Engineering topics

Molins, Sergi

Publications and source records attributed to Molins, Sergi.

11 records

DOE OSTI2025

Permeate fluxes from desalination of brines and produced waters: A reactive transport modeling study

The increasing interest in the use of membrane systems to desalinate inland brackish water, agricultural drainage, and industrially produced wastewater demands improved means of predicting desalination system performance under variable feedwater compositions. The interaction among water flow, solute transport, and chemical composition in these systems impacts permeate flux evolution. Here, an established multicomponent reactive transport simulator that accounts for these coupled processes is applied to compute osmotic pressure and permeate fluxes in reverse osmosis (RO) systems. The model is first validated by predicting permeate fluxes for a set of benchtop crossflow experiments subject to a range of feed flow rates and compositions, under fouling and non-fouling conditions. Results compare favorably with measured data that show that solutions with similar total dissolved solids concentrations but different compositions result in different permeate fluxes. The model is then applied to predict permeate fluxes from the desalination of produced waters using a commercial spiral wound RO module. For NaCl-dominant brines, at total dissolved salt concentrations (TDS) below about 70 g/L, permeate fluxes are inversely proportional to water mole fraction as the latter is a reasonable approximation of water activity (i.e. ideal mixing). In the case of Ca–Cl-, Na–CO3- and Na–SO4-dominant brines below about 70 g/L TDS, this relationship does not hold as well and tends to overpredict osmotic pressure and thus underpredict permeate fluxes. However, the opposite becomes true at higher TDS values for typical produced waters. The scaling potential of these waters is also computed by allowing the precipitation of minerals above their saturation limit on the RO membrane. This work demonstrates how reactive transport models developed for the analysis of waters from geological systems can be extended to improve process design, optimization, and control in desalination systems from produced waters and beyond.

Molins, Sergi↗

DOE OSTI2024

A multiphysics coupling framework for exascale simulation of fracture evolution in subsurface energy applications

Predicting the evolution of fractured media is challenging due to coupled thermal, hydrological, chemical and mechanical processes that occur over a broad range of spatial scales, from the microscopic pore scale to field scale. We present a software framework and scientific workflow that couples the pore scale flow and reactive transport simulator Chombo-Crunch with the field scale geomechanics solver in GEOS to simulate fracture evolution in subsurface fluid-rock systems. This new multiphysics coupling capability comprises several novel features. An HDF5 data schema for coupling fracture positions between the two codes is employed and leverages the coarse resolution of the GEOS mechanics solver which limits the size of data coupled, and is, thus, not taxed by data resulting from the high resolution pore scale Chombo-Crunch solver. The coupling framework requires tracking of both before and after coarse nodal positions in GEOS as well as the resolved embedded boundary in Chombo-Crunch. We accomplished this by developing an approach to geometry generation that tracks the fracture interface between the two different methodologies. The GEOS quadrilateral mesh is converted to triangles which are organized into bins and an accessible tree structure; the nodes are then mapped to the Chombo representation using a continuous signed distance function that determines locations inside, on and outside of the fracture boundary. The GEOS positions are retained in memory on the Chombo-Crunch side of the coupling. The time stepping cadence for coupled multiphysics processes of flow, transport, reactions and mechanics is stable and demonstrates temporal reach to experimental time scales. The approach is validated by demonstration of 9 days of simulated time of a core flood experiment with fracture aperture evolution due to invasion of carbonated brine in wellbore-cement and sandstone. We also demonstrate usage of exascale computing resources by simulating a high resolution version of the validation problem on OLCF Frontier.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

Approaches for the Simulation of Coupled Processes in Evolving Fractured Porous Media Enabled by Exascale Computing

Models have historically represented fractured porous media with continuum descriptions that characterize the media using bulk parameters. The impact of small-scale features is not captured in these models, although they may be controlling the performance of subsurface applications. Pore-scale models can simulate processes in small-scale features by representing the pore space geometry explicitly but are computationally expensive for large domains. The alternative multiscale approach entails the combination of pore-scale and continuum-scale descriptions in a single framework. We use Chombo-Crunch, a computational capability that discretizes complex geometries with an adaptive, embedded boundary method to contrast these two approaches. Chombo-Crunch takes advantage of recent computational performance and memory bandwidth improvements resulting from the emergence of exascale computing resources. These combined improvements enable the efficient simulation of reactive transport in fractured media with a high degree of fidelity and the ability to capture the control small-scale processes exert on the overall medium evolution.

42 ENGINEERING↗

DOE OSTI2024

Integrating Tide‐Driven Wetland Soil Redox and Biogeochemical Interactions Into a Land Surface Model

Abstract Redox processes, aqueous and solid‐phase chemistry, and pH dynamics are key drivers of subsurface biogeochemical cycling and methanogenesis in terrestrial and wetland ecosystems but are typically not included in terrestrial carbon cycle models. These omissions may introduce errors when simulating systems where redox interactions and pH fluctuations are important, such as wetlands where saturation of soils can produce anoxic conditions and coastal systems where sulfate inputs from seawater can influence biogeochemistry. Integrating cycling of redox‐sensitive elements could therefore allow models to better represent key elements of carbon cycling and greenhouse gas production. We describe a model framework that couples the Energy Exascale Earth System Model (E3SM) Land Model (ELM) with PFLOTRAN biogeochemistry, allowing geochemical processes and redox interactions to be integrated with land surface model simulations. We implemented a reaction network including aerobic decomposition, fermentation, sulfate reduction, sulfide oxidation, methanogenesis, and methanotrophy as well as pH dynamics along with iron oxide and iron sulfide mineral precipitation and dissolution. We simulated biogeochemical cycling in tidal wetlands subject to either saltwater or freshwater inputs driven by tidal hydrological dynamics. In simulations with saltwater tidal inputs, sulfate reduction led to accumulation of sulfide, higher dissolved inorganic carbon concentrations, lower dissolved organic carbon concentrations, and lower methane emissions than simulations with freshwater tidal inputs. Model simulations compared well with measured porewater concentrations and surface gas emissions from coastal wetlands in the Northeastern United States. These results demonstrate how simulating geochemical reaction networks can improve land surface model simulations of subsurface biogeochemistry and carbon cycling.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Understanding the hydrological response of a headwater-dominated catchment by analysis of distributed surface–subsurface interactions

Abstract We computationally explore the relationship between surface–subsurface exchange and hydrological response in a headwater-dominated high elevation, mountainous catchment in East River Watershed, Colorado, USA. In order to isolate the effect of surface–subsurface exchange on the hydrological response, we compare three model variations that differ only in soil permeability. Traditional methods of hydrograph analysis that have been developed for headwater catchments may fail to properly characterize catchments, where catchment response is tightly coupled to headwater inflow. Analyzing the spatially distributed hydrological response of such catchments gives additional information on the catchment functioning. Thus, we compute hydrographs, hydrological indices, and spatio-temporal distributions of hydrological variables. The indices and distributions are then linked to the hydrograph at the outlet of the catchment. Our results show that changes in the surface–subsurface exchange fluxes trigger different flow regimes, connectivity dynamics, and runoff generation mechanisms inside the catchment, and hence, affect the distributed hydrological response. Further, changes in surface–subsurface exchange rates lead to a nonlinear change in the degree of connectivity—quantified through the number of disconnected clusters of ponding water—in the catchment. Although the runoff formation in the catchment changes significantly, these changes do not significantly alter the aggregated streamflow hydrograph. This hints at a crucial gap in our ability to infer catchment function from aggregated signatures. We show that while these changes in distributed hydrological response may not always be observable through aggregated hydrological signatures, they can be quantified through the use of indices of connectivity.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

A reduced-order model of concentration polarization in reverse osmosis systems with feed spacers

Feed spacers in reverse osmosis systems generate complex fluid flows that limit computational fluid dynamics (CFD) simulations to small length and time scales. That limits our ability to simulate mineral scaling and other membrane fouling phenomena, which occur over longer length and time scales. Thus motivated, we develop a reduced model that replaces the CFD simulation of the velocity field with an analytical model that mimics spacers. This focuses the remaining numerical effort on simulating the advection–diffusion equation governing solute transport. We motivate and validate the model with CFD simulations and bench-scale experiments of spacer filaments in three different arrangements, including cases of unsteady vortex shedding. We show that the model produces a roughly 10,000-fold speedup compared to CFD, and accurately reproduces CFD predictions of not only the average and maximum concentrations, but also the local concentration distribution along the membrane. Here, we also demonstrate the model for simulating a feed channel with a length-to-height ratio of 200. The model provides a simple testbed for exploratory studies of multispecies transport, precipitation, and membrane fouling phenomena for which simulating spacers is often prohibitive.

Computational fluid dynamics↗

DOE OSTI2023

Model simulations of Plum Island Ecosystems LTER low marsh site using ELM-PFLOTRAN

Model simulations using the E3SM Land Model (ELM) coupled to the PFLOTRAN reactive transport model via the Alquimia interface. The simulations were conducted for a tidal salt marsh at the Plum Island Ecosystems LTER near Rowley, Massachusetts, USA. Model simulations were forced using site-specific tidal cycles and salinity, and the simulations used a biogeochemical reaction network including aerobic decomposition, sulfate reduction, iron reduction, and methanogenesis. Model outputs include simulated carbon stocks, carbon dioxide and methane fluxes, and porewater concentrations of key solutes related to sulfur, iron, and carbon cycling. The model simulations included a saline simulation (with tidal sulfate inputs), a fresh simulation (with low salinity and low sulfate inputs), and a saline simulation with lower vegetation productivity to represent the effect of salinity on vegetation. These simulations were conducted to demonstrate that a new model framework incorporating subsurface redox and biogeochemical interactions into a land surface model could reproduce measured surface greenhouse gas fluxes and biogeochemical dynamics in tidal marsh ecosystems, and to test whether including redox interactions in a land surface model would allow the model to resolve contrasts in biogeochemical cycling and greenhouse gas production between saline and freshwater wetlands.The data package includes gzipped tar archives (which can be expanded using standard tar and gzip utilities) of model outputs from three model configurations: saline subsurface and reduced vegetation productivity related to salinity; saline subsurface with vegetation productivity not reduced; and freshwater. Also included are code for the modified E3SM model, Alquimia interface, and PFLOTRAN reactive transport simulator in gzipped tar format; plain text parameter and configuration files; python code files for visualizing model output and defining model configurations; and model output, tide and salinity forcing, and configuration files in netCDF format. See the README.md file in the data package for a detailed description of all files contained in the package. All files are in netCDF (.nc), gzipped tar archive (.tar.gz or .tgz), or text (all other files).Updated: May 13, 2024. Model output, E3SM code, PFLOTRAN input files, and python codes for visualizing results were updated to reflect changes made for the manuscript revision. The updated archive reflects the code and model output from the final accepted manuscript. Changes included updated reaction parameters reflecting improved parameterization and additional comparisons with field measurements. E3SM code changes included better support for multiple grid cells and improved flow and transport parameterization.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Understanding the Hydrogeochemical Response of a Mountainous Watershed Using Integrated Surface‐Subsurface Flow and Reactive Transport Modeling

Abstract Climate change and other disturbances significantly impact hydrogeochemical exports from mountainous headwater catchments such as the Upper Colorado River Basin. Developing a mechanistic understanding of how the physical and chemical processes interact in time and space in an integrated manner is key to quantifying the future impacts of such disturbances. The hydrogeochemical response of a mountainous catchment in the 2010–2019 period is evaluated quantitatively using a high‐resolution model that simulates integrated hydrology, and transport and reactions for selected solutes and minerals. The model assumes that pyrite is present only at depth while calcite is distributed uniformly, and captures the observed C‐Q reasonably well. Distinct C‐Q dynamics are observed in an average (WY16), a wet (WY17), and a dry (WY18) water year. The model also quantifies the water fraction from surface, shallow and deep groundwater compartments using tracers, and suggests greater groundwater contributions to peak stream discharge in the dry WY18. Results demonstrate that calcium concentrations do not change significantly from year to year, while sulfate shows significant temporal variability. Pyrite dissolution is affected by the changing hydrological drivers where it is enhanced in the dry WY18; calcite dissolution supplements calcium dilution under high flow conditions. The model simulates the reaction hotspots controlled by hydrological conditions, and the spatially‐resolved results show that higher soil saturation and less snowpack occur earlier on the south‐facing side than on the north‐facing side. This is a first‐of‐its‐kind demonstration of a model that integrates hydrologic processes, including evapotranspiration, and reactive transport to enable a predictive understanding of hydrogeochemical exports.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

A Multicomponent Reactive Transport Model for Integrated Surface‐Subsurface Hydrology Problems

Abstract Despite the widespread use of integrated hydrology models in a variety of applications, consideration of multicomponent reactive transport is still not common. The implementation of these processes requires coupling transport at the surface‐subsurface interface and efficient solution of the non‐linear geochemical model that is consistent with the integrated hydrology solution. The Advanced Terrestrial Simulator provides a flexible multiphysics framework that facilitated this process. In this work, the integrated reactive transport process kernel (PK) was weakly coupled to the integrated hydrology PK. In turn, integrated transport and reactions were coupled using an operator splitting approach. This splitting enabled an explicit solution of the integrated transport problem, including a novel algorithm to calculate exchange fluxes across the surface‐subsurface interface and a point‐by‐point solution of the geochemical problem. Geochemical capabilities were added using well‐established external codes, but rather than using a custom interface to each, a generic interface was used that clearly specifies the variables and operations used by the chemistry PK. The implementation is demonstrated with two example simulations: transport of a tracer in a soil column as it saturates over time and water ponds on the surface and reactive transport in a hillslope driven by successive wet‐dry cycles that result in infiltration, runoff and exfiltration processes.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Investigation of Coupled Processes in Fractures and the Bordering Matrix via a Micro‐Continuum Reactive Transport Model

Abstract In multi‐mineral fractured rocks, the altered porous layer on the fracture surface resulting from preferential dissolution of the fast‐reacting minerals can have profound impacts on subsequent chemical‐physical alteration of the fractures. This study adopts the micro‐continuum approach to provide further understanding of reactive transport processes in the altered layer (AL), and mass exchanges with the bordering matrix and fracture. The modeling framework couples the Darcy‐Brinkman‐Stokes (DBS) solver in COMSOL Multiphysics and the geochemical modeling capability of CrunchFlow. Three‐dimensional steady state simulations with systematically varied chemical‐physical parameters of the AL were performed to examine the impacts of individual factors and processes. Our simulation results confirm previous observations that dissolution of the fast‐reacting mineral (i.e., calcite) is largely controlled by diffusion across the AL. We also show that dissolution of the slow‐reacting mineral (i.e., dolomite), which controls AL development and fracture enlargement, increases with surface area and has a complex dependence on different local rate‐limiting processes. In particular, advection can result in evident spatial variations in the local dissolution rates of dolomite, although it does not affect the bulk chemistry significantly. The difference in the spatial patterns between simulations with and without advection in the AL is more noticeable in the locations with smaller apertures, with up to 20% difference in local reaction rates. Therefore, it is important to include a full depiction of advection, diffusion, and reactions for accurately capturing local dynamics that control long‐term fracture evolution.

58 GEOSCIENCES↗

DOE OSTI2022

ATS (Advanced Terrestrial Simulator) integrated hydrology and reactive transport model output in Copper Creek, Colorado

This dataset is generated using the ATS (Advanced Terrestrial Simulator) model at Copper Creek, Colorado, the largest catchment in the East River watershed. ATS is an integrated hydrology and reactive transport model to simulate the Concentration-Discharge (C-Q) relationship, and is used to quantify the geochemical export and understand how watersheds respond to climate disturbances. Key hydrogeochemical variables, including discharge, precipitation, evapotranspiration, and geochemical concentrations, were simulated and output at a daily frequency at the Copper Creek outlet. A group of hydrology and geochemical model variables over the spatial domain are output at a bi-monthly frequency. The model used 1-km resolution daily frequency Daymet meteorological forcing, and mineral composition from previous studies. The simulations are performed on NERSC. The datasets include the input files for running the ATS (Advanced Terrestrial Simulator) simulation, including the mesh file, input script and geochemical model files. The output files from the ATS (Advanced Terrestrial Simulator) are the daily time-series discharge and geochemical concentration simulated at the outlet of Copper Creek, and the bi-monthly spatial output over the simulation domain.

54 ENVIRONMENTAL SCIENCES↗