in terms of characteristic scales and functional relations.

Murthy, S. N. B.↗
NASA NTRS1985

Aerothermal modeling program, phase 2

The main objectives of the Aerothermal Modeling Program, Phase 2 are: to develop an improved numerical scheme for incorporation in a 3-D combustor flow model; to conduct a benchmark quality experiment to study the interaction of a primary jet with a confined swirling crossflow and to assess current and advanced turbulence and scalar transport models; and to conduct experimental evaluation of the air swirler interaction with fuel injectors, assessments of current two-phase models, and verification the improved spray evaporation/dispersion models.

Mongia, H. C.↗
NASA NTRS1985

A stagnation pressure probe for droplet-laden air flow

It is often of interest in a droplet-laden gas flow to obtain the stagnation pressure of both the gas phase and the mixture. A flow-decelerating probe (TPF), with separate, purged ports for the gas phase and the mixture and with a bleed for accumulating liquid at the closed end, has been developed. Measurements obtained utilizing the TPF in a nearly isothermal air-water droplet mixture flow in a smooth circular pipe under various conditions of flow velocity, pressure, liquid concentration and droplet size are presented and compared with data obtained under identical conditions with a conventional, gas phase stagnation pressure probe (CSP). The data obtained with the CSP and TPF probes are analyzed to determine the applicability of the two probes in relation to the multi-phase characteristics of the flow and the geometry of the probe.

Murthy, S. N. B.↗
NASA NTRS1984

Jet through a wall protrusion in a cross-flow

The flow interactions between a jet issuing out of a protrusion in a wall and a crosswise flow are of interest because of the manner in which the spreading and mixing of the jet are affected by the flow separation, formation of vortices and recirculation zones and the associated flow instabilities. In combustors and in aircraft void spaces adjoining fuel tanks such interactions determine flame stability and propagation characteristics. Results from flow visualization and from predictions based on a three-dimensional viscous flow code are utilized to show the effects of several flow and geometrical parameters on the processes occuring in the vicinity of the protrusion and the jet.

Hong, S. K.↗
NASA NTRS1984

Pressure-strain correlations in curved wall boundary layers

Pressure-strain correlations, which represent some part of production and dissipation of Reynolds stress in turbulent wall-bounded shear layers, have been determined for the cases of boundary layer flow past a convex, a concave and a flat wall, the latter also in the case when it follows a convex wall (relaxing flow). The Large Eddy Interaction Model utilized for prediction also permits determination of the contribution from different parts of the turbulence spectra to the correlations in different parts across the boundary layer. The relation between the anisotropic nature of the correlations and the spectra in the different flow cases provides a means of testing models for the correlations.

Hong, S. K.↗
NASA NTRS1983

Axial-compressor flow distortion with water ingestion

The objective of the investigation is as follows: to establish relations between the steady state mean flow distortion generated during water ingestion into an axial-flow compressor and (a) characteristic length and time scales pertaining to (1) the centrifugal action and (2) the heat and mass transfer processes and (b) aerodynamic parameters based on blade geometry, aspect ratio and blade loading. Analytical and experimental results are presented for a small compressor to illustrate the extent of the distortion introduced as a function of (1) the operating speed and (2) the mass-based water content in the ingested mixture. Methods of scaling the effects in compressors of different sizes are discussed.

Tsuchiya, T.↗
NASA NTRS1983

Effect of humidity on jet engine axial-flow compressor performance

Two problems related to the ingestion of humid air into jet engine axial compressors have been studied: (1) the changes in the performance of the compressor in the absence of condensation and (2) the changes in the entry conditions to the compressor when condensation occurs. Regarding the first, the extent of changes are predicted and also measured in the case of a six-stage compressor operated with air-methane gas mixture utilizing the similarities in the thermodynamic properties between water vapor and methane. For the condensation process in an inlet, a model is described that takes into account the presence of micro particulates and the flow field changes in the vicinity of the inlet wall. Finally, the effects of humidity on engine performance are discussed in relation to engine trim and control schemes.

Ehresman, C. M.↗
NASA NTRS1982

The WISGSK: A computer code for the prediction of a multistage axial compressor performance with water ingestion

A computer code is presented for the prediction of off-design axial flow compressor performance with water ingestion. Four processes were considered to account for the aero-thermo-mechanical interactions during operation with air-water droplet mixture flow: (1) blade performance change, (2) centrifuging of water droplets, (3) heat and mass transfer process between the gaseous and the liquid phases and (4) droplet size redistribution due to break-up. Stage and compressor performance are obtained by a stage stacking procedure using representative veocity diagrams at a rotor inlet and outlet mean radii. The Code has options for performance estimation with (1) mixtures of gas and (2) gas-water droplet mixtures, and therefore can take into account the humidity present in ambient conditions. A test case illustrates the method of using the Code. The Code follows closely the methodology and architecture of the NASA-STGSTK Code for the estimation of axial-flow compressor performance with air flow.

Tsuchiya, T.↗
NASA NTRS1982

Water ingestion into jet engine axial compressors

An axial flow compressor has been tested with water droplet ingestion under a variety of conditions. The results illustrate the manner in which the compressor pressure ratio, efficiency and surging characteristics are affected. A model for estimating the performance of a compressor during water ingestion has been developed and the predictions obtained compare favorably with the test results. It is then shown that with respect to five droplet-associated nonlinearly-interacting processes (namely, droplet-blade interactions, blade performance changes, centrifugal action, heat and mass transfer processes and droplet break-up), the initial water content and centrifugal action play the most dominant roles.

Tsuchiya, T.↗
NASA NTRS1982

PURDU-WINCOF: A computer code for establishing the performance of a fan-compressor unit with water ingestion

A model for predicting the performance of a multi-spool axial-flow compressor with a fan during operation with water ingestion was developed incorporating several two-phase fluid flow effects as follows: (1) ingestion of water, (2) droplet interaction with blades and resulting changes in blade characteristics, (3) redistribution of water and water vapor due to centrifugal action, (4) heat and mass transfer processes, and (5) droplet size adjustment due to mass transfer and mechanical stability considerations. A computer program, called the PURDU-WINCOF code, was generated based on the model utilizing a one-dimensional formulation. An illustrative case serves to show the manner in which the code can be utilized and the nature of the results obtained.

Leonardo, M.↗