Engineering Papers⌕ Search

Engineering topics

Moody, J. D.

Publications and source records attributed to Moody, J. D..

36 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The Scattered Light Time-history Diagnostic suite at the National Ignition Facility

The Scattered Light Time-history Diagnostic (SLTD) is being implemented at the National Ignition Facility (NIF) to greatly expand the angular coverage of absolute scattered-light measurements for direct- and indirect-drive inertial confinement fusion (ICF) experiments. The SLTD array will ultimately consist of 15 units mounted at a variety of polar and azimuthal angles on the NIF target chamber, complementing the existing NIF backscatter suite. Each SLTD unit collects and diffuses scattered light onto a set of three optical fibers, which transport the light to filtered photodiodes to measure scattered light in different wavelength bands: stimulated Brillouin scattering (350 nm–352 nm), stimulated Raman scattering (430 nm–760 nm), and ω/2 (695 nm–745 nm). SLTD measures scattered light with a time resolution of ~1 ns and a signal-to-noise ratio of up to 500. Currently, six units are operational and recording data. Measurements of the angular dependence of scattered light will strongly constrain models of laser energy coupling in ICF experiments and allow for a more robust inference of the total laser energy coupled to implosions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Low mode implosion symmetry sensitivity in low gas-fill NIF cylindrical hohlraums

Achieving an efficient capsule implosion in National Ignition Facility indirect-drive target experiments requires symmetric hohlraum x-ray drive for the duration of the laser pulse. This is commonly achieved using two-sided two-cone laser irradiation of cylindrical hohlraums that, in principle, can zero the time average of all spherical harmonic asymmetry modes <6 as well as the time dependence of the usually dominant mode 2. In practice, experimental evidence indicates that maintaining symmetric drive becomes limited late in the pulse due to the inward expansion of the hohlraum wall and outward expansion of the capsule ablator plasmas impairing the propagation of the inner-cone laser beams. This effect is enhanced in hohlraums employing low gas-fill, now used almost exclusively as these provide the highest performing implosions and reduce Stimulated Brillouin and Raman backscatter losses, since the gas plasma provides less back pressure to limit blow-in of the hohlraum wall and capsule ablator plasmas. In order to understand this dynamic behavior, we combined multi-keV X-ray imaging of the wall and imploded fuel plasmas as we changed a single parameter at a time: hohlraum gas-fill, laser outer cone picket energy, radius of high density carbon capsules used, and laser beam polar and azimuthal pointing geometry. In this work, we developed a physics-based multi-parameter experimental scaling to explain the results that extend prior scalings and compare those to radiation hydrodynamic simulations to develop a more complete picture of how hohlraum, capsule, and laser parameters affect pole vs equator drive symmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Laser transport and backscatter in low-density SiO 2 and Ta2O 5 foams

Experiments using a single 527 nm wavelength beam interacting with sub- and supercritical density SiO 2 and Ta 2 O 5 foams examined laser propagation and backscatter from laser–plasma instabilities such as Stimulated Brillouin Scattering (SBS). Two densities of each material were examined, and multiple diagnostics were used to characterize the propagation and backscatter. For 5 mg/cc SiO 2 (n e /n c = 0.375), the laser propagation distance was well approximated by treating the foam as a gas. However, for the 2 mg/cc SiO 2 foam (n e /n c = 0.15), the same model over-predicts the propagation distance by ~40%. Furthermore, existing analytical theories on propagation through subcritical foams were able to account for this difference. The laser heat wave propagated ~1/2 as far in Ta 2 O 5 than SiO 2 foams with similar electron density. We showed that this difference is due to the increased radiation losses in the higher Z foam. The fraction of backscattered light scales linearly with incident laser intensity for the range of intensities examined. Ta 2 O 5 foams had significantly lower levels of backscatter (1–3%) than the SiO 2 (4–8%), which is consistent with estimates of large Landau damping due to the presence of the oxygen atoms. The measured fraction of SBS backscattered laser energy for a 2 mg/cc SiO 2 foam shot was ~4 times lower than predicted by simulations assuming a gas-like foam. We found that we needed to assume increased ion heating such that T i /T e ~1.2–1.5 in the plasma to agree with the measured SBS reflectivity. Analytical models of laser-heated foams predict preferential heating of the ions as has been observed in previous experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Sputtered Au–Ta films with tunable electrical resistivity

Gold–tantalum alloy films are attractive for hohlraums used in indirect drive magnetized inertial confinement fusion. A high electrical resistivity of over ~100 µΩ cm at cryogenic temperatures is an essential requirement for allowing an externally imposed pulsed magnetic field to soak through a hohlraum and magnetize the fusion fuel. In this work, we systematically study properties of Au–Ta alloy films in the entire compositional range from pure Au to pure Ta with thicknesses up to 30 µm. These films are made by direct current magnetron co-sputtering on planar substrates. Films are characterized by a combination of high-energy ion scattering, x-ray diffraction, electron microscopy, nanoindentation, and electrical transport measurements. Results show that an alloy with ~80 at.% of Ta forms a metallic glass exhibiting a maximum electrical resistivity of ~300 µΩ cm with a weak temperature dependence in the range of 5–400 K. The deposition of a film with ~80 at.% of Ta onto a sphero-cylindrical substrate for hohlraum fabrication is also demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A novel method to measure ion density in ICF experiments using x-ray spectroscopy of cylindrical tracers

The indirect drive approach to inertial confinement fusion has undergone important advances in the past few years. Improvements in temperature and density diagnostic methods are leading to more accurate measurements of the plasma conditions inside the Hohlraum and therefore to more efficient experimental designs. The implementation of dot spectroscopy has proven to be a versatile approach to extracting space- and time-dependent electron temperatures. In this method, a microdot of a mid-Z material is placed inside the Hohlraum and its K-shell emission spectrum is used to determine the plasma temperature. However, radiation transport of optically thick lines acting within the cylindrical dot geometry influences the outgoing spectral distribution in a manner that depends on the viewing angle. This angular dependence has recently been studied in the high energy density regime at the OMEGA laser facility, which allowed us to design and benchmark appropriate radiative transfer models that can replicate these geometric effects. By combining these models with the measurements from the dot spectroscopy experiments at the National Ignition Facility, we demonstrate here a novel technique that exploits the transport effects to obtain time-resolved measurements of the ion density of the tracer dots, without the need for additional diagnostics. Furthermore, we find excellent agreement between experiment and simulation, opening the possibility of using these geometric effects as a density diagnostic in future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Foam-lined hohlraum, inertial confinement fusion experiments on the National Ignition Facility

Experiments on the National Ignition Facility (NIF) to study hohlraums lined with a 20-mg/cc 400-μm-thick Ta 2 O 5 aerogel at full scale (hohlraum diameter = 6.72 mm) are reported. Driven with a 1.6-MJ, 450-TW laser pulse, the performance of the foam liner is diagnosed using implosion hot-spot symmetry measurements of the high-density carbon (HDC) capsule and measurement of inner beam propagation through a thin-wall 8-μm Au window in the hohlraum. Results show an improved capsule performance due to laser energy deposition further inside the hohlraum, leading to a modest increase in x-ray drive and reduced preheat due to changes in the x-ray spectrum when the foam liner is included. In addition, the outer cone bubble uniformity is improved, but the predicted improvement in inner beam propagation to improve symmetry control is not realized for this foam thickness and density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Transient magnetic field diffusion considerations relevant to magnetically assisted indirect drive inertial confinement fusion

We report application of a magnetic field to an indirect drive inertial confinement fusion target requires diffusion of the field through the high-Z and electrically conducting Hohlraum. The onset of the external field generates eddy currents in the Hohlraum wall that result in (1) a reduction of the peak field at the capsule, (2) heating of the Hohlraum wall through Ohmic dissipation, and (3) wall movement due to the inward force from the eddy current interacting with the field. Heating of the wall causes an increase in blackbody radiation which can preheat the capsule and frozen deuterium–tritium fuel, while wall motion leads to potential misalignment of the lasers at the Hohlraum wall. Limiting these detrimental effects sets requirements on the tolerable magnitude of each effect. We present a nonlinear model for B-field diffusion through an infinitely long thin-walled cylinder with a temperature dependent resistivity, to show that a 15 μm thick wall of pure gold fails to meet these requirements. A new Hohlraum material made from an alloy of Au and Ta has a measured resistivity of ≥60 times that of Au and is shown with the nonlinear model to meet the requirements for magnetization. We compare the nonlinear model to simulations of the actual Hohlraum target using a finite element code which includes temperature-dependent Hohlraum resistivity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Evidence of restricted heat transport in National Ignition Facility Hohlraums

We present experimental evidence of restricted electron thermal conduction in the high-Z coronal plasma regions of laser-driven Hohlraums on the National Ignition Facility. Four separate measurements, three of which are direct observations of Hohlraum dynamics, corroborate this finding. (1) The velocity of the coronal plasma ablated and heated by the outer-cone laser beams is determined by time-dependent imaging of the gold plasma plume, or “bubble.” The velocities of the incoming plume (perpendicular to the Hohlraum axis) are consistent with high-fidelity 2D radiation-hydrodynamic simulations using flux-limited thermal electron conduction with a flux multiplier f = 0.03. Simulations using f = 0.15, which is very nearly classical Spitzer–Härm transport, predict plume velocities slower than measured. (2) Specific features in time-resolved images of the Hohlraum wall at an angle of 19° are also more consistent with f = 0.03 simulations compared to f = 0.15. (3) Spectroscopic tracers were added to the Hohlraum wall in the outer-beam bubble region. The ratios of hydrogen-like to helium-like line emission are sensitive to the electron temperature of the bubble. The hydrogen-like to helium-like ratios extracted from the time-integrated spectra of manganese and cobalt tracers from two observation angles are consistent with f = 0.03 and not with f = 0.15. (4) The time of peak capsule emission, or “bang time,” an integrated measurement, is also more consistent with f = 0.03 than with f = 0.15. Overall, while these findings do not identify the causes of restricted thermal conduction in Hohlraums, they motivate future experiments to test specific hypotheses and focus on model development in the regions of the plasma exhibiting restricted transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Experimental demonstration of the reduced expansion of a laser-heated surface using a low density foam layer, pertaining to advanced hohlraum designs with less wall-motion

The ablative expansion of laser-heated materials is important for determining how hohlraum cavities can be utilized for inertial confinement fusion. The utility of a low-density foam layer to reduce the density of the expanding heated hohlraum wall is demonstrated here in a series of experiments on the National Ignition Facility. X-ray radiography measurements of the expanding foam-lined Au wall in low aspect-ratio cylindrical geometry are used to compare the impact of Au-doped CH and Ta 2 O 5 foams between 10 and 40 mg/cc on the wall expansion. HYDRA Simulations are used to estimate the x-ray transmission at the 1/4 nc surface, which is important in understanding the absorption of laser light by the plasma. These demonstrate for the first time that a foam layer reduces the expansion of a hohlraum-like target and illustrate that the interplay between the expanding foam plasma and the shock reflected by the hohlraum wall is critical in optimizing foam-liner parameters to achieve the maximum time for a symmetric drive on a capsule.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Hot-electron generation at direct-drive ignition-relevant plasma conditions at the National Ignition Facility

Laser–plasma interaction instabilities can be detrimental for direct-drive inertial confinement fusion by generating high-energy electrons that preheat the target. Moreover, an experimental platform has been developed and fielded on the National Ignition Facility to investigate hot-electron production from laser–plasma instabilities at direct-drive ignition-relevant conditions. The radiation-hydrodynamic code DRACO has been used to design planar-target experiments that generate plasma and interaction conditions comparable to direct-drive ignition designs: I L ~10 15 W/cm 2 , T e > 3 keV, and density-gradient scale lengths of L n ~ 600 μ m in the quarter-critical density region. The hot-electron properties were inferred by comparing the experimentally observed hard x-ray spectra to Monte Carlo simulations of hard x-ray emission from hot electrons depositing energy in the target. Hot-electron temperatures of ~40 keV to 60 keV and the fraction of laser energy converted to hot electrons of ~0.5% to 5% were inferred in plastic targets for laser intensities at the quarter-critical density surface of (~4 to 14) × 10 14 W/cm 2 . The use of silicon ablators was found to mitigate the hot-electron preheat by increasing the threshold laser intensity for hot-electron generation from ~3.5 × 10 14 W/cm 2 in plastic to ~6 × 10 14 W/cm 2 in silicon. The overall hot-electron production is further reduced in silicon ablators when the intensity threshold is exceeded.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Stimulated Raman scattering mechanisms and scaling behavior in planar direct-drive experiments at the National Ignition Facility

Stimulated Raman scattering (SRS) has been investigated comprehensively in planar-geometry experiments at the National Ignition Facility at conditions relevant to the corona of inertial con finement fusion (ICF) ignition-scale direct-drive targets. These experiments at measured electron temperatures of 4 to 5 keV, simulated density scale lengths Ln of 400 to 700 um, and laser intensities at the quarter-critical density of up to 1.5 x 10 15 W/cm 2 have determined SRS thresholds and the scaling behavior of SRS for various beam geometries. Several SRS mechanisms, including saturated absolute SRS near the quarter-critical density and additional SRS, including near-backscatter or sidescatter at lower densities, have been identi fied. Correlation of time-dependent SRS at densities ~0.15 to 0.21 of the critical density with hot-electron signatures, as well as the magnitudes of these signatures across different experiments, is observed. Additional modeling work is needed to de nitively identify the density region in which hot electrons are generated, and will guide SRS and hot-electron preheat mitigation strategies for direct-drive-ignition designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Proton deflectometry of a capacitor coil target along two axes

A developing application of laser-driven currents is the generation of magnetic fields of picosecond–nanosecond duration with magnitudes exceeding $B=10~\text{T}$. Single-loop and helical coil targets can direct laser-driven discharge currents along wires to generate spatially uniform, quasi-static magnetic fields on the millimetre scale. Here, we present proton deflectometry across two axes of a single-loop coil ranging from 1 to 2 mm in diameter. Comparison with proton tracking simulations shows that measured magnetic fields are the result of kiloampere currents in the coil and electric charges distributed around the coil target. Using this dual-axis platform for proton deflectometry, robust measurements can be made of the evolution of magnetic fields in a capacitor coil target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Study of laser-driven magnetic fields with a continuous wave Faraday rotation diagnostic

Magnetic fields driven by a laser in coil targets were studied for laser energies of ~25 J and two pulse durations of 2.8 ns and 70 ps. Axial magnetic fields in the coils were measured by continuous wave Faraday rotation diagnostics. The diagnostics indicated magnetic fields of 6–14 T in the coil and currents of 10–20 kA. Magnetic fields were compared for similar laser targets, focusing conditions, and laser energies. A 30-times increase in the intensity of the laser beam by reducing the pulse duration resulted in an increase in the magnetic field and current by a factor of 2. The relaxation time of the magnetic pulse was on the sub-microsecond scale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Laser intensity scaling of the magnetic field from a laser-driven coil target

In this paper, we report on the first direct voltage and current measurements from a laser-generated magnetic field coil target. The magnetic field was observed to scale with the laser intensity as $B ∝ \mathcal{I}^{0.66±0.13}_\text{laser}$. This scaling relation can be derived from the measured voltage approximated by the laser-heated plasma electron temperature $T_e$. The experiments used a 1053 nm laser with pulse lengths ranging from 0.5 to 20 ns and intensities ranging from 10 9 to 10 14 W/cm 2 to generate an electric potential that drives current through the coil. We show that the behavior of the coil can be described with a lumped-element circuit model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Understanding ICF hohlraums using NIF gated laser-entrance-hole images

The newly available ns-gated laser-entrance-hole (LEH) imager on the National Ignition Facility provides routine, non-perturbative measurements of the x-ray emission from laser-heated plasmas inside the hohlraum as viewed at 19° to the hohlraum axis through one of its LEHs. Multiple images are acquired for a series of times and filter-selected x-ray energy bands within a single shot. The images provide time dependent data on phenomena including the effective radius of the LEH, the length of the gold-plasma “bubble” evolving off the interior wall surface heated by the outer beams, the evolving radius of the x-ray heated hohlraum wall, and the radius of the ablation front of the fusion capsule. Here, these measurements are explained and illustrated with sample data. These techniques are then applied to understand hohlraum behavior as a function of gas fill. For hohlraums with helium gas fill densities of 0.15 to 0.30 mg/cm 3 , synthetic images computed from simulations agree well with experimental gated LEH images when an inhibited heat transport model [Jones et al., Phys. Plasmas 24, 056312 (2017)] is used. This model can be adjusted to reproduce the expansion rate of the laser-heated plasma bubble in such a way as to improve agreement with the images. At the higher 0.6 mg/cc gas fill, the experimental images show more pronounced 3D features, resulting in slightly less good agreement with the 2D simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗