Engineering topics

Morris, D. E.

Publications and source records attributed to Morris, D. E..

10 records

NASA NTRS1994

Static and Dynamic Friction Behavior of Candidate High Temperature Airframe Seal Materials

The following report describes a series of research tests to evaluate candidate high temperature materials for static to moderately dynamic hypersonic airframe seals. Pin-on-disk reciprocating sliding tests were conducted from 25 to 843 C in air and hydrogen containing inert atmospheres. Friction, both dynamic and static, was monitored and serves as the primary test measurement. In general, soft coatings lead to excessive static friction and temperature affected friction in air environments only.

Dellacorte, C.↗

NASA NTRS1989

Limits on an optical pulsar in supernova 1987A

Since March 1987 the optical flux from supernova 1987A for periodic pulsations has been sought. As of August 1988, after 38 separate observations, no pulsar has been detected. The typical upper limit placed on the pulsed fraction optical light from the supernova is 0.0002, for pulse frequencies in the range 0.03-5000 Hz. The best limit on the pulsed fraction of supernova light is 7 x 10 to the -6th, on January 22, 1988. On August 28, 1988 the faintest limit for the magnitude of the pulsar, dimmer than 20th mag is reached. These limits are based on Fourier transforms of up to 67 million points, covering a range of spindown rates.

Pennypacker, C. R.↗

NASA NTRS1989

Submillisecond optical pulsar in supernova 1987A

An optical pulsar with frequency f = 1,968,629 Hz has been detected at the location of supernova 1987A in the LMC. The brightness of the pulsed light increased from magnitude 19 to 18 during a 7-hr observation period starting on 18.1 January 1987 UT. The frequency of the pulsar during this same period varied in a nearly sinusoidal manner, with an amplitude of 1.5 x 10 to the -3rd Hz and a period of 8 hr. If this is interpreted as the result of a binary orbit, it suggests that there may be a Jupiter-size object orbiting the pulsar at a distance of 10 to the 6th km.

Kristian, J.↗

NASA NTRS1986

Alkane-Based Urethane Potting Compounds

New low viscosity urethanes easily mixed, molded, and outgassed. Alkane-based urethanes resist hydrolysis and oxidation and have excellent dielectric properties. Low-viscosity alkane-based urethane prepolymer prepared by one-step reaction of either isophorone diisocyanate or methyl-bis (4-cyclohexyl isocyanate) with hydrogenated, hydroxy-terminated polybutadiene (HTPBD).

Morris, D. E.↗

NASA NTRS1985

Calculations for cosmic axion detection

Calculations are presented, using properly nomalized couplings and masses for Dine-Fischler-Srednicki axions, of power rates and signal temperatures for axion-photon conversion in microwave cavities. The importance of the galactic-halo axion line shape is emphasized. Spin-coupled detection as an alternative to magnetic-field-coupled detection is mentioned.

Krauss, L.↗

NASA NTRS1983

Development of low viscosity alkane-based urethane for connector potting applications

Two series of saturated hydrocarbon-based urethanes were prepared with isophorone diisocyanate and one series with methyl bis (4-cyclohexyl isocyanate). The urethanes with molecular weights as great as 2500 had viscosities low enough and a working life long enough to be used in potting, molding, and coating applications. Specimens were prepared and mechanical properties such as hardness, tensile strength elongation, and tear strength were determined. Thermomechanical properties (glass transition and expansion coefficient) and thermogravimetric properties were determined.

Morris, D. E.↗

NASA NTRS1983

Stable Polyurethane Coatings for Electronic Circuits

Alkane-based polyurethanes resist deterioration while maintaining good dielectric properties. Weight loss after prolonged immersion in hot water far less for alkane-based polyurethanes than for more common ether based polyurethanes, at any given oxygen content. Major uses of polyurethanes are as connector potting materials and conformal coatings for printed circuit boards.

Morris, D. E.↗

NASA NTRS1981

Development of urethane coating and potting material with improved hydrolytic and oxidative stability

A series of saturated hydrocarbon based urethanes was prepared and characterized for hydrolytic and oxidative stability. A series of ether based urethanes was used as a basis for comparison. The alkane base urethanes were found to be hydrolytically and oxidatively stable and had excellent electrical properties. The alkane based materials absorbed little or no water and were reversion resistant. There was little loss in hardness or weight when exposed to high temperature and humidity. Dielectric properties were excellent and suffered little adverse effects from the high temperature/humidity conditions. The alkane based urethanes were not degraded by ozone exposure.

Morris, D. E.↗

NASA NTRS1973

Polymerizable disilanols having in-chain perfluoroalkyl groups

Disilanols containing in-chain perfluoroalkyl and aromatic groups and the process by which they were prepared are discussed. The disilanols, when reacted with a diaminosilane and cured, produce polymeric material resistant to hydrocarbon fuels and stable at elevated temperatures.

Patterson, W. J.↗

NASA NTRS1972

Synthesis of temperature and solvent-resistant polymers

Development of silicone polymers, polyimides, and polyisocyanurates for use as insulation, coatings, or adhesives under adverse environmental conditions is discussed. Chemical structure of the organic compounds is presented. Physical and mechanical properties of the compounds are analyzed.

Webster, J. A.↗