Engineering Papers⌕ Search

Engineering topics

Mokhov, Nikolai

Publications and source records attributed to Mokhov, Nikolai.

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Radiation Shielding Analysis for the PIP-II Linac at Fermilab

The Proton Improvement Plan-II (PIP-II) [1] has been developed at Fermilab to provide powerful proton beams to the laboratory’s experiments. An 800-MeV superconducting linear accelerator—a centerpiece of the project—is currently under construction in Batavia, Illinois (USA). After completion, the superconducting linac will be the starting point for the 1.2 MW (Phase 1) and 2.4-MW (Phase 2) proton beam that is needed for the Long-Baseline Neutrino Facility (LBNF) at Fermilab [2]. Due to unavoidable loss of a fraction of the beam in the accelerator components, a certain level of radiation will be generated in the accelerator tunnel both during normal operation and at accidents. This work deals with radiation shielding design for the accelerator facility.

Rakhno, Igor↗
DOE OSTI2022

Second Generation Fermilab Main Injector 8 GeV Beamline Collimation Preliminary Design

The current Fermilab Main Injector 8 GeV beamline transverse collimation system was installed in 2006. Since then, proton beam intensities and rates have increased significantly. With the promise of even greater beam intensities and a faster repetition rate when the PIP-II upgrade completes later this decade, the current collimation system will be insufficient. Over the past 18 months, multiple collimation designs have been investigated, some more traditional and others novel. A preliminary design review was conducted and a design chosen. Work is underway to finalize the chosen design, prototype some of its novel components and procure parts for installation Summer 2023.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Optimization Studies for the Long-Baseline Neutrino Facility at Fermilab

The Deep Underground Neutrino Experiment and Long-Baseline Neutrino Facility (DUNE-LBNF) are under development at Fermilab since early 2010s [1]. At present, the work is being performed towards a comprehensive review conducted by US Department of Energy (DOE)-the Critical Decision 2 (CD-2)-that is planned to take place in the middle of 2022. The primary scientific objectives of DUNE are to carry out a comprehensive investigation of neutrino oscillations to test CP violation in the lepton sector, determine the ordering of the neutrino masses, and to test the three-neutrino paradigm (electron, muon and tau neutrino). The LBNF will provide a 120-GeV proton beam on a neutrino production target utilizing a new 800-MeV superconducting Linac which is expected to be completed in 2027 [2]. The neutrino beamline, which utilizes a target and horn systems, decay pipe, hadron absorber and other systems, is a core component of the LBNF. At present-as a result of numerous iterations-there exists an optimized design with a 1.5-m graphite target and focusing system consisting of three horns. Further optimization energy deposition and radiological calculations are performed towards CD-2 and beyond. This paper describes results of the most recent MARS15 [3] optimization studies.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Advanced assessment of beam-induced background at a muon collider

Renewed international interest in muon colliders motivates the continued investigation of the impacts of beam-induced background on detector performance. This continues the effort initiated by the Muon Accelerator Program and carried out until 2017. The beam-induced background from muon decays directly impacts detector performance and must be mitigated by optimizing the overall machine design, with particular attention paid to the machine detector interface region. In order to produce beam-induced background events and to study their characteristics in coordination with the collider optimization, a flexible simulation approach is needed. To achieve this goal we have chosen to utilize the combination of LineBuilder and Monte Carlo FLUKA codes. We report the results of beam-induced background studies with these tools obtained for a 1.5 TeV center of mass energy collider configuration. Good agreement with previous simulations using the MARS15 code demonstrates that our choice of tools meet the accuracy and performance requirements to perform future optimization studies on muon collider designs.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Monte Carlo Driven MDI Optimization at a Muon Collider

A Muon Collider represents a very interesting possibility for a future machine to explore the energy frontier in particle physics. However, to reach the needed luminosity, beam intensities of the order of 10⁹–10¹² muons per bunch are needed. In this context, the Beam-Induced Background must be taken into account for its effects on magnets and detector. Several mitigation strategies can however be conceived. In this view, it is of crucial importance to develop a flexible tool that allows to easily reconstruct the machine geometry in a Monte Carlo code, allowing to simulate in detail the interaction of muon decay products in the machine, while being able to change the machine optics itself to find the best configuration. In this contribution, a possible approach to such a purpose is presented, based on FLUKA for the Monte Carlo simulation and on LineBuilder for the geometry reconstruction. Results based on the 1.5 TeV machine optics developed by the MAP collaboration are discussed, as well as a first approach to possible mitigation strategies.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

A Flexible Tool for Beam Induced Background Simulations at a Muon Collider

A Muon Collider represents a very interesting possibility for a future machine to explore the energy frontier in particle physics.However, to reach the needed luminosity, beam intensities of the order of $10^{9-11}$ muons per bunch are needed. In this context, the Beam Induced Background must be taken into account for its effects on the magnets and on the detector. Several optimizations can be conceived with the aim to mitigate them. In this view, it is of crucial importance to develop a flexible tool that allows to easily reconstruct the machine geometry in a Monte Carlo code, allowing to simulate in detail the interaction of muon decay products in the machine, while being able to change the machine optics itself to find the best configuration.In this contribution, a possible approach to such a purpose is presented, based on FLUKA for the Monte Carlo simulation and on LineBuilder for the geometry reconstruction.First results for the 1.5TeV machine optics developed by the MAP collaboration are discussed in this paper.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗