Engineering topics

Munroe, Paul

Publications and source records attributed to Munroe, Paul.

3 records

DOE OSTI2019

Deterministic Ferroelastic Domain Switching Using Ferroelectric Bilayers

Composition gradients, or dissimilar ferroelectric bilayers, demonstrate colossal electromechanical figures of merit attributed to the motion of ferroelastic domain walls. Yet, mechanistic understanding of polarization switching pathways that drive ferroelastic switching in these systems remains elusive. Here, the crucial roles of strain and electrostatic boundary conditions in ferroelectric bilayer systems are revealed, which underpin their ferroelastic switching dynamics. Using in situ electrical biasing in the transmission electron microscope (TEM), the motion of ferroelastic domain walls is investigated in a tetragonal (T) Pb(Zr,Ti)O 3 (PZT)/rhombohedral (R) PZT epitaxial bilayer system. Atomic resolution electron microscopy, in tandem with phase field simulations, indicates that ferroelastic switching is triggered by predominant nucleation at the triple domain junctions located at the interface between the T/R layers. Furthermore, this interfacial nucleation leads to systematic reversable reorientation of ferroelastic domain walls. Finally, deterministic ferroelastic domain switching, driven by the interfacial strain and electrostatic boundary conditions in the ferroelectric bilayer, provides a viable pathway toward novel design of miniaturized energy-efficient electromechanical devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2019

The effects of carbon on the phase stability and mechanical properties of heat-treated FeNiMnCrAl high entropy alloys

This work systematically investigates the effect of carbon on the phase stability and room- temperature tensile performance of an annealed Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 (at%) high entropy alloy without (HEA) and with 1.1% carbon (CHEA). Four annealing conditions were investigated: 773 K for 13 d and 42 d, 973 K for 20 d, and 1073 K and 1423 K for 24 h. The resulting microstructures were analyzed using a combination of scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and atom probe tomography (APT). Vickers hardness testing and room- temperature tensile testing were used to determine the mechanical properties of the annealed HEA and the CHEA. APT composition profiles revealed fine Ni,Mn,Al-enriched matrix precipitates in the CHEA annealed at 773 K for 13 d. After ageing at 773 K for 42 d, colonies of (Ni,Fe) 2 MnAl- enriched Heusler phase lamellae were observed at the grain boundaries (GBs) and in the matrix for the HEA, while GB lamellar colonies of Mn,Cr-enriched M 23 C 6 carbides were observed for the CHEA. Due to the presence of the GB carbides, the resulting room-temperature elongation to fracture for the CHEA annealed at 773 K for 42 d was ~1% compared to ~11% for the HEA given the same anneal. At higher annealing temperatures, the microstructure contains Ni,Al-rich and Mn,Cr,C-rich precipitates that alternate along the GBs and appear to be associated with each other in the matrix. Electron diffraction analysis indicates the aforementioned Ni,Al-precipitates and Mn,Cr-carbides have b.c.c. and f.c.c. crystal structures, respectively. Once again, a low elongation to fracture (2%) was seen for the carbon-containing material compared to its un-doped counterpart (23%) which solely contained Ni,Al-rich b.c.c. precipitates.

36 MATERIALS SCIENCE↗

NASA NTRS1989

Room temperature tensile ductility in polycrystalline B2 Ni-30Al-20Fe

A room-temperature tensile elongation of about 2.5 percent, where the only slip vector observed was the 100, has been determined for a double-extruded B2 Ni-30Al-20Fe alloy consisting of recrystallized equiaxed grains about 25 microns in diameter; these results suggest that 100-slip does not preclude limited ductility in polycrystalline B2 alloys in tension at low temperatures. A suppression of ordering through resort to rapid solidification, in other words, is not necessary for ductility, since the cast and as-extruded alloy presently examined is ordered.

Guha, Sumit↗