Engineering topics

Mularz, E. J.

Publications and source records attributed to Mularz, E. J..

26 records · Page 2

NASA NTRS1976

Results of the pollution reduction technology program for turboprop engines

A program was performed to evolve and demonstrate advanced combustor technology aimed at achieving the 1979 EPA standards for turboprop engines (Class P2). The engine selected for this program was the 501-D22A turboprop manufactured by Detroit Diesel Allison Division of General Motors Corporation. Three combustor concepts were designed and tested in a combustor rig at the exact combustor operating conditions of the 501-D22A engine over the EPA landing-takeoff cycle. Each combustor concept exhibited pollutant emissions well below the EPA standards, achieving substantial reductions in unburned hydrocarbons, carbon monoxide, and smoke emissions compared with emissions from the production combustor of this engine. Oxides of nitrogen emissions remained well below the EPA standards, also.

Mularz, E. J.↗

NASA NTRS1976

Results of the pollution reduction technology program for turboprop engines

A program was performed to evolve and demonstrate advanced combustor technology aimed at achieving the 1979 EPA standards for turboprop engines (Class P2). The engine selected for this program was the 501-D22A turboprop. Three combustor concepts were designed and tested in a combustor rig at the exact combustor operating conditions of the 50-D22A engine over the EPA landing-takeoff cycle. Each combustor concept exhibited pollutant emissions well below the EPA standards, achieving substantial reductions in unburned hydrocarbons, carbon monoxide, and smoke emissions compared with emissions from the production combustor of this engine. Oxides of nitrogen emissions remained well below the EPA standards, also.

Mularz, E. J.↗

NASA NTRS1975

Flow characteristics of various swirl-can module designs

Flow measurements were performed on each of six swirl-can combustor module designs under simulated combustor operating conditions to find the design which exhibited a small recirculation zone, intense air mixing, and good fuel distribution in its wake. Conditions that are favorable for producing low oxides of nitrogen emissions and high combustion efficiency were investigated. The recirculation zone, the turbulence intensity and the fuel distribution pattern are obtained in the wake region of the center module of a three module array. The most promising swirl-can module design incorporates two air swirlers which discharge air in opposite directions (contraswirl), mixes the fuel and air upstream of the inner swirler, and has a flow area blockage of 64.3% for the three module array.

Mularz, E. J.↗

NASA NTRS1975

Exhaust pollutant emissions from swirl-can combustor module arrays at parametric test conditions

Improved designs of swirl-can combustor modules were tested using seven-module arrays in a combustor. The combustor was operated over a pressure range of 69 to 207 N/sq cm, a fuel-air ratio range of 0.015 to 0.046, at a constant inlet air temperature of 733 K, and at reference velocities of 23.9 and 30.6 m/sec. The three designs tested performed with high combustion efficiency at all conditions tested and exhibited oxides of nitrogen emissions substantially lower than that of conventional gas turbine combustors. A correlating parameter used to extrapolate oxides of nitrogen emissions to full power or takeoff conditions for large commercial turbofan engines predicts oxides of nitrogen emissions somewhat higher than those specified in the 1979 government emissions standards.

Mularz, E. J.↗

NASA NTRS1975

Pollution emissions from single swirl-can combustor modules at parametric test conditions

Exhaust pollutant emissions were measured from single swirl-can combustor modules operating over a pressure range of 69 to 276 N/sq cm (100 to 400 psia), over a fuel-air ratio range of 0.01 to 0.04, at an inlet air temperature of 733 K (860 F), and at a constant reference velocity of 23.2 m/sec). Many swirl-can module designs were evaluated; the 11 most promising designs exhibited oxides of nitrogen emission levels lower than that from conventional gas-turbine combustors. Although these single module test results are not necessarily indicative of the performance characteristics of a large array of modules, the results are very promixing and offer a number of module designs that should be tested in a full combustor.

Mularz, E. J.↗

NASA NTRS1972

An experimental investigation of radiative properties of aluminum oxide particles.

The radiative properties of aluminum oxide at high temperatures were determined at various wavelengths. Absorption cross-sections of aluminum oxide particles averaged over a particle size distribution were determined by measuring the radiative emission from the particles in a flame and by determining the particle number density and size distribution from measurements of the scattering of laser light incident on the particles in this flame. From these values of average absorption cross-section, the imaginary part of the refractive index was deduced. Results indicate that the absorption cross-section and the imaginary part of the refractive index increase as the temperature increases in the range from 1920 to 2610 K, and that these properties decrease with increasing wavelength in the interval from 0.35 to 1.2 micron, indicating a nongray-body behavior.

Mularz, E. J.↗

NASA NTRS1972

Factors affecting altitude relight performance of a double-annular ram-induction combustor

A test program was conducted to evaluate the altitude relight capabilities of a short-length, double-annular, ram-induction combustor which was designed for Mach 3 cruise operation. The use of distorted inlet-air flow profiles was tried to evaluate their effect on the relight performance. No significant improvement in altitude relight performance was obtained with this approach. A study was also made to determine the effects of the reference Mach number, the fuel temperature, and the fuel volatility (ASTM-A1 against JP-4) on the altitude relight performance. Decreasing the reference Mach number, increasing the fuel temperature, and using more volatile fuel all decrease the combustor pressure necessary for relight.

Schultz, D. F.↗

NASA NTRS1972

Performance of a swirl-can combustor at idle conditions

Test results of a full annulus swirl-can combustor operated at simulated engine idle conditions indicated that significant improvements in combustion efficiency and accompanying reductions in pollutants could be realized with radial scheduling of fuel. Test conditions were an inlet air temperature of 478 K, a pressure of 4 atmospheres, and a reference velocity of 26 meters per second. At a fuel-air ratio of 0.008, radial scheduling of fuel increased combustion efficiency from less than 50 percent with no scheduling to nearly 100 percent and produced emission index values of unburned hydrocarbons and carbon monoxide of 10 and 40, respectively.

Niedzwiecki, R. W.↗