Engineering topics
Morrison, A.
Publications and source records attributed to Morrison, A..
Flat-plate solar array project. Volume 3: Silicon sheet: Wafers and ribbons
The primary objective of the Silicon Sheet Task of the Flat-Plate Solar Array (FSA) Project was the development of one or more low cost technologies for producing silicon sheet suitable for processing into cost-competitive solar cells. Silicon sheet refers to high purity crystalline silicon of size and thickness for fabrication into solar cells. Areas covered in the project were ingot growth and casting, wafering, ribbon growth, and other sheet technologies. The task made and fostered significant improvements in silicon sheet including processing of both ingot and ribbon technologies. An additional important outcome was the vastly improved understanding of the characteristics associated with high quality sheet, and the control of the parameters required for higher efficiency solar cells. Although significant sheet cost reductions were made, the technology advancements required to meet the task cost goals were not achieved.
High-Purity Silicon Seeds for Silane Pyrolysis
Seed particles for fluidized-bed production of silicon made by new contamination-free, economical method. In new method, large particles of semiconductor-grade silicon fired at each other by high-speed streams of gas and thereby break up into particles of suitable size for fluidized bed. No foreign materials introduced, and leaching unnecessary. Method used to feed fluidized-bed reactor for continuous production of high-purity silicon.
Fines in fluidized bed silane pyrolysis
Silicon deposition on silicon seed particles by silane pyrolysis in a fluidized-bed reactor is investigated as a low-cost, high-throughput method to produce high-purity polysilicon for solar-cell applications. Studies of fines, particles 0.1-10 microns diam, initiated from homogeneous decomposition in the reactor were conducted using 2 and 6-in-diam fluidized beds. The studies show functional dependences of fines elutriation on silane feed concentration, temperature, gas velocity, and bubble size. The observation that the fines elutriation is generally below 10 percent of the silicon-in-silane feed is attributed to scavenging by large particles in an environment of less free space for homogeneous nucleation. Preliminary results suggest that, with proper conditions and distributor design, high-silane-concentration (over 50 percent SiH4 in H2) feed may be used.
Fluidized bed silicon deposition
The growth of silicon on seed particles from the pyrolysis of silane in a fluidized bed reactor (FBR) was studied. The grown particles were shown to be crystalline and to have a structure which has been interpreted to indicate growth by chemical vapor deposition as well as by the collection (scavenging) of silicon clusters on seed particle surfaces. Scanning electron microscopy was used to study the product morphology.
Correlation of solar cell electrical properties with material characteristics of silicon cast by the ubiquitous crystallization process
Solar cells were fabricated using a conservative 'baseline' process on 1-3 Omega-cm p-type silicon from ingots cast by the ubiquitous crystallization process. Conversion efficiencies of the cells were measured, as well as spectral response and minority carrier diffusion length. Adjacent slices from the same ingot were studied for their grain size, dislocation distribution, and impurity distribution. Cell performance was related to the observed structural features, as well as to the chemical structure of the ingot.
Energy requirement for the production of silicon solar arrays
The results of a study to investigate the feasibility of manufacturing photovoltaic solar array modules by the use of energy obtained from similar or identical photovoltaic sources are presented. The primary objective of this investigation was the characterization of the energy requirements of current and developing technologies which comprise the photovoltaic field. For cross-checking the energies of prevailing technologies data were also used and the wide-range assessment of alternative technologies included different refinement methods, various ways of producing light sheets, semicrystalline cells, etc. Energy data are utilized to model the behavior of a future solar breeder plant under various operational conditions.
Energy requirement for the production of silicon solar arrays
An assessment of potential changes and alternative technologies which could impact the photovoltaic manufacturing process is presented. Topics discussed include: a multiple wire saw, ribbon growth techniques, silicon casting, and a computer model for a large-scale solar power plant. Emphasis is placed on reducing the energy demands of the manufacturing process.
Single Crystal Membranes
Single crystal a- and c-axis tubes and ribbons of sodium beta-alumina and sodium magnesium beta-alumina were grown from sodium oxide rich melts. Additional experiments grew ribbon crystals containing sodium magnesium beta, beta double prime, beta triple prime, and beta quadruple prime. A high pressure crystal growth chamber, sodium oxide rich melts, and iridium for all surfaces in contact with the melt were combined with the edge-defined, film-fed growth technique to grow the single crystal beta-alumina tubes and ribbons. The crystals were characterized using metallographic and X-ray diffraction techniques, and wet chemical analysis was used to determine the sodium, magnesium, and aluminum content of the grown crystals.
Atlas of interpreted photography of southern Africa from TIROS satellites I to VIII
Surface features of southern Africa based on interpreted photographs taken by TIROS SATELLITES
Photography of the western sahara desert from the mercury ma-4 spacecraft
Photography of western Sahara Desert from Mercury MA-4 spacecraft
Photography of the earth from space and its non-meteorological applications
Photography of earth surface from rockets and artificial satellites