Engineering topics
Publications and source records attributed to Milton, Martha E..
This viewgraph presentation describes the Deep Space Test Bed (DSTB), a balloon-borne device which can expose multiple payloads to the interplanetary Galactic Cosmic Ray environment on high altitude polar balloon flights. The DSTB is carried by National Scientific Balloon Facility (NSBF) Long Duration Balloons on polar flights so that its balloon-borne experiments can avoid geomagnetic cut-offs.
The DSTB Facility provides a new capability for the National Aeronautics and Space Administration s (NASA s) Space Radiation Shielding Project (SRSP). The objective of the DSTB is to provide a platform to conduct radiation shielding investigations in an environment more similar to deep space than most Low Earth orbits or is achievable at a particle accelerator. The DSTB provides a means to experimentally test radiation shielding effectiveness of various materials and to test the accuracy of radiation transport code predictions in the deep space cosmic ray environment more frequently and at a lower cost compared to space flight missions. New spectrometers, dosimeters and other techniques may be exercised and verified using the DSTB before space flight. The DSTB will be implemented through NASA s National Scientific Balloon Facility (NSBF) which provides polar balloon flights that lift science payloads to high altitude (120,000 A. (36.58km)) to escape much of the shielding effects of the Earth s atmosphere and magnetosphere. Polar flights are conducted through NSBF in coordination with the United States Polar Program. The DSTB will be launched on a Long Duration Balloon (LDB) from McMurdo, Antarctica (77.86 degrees south latitude) for circumpolar flights, nominally 20 days, traveling to the west and typically bounded between 73 to 82 degrees south latitude. Float altitudes for these balloons with payload are 115,000 to 130,000 feet (35.05 to 39.62km). The DSTB will be able to accommodate up to 20 investigations per flight. Annual flight opportunities are planned starting in December 2005. Balloon campaigns in Antarctica occur in December and January during the Austral summer. Since a key goal of the DSTB facility is to efficiently serve the varied needs of the radiation shielding community; it must be designed with a flexible architecture. By implementing the DSTB facility with NASA s balloon program, which operates under reduced formalities compared to space flight, the DSTB facility can adjust for different investigation priorities on successive flights. This flexibility in the DSTB will be applied at several levels; in the distribution of the shared resources for each flight; addressing the payload configuration on a system level for each flight; and utilizing a selection process for investigations that considers yearly flight opportunities as well as the possibility for repeated flights. This approach for operating the DSTB facility will allow it to handle a wide range of investigations.
This paper discusses the development and design of an experimental test cell for ground-based testing to provide requirements for the Spaceflight Holography Investigation in a Virtual Apparatus (SHIVA) experiment. Ground-based testing of a hardware breadboard set-up is being conducted at Marshall Space Flight Center in Huntsville, Alabama. SHIVA objectives are to test and validate new solutions of the general equation of motion of a particle in a fluid, including particle-particle interaction, wall effects, motion at higher Reynolds Number, and a motion and dissolution of a crystal moving in a fluid. These objectives will be achieved by recording a large number of holograms of particle motion in the International Space Station (ISS) glove box under controlled conditions, extracting the precise three- dimensional position of all the particles as a function of time, and examining the effects of all parameters on the motion of the particles. This paper will describe the mechanistic approach to enabling the SHIVA experiment to be performed in a ISS glove box in microgravity. Because the particles are very small, surface tension becomes a major consideration in designing the mechanical method to meet the experiments objectives in microgravity, To keep a particle or particles in the center of the test cell long enough to perform and record the experiment and to preclude contribution to particle motion, requires avoiding any initial velocity in particle placement. A Particle Injection Mechanism (PIM) designed for microgravity has been devised and tested to enable SHIVA imaging. Also, a test cell capture mechanism, to secure the test cell during vibration on a specially designed shaker table for the SHIVA experiment will be described. Concepts for flight design are also presented.
The Automated Fluid Interface System (AFIS) is an advanced development program aimed at becoming the standard interface for satellite servicing for years to come. The AFIS will be capable of transferring propellants, fluids, gasses, power, and cryogens from a tanker to an orbiting satellite. The AFIS program currently under consideration is a joint venture between the NASA/Marshall Space Flight Center and Moog, Inc. An engineering model has been built and is undergoing development testing to investigate the mechanism's abilities.