Engineering topics

Morris, R. V.

Publications and source records attributed to Morris, R. V..

At least 253 records · Page 14

NASA NTRS1995

Reflectivity and other physicochemical properties of Mn-substituted goethites and hematites

Goethite-bearing samples with values of Mn(s) (Mn/(Mn+Fe) mole fraction) up to 0.206 were synthesized by precipitation from alkaline solution. Samples with Mn(s) less than or equal 0.061 were single-phase Mn-goethites: samples with higher Mn(s) values contained another Mn-bearing phase (probably jacobsite). Mn-hematites were prepared by dehydroxylation of corresponding Mn-goethites at 500 C. Orthorhombic a and b unit cell dimensions of Mn-goethites changed in a linear manner with Mn(s), but not at rates predicted by the Vegrad law. Hexagonal unit cell dimensions of Mn-hematites did not vary with Mn(s). Moessbauer parameters isomer shift (IS), quadrupole splitting (QS), and hyperfine field (B(sub hf)) were measured at 293 and 15 K. For all single-phase Mn-goethites and Mn-hematites (Mn(s) less than or equal 0.061), magnetic splitting was observed at both temperatures. At 293 K, small but systematic decreases in B(sub hf) were observed with increasing Mn substitution; IS and QS were not dependent on Mn(s). Mn substitution strongly lowered the Morin transition temperature of hematite. At 15 K, the Morin transition was not present for Mn(s) greater than 0.020(4). The saturation magnetization of Mn-goethites and Mn-hematites (Mn(s) less than or equal 0.061) was the expected zero (within error) for antiferromagnetic goethite and for hematites obtained from dehydroxylation of goethites. Mn-geothites with Mn(s) greater than 0.061 were magnetic because of the presence of strongly magnetic jacobsite. For reflectivity spectra, bands resulting from MN(3+) were centered near 454 and 596 nm for Mn-goethites and near 545 and 700 nm for Mn-hematites. There is evidence for a approximately 700 nm band in spectral data for Martian bright regions, but association of it with Mn(3+) is not a unique interpretation. Comparison of laboratory and Martian spectral data implies that Mn(s) less than 0.032 for the Mn(3+) content of Martian hematites.

Vempati, R. K.↗

NASA NTRS1994

Reduction of lunar mare soil and pyroclastic glass

Mare soil and orange and black pyroclastic glass were reduced in hydrogen gas at temperatures of 900 to 1100 C. The experiments support studies of regolith maturation, lunar volcanism, and the production of oxygen on the moon. The most reactive component in the high-Ti soil was FeO in ilmenite, which was completely reduced to iron metal at all temperatures. Vitreous orange glass crystallized and was partially reduced to iron metal, pyroxene, and minor olivine. Initially devitrified black glass was similarly reduced and converted to iron metal, pyroxene, and minor olivine. The degree of reaction in both glasses increased with temperature.

Allen, C. C.↗

NASA NTRS1994

Single agglutinates: A comparative study of compositions of agglutinitic glass, whole-grain, bulk soil, and FMR

Previous workers on single agglutinates have variously interpreted the composition of agglutinitic glass to represent impact melts of (1) bulk soil, (2) mixed components in finer sizes, and (3) microtargets. Separately, Papike has argued in favor of fusion of the finest fraction of bulk soils. Thirty-four single agglutinates were hand-picked from the mature Apollo 16 soil 61181 (I(sub s)/FeO = 82) and the FMR and chemical composition (INAA for Fe, Sc, Sm, Co, Ni, and Cr) of each agglutinate particle were measured. Thirteen of these single agglutinates were selected for electron beam microanalysis and imaging. Less than 1 micron spots were analyzed (for Na, Mg, Al, Si, P, S, K, Ca, Ti, Cr, Mn, Fe, Ni, and Ba) on pure glassy areas (approximately ten in each particle) selected on the basis of optical and BSE images (avoiding all clasts and inclusions) with an electron microprobe to obtain average glass compositions of each single agglutinate.

Basu, A.↗

NASA NTRS1994

High Resolution Transmission Electron Microscopy (HRTEM) of nanophase ferric oxides

Iron oxide minerals are the prime candidates for Fe(III) signatures in remotely sensed Martian surface spectra. Magnetic, Mossbauer, and reflectance spectroscopy have been carried out in the laboratory in order to understand the mineralogical nature of Martian analog ferric oxide minerals of submicron or nanometer size range. Out of the iron oxide minerals studied, nanometer sized ferric oxides are promising candidates for possible Martian spectral analogs. 'Nanophase ferric oxide (np-Ox)' is a generic term for ferric oxide/oxihydroxide particles having nanoscale (less than 10 nm) particle dimensions. Ferrihydrite, superparamagnetic particles of hematite, maghemite and goethite, and nanometer sized particles of inherently paramagnetic lepidocrocite are all examples of nanophase ferric oxides. np-Ox particles in general do not give X-ray diffraction (XRD) patterns with well defined peaks and would often be classified as X-ray amorphous. Therefore, different np-Oxs preparations should be characterized using a more sensitive technique e.g., high resolution transmission electron microscopy (HRTEM). The purpose of this study is to report the particle size, morphology and crystalline order, of five np-Ox samples by HRTEM imaging and electron diffraction (ED).

Golden, D. C.↗

NASA NTRS1994

Mossbauer and spectral (visible and near-IR) data for Fe(3+)-substituted rutile

Titanohematite and rutile containing some Fe(3+) are possible highly oxidized weathering products of ilmenite and titanomagnetities. We report here Moessbauer and reflectivity data (visible and near-IR) for Fe(3+)-substituted rutile as a part of our continuing studies of ferric-substituted minerals that might have bearing on the interpretation of Martian spectral data.

Lauer, H. V., Jr.↗

NASA NTRS1993

Pigmenting agents in Martian soils: inferences from spectral, Mossbauer, and magnetic properties of nanophase and other iron oxides in Hawaiian palagonitic soil PN-9

We have examined a Hawaiian palagonitic tephra sample (PN-9) that has spectroscopic similarities to Martian bright regions using a number of analytical techniques, including Mossbauer and reflectance spectroscopy, X-ray diffraction, instrumental neutron activation analysis, electron probe microanalysis, transmission electron microscopy, and dithionite-citrate-bicarbonate extraction. Chemically, PN-9 has a Hawaiitic composition with alkali (and presumably silica) loss resulting from leaching by meteoric water during palagonitization; no Ce anomaly is present in the REE pattern. Mineralogically, our results show that nanophase ferric oxide (np-Ox) particles (either nanophase hematite (np-Hm) or a mixture of ferrihydrite and np-Hm) are responsible for the distinctive ferric doublet and visible-wavelength ferric absorption edge observed in Mossbauer and reflectivity spectra, respectively, for this and other spectrally similar palagonitic samples. The np-Ox particles appear to be imbedded in a hydrated aluminosilicate matrix material; no evidence was found for phyllosilicates. Other iron-bearing phases observed are titanomagnetite, which accounts for the magnetic nature of the sample; olivine; pyroxene; and glass. By analogy, np-Ox is likely the primary pigmenting agent of the bright soils and dust of Mars.

Minerals/analysis↗

NASA NTRS1993

Microscopic iron metal on glass and minerals - A tool for studying regolith maturity

A novel method of producing mixtures of glass or minerals with iron metal is presented. A portion of the Fe(2+) in basaltic glass and minerals can be reduced to metal in a few hours at 1100 C and an oxygen fugacity well below the iron-wustite buffer. Part of the iron metals forms rounded submicrometer blebs on the surfaces and in some cases within the grains. A concentration of such blebs equivalent to 20-30 percent of a grain's surface area can totally dominate the reflectance spectra of basaltic glass, pyroxene, and olivine. The production of optically opaque iron metal blebs, combined with the decline in Fe(2+), affects the glass and mineral reflectance spectra in three ways: by lowering the overall reflectivity, reducing the spectral contrast of absorption features, and producing a continuum with a general rise in reflectivity toward longer wavelengths.

Allen, C. C.↗

NASA NTRS1993

Backscatter Mossbauer Spectrometer (BaMS) for extraterrestrial applications

Mossbauer spectroscopy is a nuclear gamma resonance technique particularly well suited to the study of materials that contain iron (Fe-57). It can provide information on the oxidation state of iron as well as the type and proportion of iron-containing mineral species in a sample of interest. Iron Mossbauer spectroscopy (FeMS) has been applied to samples believed to have come from Mars (SNC meteorites) and has been helpful in refining the choice among putative Martian surface materials by suggesting a likely nanophase component of the Martian regolity. FeMS spectrum of a Martial analogue material (Hawaiian palagonite) is shown; it is dominated by ferric-bearing phases and shows evidence of a nanophase component. FeMS has also been applied to lunar materials. It can be used to measure the maturity of lunar surface material and has been proposed as a prospector for lunar ilmenite, an oxygen resource mineral. Several years ago we suggested a backscatter Mossbauer spectrometer (BaMS) for a Mars rover mission. Backscatter design was selected as most appropriate for in-situ application because no sample preparation is required. Since that time, we have continued to develop the BaMS instrument in anticipation that it would eventually find a home on a NASA planetary mission. Gooding proposed BaMS as a geochemistry instrument on MESUR. More recently, an LPI workshop has recommended that BaMS be included in a three-instrument payload on the next (1996?) lunar lander.

Agresti, D. G.↗

NASA NTRS1993

Mineralogy of three slightly palagonitized basaltic tephra samples from the summit of Mauna Kea, Hawaii

The paper characterizes the mineralogy and spectral properties of three slightly palagonitized basaltic tephra samples collected near the summit of Mauna Kea in order to contribute to the basis for inferring mineralogy and processes for Martian surface materials. The mineralogy of size fractions of these samples is examined by diffuse reflectance and FIR spectroscopy, optical microscopy, X-ray diffraction, Moessbauer spectroscopy, magnetic analysis, EMPA, TEM, and SEM. For the 20-1000 micron size fraction, sample HWMK11 (red) is essentially completely oxidized and has a hematite (Ti-hematite) pigment dispersed throughout the silicate matrix. Sample HWMK12 (black) has the lowest proportion of ferric-bearing phases and is thus least weathered. For HWMK11, the amount of hematite is essentially constant, and mica is present only in the coarse clay-sized fraction; smectites are low in structural Fe.

Golden, D. C.↗

NASA NTRS1993

Prototype Backscatter Moessbauer Spectrometer for Measurement of Martian Surface Mineralogy

We have designed and successfully tested a prototype of a backscatter Moessbauer spectrometer (BaMS) targeted for use on the Martian surface to (1) determine oxidation states of iron, and (2) identify and determine relative abundances of iron-bearing mineralogies. No sample preparation is required to perform measurements; it is only necessary to bring sample and instrument into physical contact. The prototype meets our projected specification for a flight instrument in terms of mass, power, and volume. A Moessbauer spectrometer on the Martian surface would provide wide variety of information about the current state of the Martian surface, and this information is described.

Shelfer, T. D.↗

NASA NTRS1993

Effects of microscopic iron metal on the reflectance spectra of glass and minerals

Maturity, which is a measure of the time lunar soils have been in the upper approximately 1 mm of the surface, is correlated with changes in the soils' optical properties. Mature soil is darker and somewhat redder than immature soil of the same composition, and features in the reflectance spectrum become more subdued with increasing maturity. The maturation process also involves accumulation of agglutinitic glass and submicroscopic metallic iron particles. We have produced submicrometer iron metal blebs on the surface and within glass and mineral grains by the method of high-temperature reduction. This technique has permitted the determination of optical changes in samples much simpler than lunar soil, and offers a useful tool with which to investigate the maturation process.

Allen, C. C.↗

NASA NTRS1993

First oxygen from lunar basalt

The Carbotek/Shimizu process to produce oxygen from lunar soils has been successfully demonstrated on actual lunar samples in laboratory facilities at Carbotek with Shimizu funding and support. Apollo sample 70035 containing approximately 25 percent ilmenite (FeTiO3) was used in seven separate reactions with hydrogen varying temperature and pressure: FeTiO3 + H2 yields Fe + TiO2 + H2O. The experiments gave extremely encouraging results as all ilmenite was reduced in every experiment. The lunar ilmenite was found to be about twice as reactive as terrestrial ilmenite samples. Analytical techniques of the lunar and terrestrial ilmenite experiments performed by NASA Johnson Space Center include iron Mossbauer spectroscopy (FeMS), optical microscopy, SEM, TEM, and XRD. The Energy and Environmental Research Center at the University of North Dakota performed three SEM techniques (point count method, morphology determination, elemental mapping), XRD, and optical microscopy.

Gibson, M. A.↗

NASA NTRS1993

Terrestrial impact melts as analogues for the hematization of Martian surface materials

Visible and near-IR reflectivity and Mossbauer data were obtained on powders of hydrothermally-altered impact melt sheets from West Clearwater Lake, Manicouagan, and Ries (Polsingen) impact structures. The data support previous interpretations that Martian bright regions spectra can be interpreted by a ferric-bearing phase that has a relatively featureless absorption edge together with some well-crystalline (bulk) hematite to account for the 860 nm hematite band. The data also show that bands at wavelengths longer than 900 nm, which are characteristic of Martian dark regions, occur when both hematite and pyroxene are present. It thus follows that hematization of Mars can be attributed, at least in part, to hydrothermal alterations of impact melt sheets. Impact heating could also form bulk-Hm from nanophase ferric oxides.

Morris, R. V.↗

NASA NTRS1993

Combined backscatter Moessbauer spectrometer/x ray fluorescence analyzer (BaMS/XRF) for extraterrestrial surfaces

We have designed and tested a prototype combined backscatter Moessbauer spectrometer and x-ray fluorescence analyzer (BaMS/XRF). A space qualified instrument based on this design would be suitable for in-situ use on planetary missions to the surfaces of the Moon (Artemis and lunar outpost), Mars (MESUR), asteroids, or other solid solar system objects. The BaMS/XRF instrument is designed to be capable of concurrent sample analyses for the mineralogy of iron-bearing phases and elemental composition without the need for sample preparation.

Shelfer, T. D.↗

NASA NTRS1993

An attempt to comprehend Martian weathering conditions through the analysis of terrestrial palagonite samples

Spectroscopic observations of the Martian surface in the invisible to near infrared (0.4-1.0 micron), coupled with measurements made by Viking, have shown that the surface is composed of a mixture of fine-grained weathered and nonweathered minerals. The majority of the weathered components are thought to be materials like smectite clays, scapolite, or palagonite. Until materials are returned for analysis there are two possible ways of proceeding with an investigation of Martian surface processes: (1) the study of weathering products in meteorites that have a Martian origin (SNC's), and (2) the analysis of certain terrestrial weathering products as analogs to the material found in SNC's, or predicted to be present on the Martian surface. We describe some preliminary measurements of the carbon chemistry of terrestrial palagonite samples that exhibit spectroscopic similarities with the Martian surface. The data should aid the understanding of weathering in SNC's and comparisons between terrestrial palagonites and the Martian surface.

Douglas, C.↗

NASA NTRS1993

Mineralogical diversity (spectral reflectance and Moessbauer data) in compositionally similar impact melt rocks from Manicouagan Crater, Canada

Meteoritic impacts under oxidizing surface conditions occur on both earth and Mars. Oxidative alteration of impact melt sheets is reported at several terrestrial impact structures including Manicouagan, West Clearwater Lake, and the Ries Basin. A number of studies have advocated that a significant fraction of Martian soil may consist of erosional products of oxidatively altered impact melt sheets. If so, the signature of the Fe-bearing mineralogies formed by the process may be present in visible and near infrared reflectivity data for the Martian surface. Of concern is what mineral assemblages form in impact melt sheets produced under oxidizing conditions and what their spectral signatures are. Spectral and Moessbauer data for 19 powder samples of impact melt rock from Manicouagan Crater are reported. Results show for naturally occurring materials that composite hematite-pyroxene bands have minima in the 910-nm region. Thus many of the anomalous Phobos-2 spectra, characterized by a shallow band minimum in the near-IR whose position varies between approximately 850 and 1000 nm, can be explained by assemblages whose endmembers (hematite and pyroxene) are accepted to be present on Mars. Furthermore, results show that a mineralogically diverse suite of rocks can be generated at essentially constant composition, which implies that variations in Martian surface mineralogy do not necessarily imply variations in chemical composition.

Morris, R. V.↗

NASA NTRS1992

Lunar resources: Oxygen from rocks and soil

The first set of hydrogen reduction experiments to use actual lunar material was recently completed. The sample, 70035, is a coarse-grained vesicular basalt containing 18.46 wt. percent FeO and 12.97 wt. percent TiO2. The mineralogy includes pyroxene, ilmenite, plagioclase, and minor olivine. The sample was crushed to a grain size of less than 500 microns. The crushed basalt was reduced with hydrogen in seven tests at temperatures of 900-1050 C and pressures of 1-10 atm for 30-60 minutes. A capacitance probe, measuring the dew point of the gas stream, was used to follow reaction progress. Experiments were also conducted using a terrestrial basalt similar to some lunar mare samples. Minnesota Lunar Simulant (MLS-1) contains 13.29 wt. percent FeO, 2.96 wt. percent Fe2O3, and 6.56 wt. percent TiO2. The major minerals include plagioclase, pyroxene, olivine, ilmenite, and magnetite. The rock was ground and seived, and experiments were run on the less than 74- and 500-1168-micron fractions. Experiments were also conducted on less than 74-micron powders of olivine, pyroxene, synthetic ilmenite, and TiO2. The terrestrial rock and mineral samples were reduced with flowing hydrogen at 1100 C in a microbalance furnace, with reaction progress monitored by weight loss. Experiments were run at atmospheric pressure for durations of 3-4 hr. Solid samples from both sets of experiments were analyzed by Mossbauer spectroscopy, petrographic microscopy, scanning electron microscopy, tunneling electron microscopy, and x-ray diffraction. Apollo 17 soil 78221 was examined for evidence of natural reduction in the lunar environment. This sample was chosen based on its high maturity level (I sub s/FeO = 93.0). The FeO content is 11.68 wt. percent and the TiO2 content is 3.84 wt. percent. A polished thin section of the 90-150 micron size fraction was analyzed by petrographic microscopy and scanning electron microscopy.

Allen, C. C.↗

NASA NTRS1992

Location of nanophase Fe-oxides in palagonitic soils: Implication for Martian pigments

Palagonitic materials from Mauna Kea, Hawaii, were identified as Mars analogs based on their spectral and magnetic properties. These materials probably resulted from hydrothermal alteration during eruption of the volcano and/or from weathering under ambient conditions. The reflectance spectra of the Mars surface obtained by Earth-based telescopes and the reflectance spectra of analogs obtained in the laboratory show features due to electronic transitions of Fe(III) in oxide particles that range in size from nanometer (nanophase) to micrometer sized or larger. The presence of Fe(III) suggests oxidizing conditions during the alteration process in Mars that may have occurred in the past or during a slow ongoing process. Two naturally altered basaltic samples from Hawaii (HWMK12 and HWMK13) and a laboratory-altered (PH-13-DCGT2) basaltic glass similar in elemental composition to the above two samples was examined. All three samples exhibited spectral characteristics similar to martian bright-region spectra. Chemical and mineralogical changes occurring at the surface of these basalts were studied in order to understand the basis for their Mars-like properties. The spectral properties of the three samples were examined after the removal of Fe oxides by chemical extractants.

Golden, D. C.↗