Engineering Papers⌕ Search

Engineering topics

Miller, James E.

Publications and source records attributed to Miller, James E..

At least 19 records

Two-Step Chemical Looping Cycle for Renewable NH 3 Production Based on Non-Catalytic Co 3 Mo 3 N/Co 6 Mo 6 N Reactions

A two-step solar thermochemical looping cycle based on Co 3 Mo 3 N/Co 6 Mo 6 N reduction/nitridation reactions offers a pathway for green NH 3 production that utilizes concentrated solar irradiation, H 2 O, and air as feedstocks. The NH 3 production cycle steps both derive process heat from concentrated solar irradiation and encompass 1) the reduction of Co 3 Mo 3 N in H 2 to Co 6 Mo 6 N and NH 3 ; and 2) nitridation of Co 6 Mo 6 N to Co 3 Mo 3 N with N 2 . Co 3 Mo 3 N reduction/nitridation reactions are examined at different H 2 and/or N 2 partial pressures and temperatures. NH 3 production is quantified in situ using liquid conductivity measurements coupled with mass spectrometry (MS). Solid-state characterization is performed to identify a surface oxygen layer that necessitates the addition of H 2 during cycling to prevent surface oxidation by trace amounts of O 2 . H 2 concentrations of > 5% H 2 /Ar and temperatures >500 °C are required to reduce Co 3 Mo 3 N to Co 6 Mo 6 N and form NH 3 at 1 bar. Complete regeneration of Co 3 Mo 3 N from Co 6 Mo 6 N is achieved at conditions of 700 °C under 25–75% H 2 /N 2 . H 2 pressure-swings are observed to increase NH 3 production during Co 3 Mo 3 N reduction. In conclusion, the results represent the first comprehensive characterization of and definitive non-catalytic production of NH 3 via chemical looping with metal nitrides and provide insights for technology development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrically enhanced thermochemical cycles for hydrogen generation

In two-step metal-oxide (MO) solar thermochemical cycles, high temperature solar thermal energy is first converted to chemical energy in the form of a reduced MO. The reduced MO is then reoxidized in a second step with steam (or carbon dioxide) to produce hydrogen (or carbon monoxide) at a lower temperature. Solar thermochemical cycles of this type circumvent heat-to-electrical conversion required for electrochemical water splitting and promise high efficiencies. However, significant challenges remain to implementation. Ultra-high temperatures and efficiency-sapping low per-cycle conversion stand out as particularly difficult hurdles. Hybrid approaches utilizing both thermal and electrical energy provide some of the advantages of each, and can facilitate lower temperature operation and offer better per-pass utilization than thermochemical alone. However, early concepts for implementing the thermo-electrochemical approach introduced substantial new challenges including difficult separations, corrosive environments, and energy losses from large temperature swings and phase changes. We are currently investigating two different options for implementation. In the first, a MO that reduces at lower temperature is selected. As the reduced MO lacks the full thermodynamic driving force to effectively split water, the reaction is driven forward by an electrically-assisted proton-conducting membrane that separates and recovers hydrogen as it is produced. This approach produces a pure hydrogen stream, is mechanically simple, and has unique thermodynamic advantages. The second option seeks to more directly couple the electrical boost to the solid MO to drive either the reduction or oxidation step, or both, through the utilization of layered MO materials and advanced reactors. This approach could be applied to both water and carbon dioxide splitting. The results of process modeling and optimization will be presented, and progress towards demonstrating the concepts at the laboratory scale will be discussed.

08 HYDROGEN↗

Solar Ammonia Production via Novel Two-step Thermochemical Looping of a Co 3 Mo 3 N/Co 6 Mo 6 N pair [Slides]

Ternary nitrides in the family A 3 B x N (A=Co, Ni, Fe; B=Mo; x=2,3) identified and synthesized. Experiments with Co 3 Mo 3 N in Ammonia Synthesis Reactor demonstrate cyclable NH3 production from bulk nitride under pure H 2 . Production rates were approx. constant in all the reduction steps with no evident dependence on the consumed solid-state nitrogen up to formation of 661. Material can be re-nitridized under pure N 2 (or 10% H 2 /N 2 ). Bulk N utilization per reduction step averaged between 25 – 40% of the total (2-3 hours). Rate equations and parameters extracted from data. NH 3 selectivity exceeds gas phase equilibrium at higher temperatures (in a large excess of H 2 ). Selectivity begins to decrease significantly above 650 C, N 2 production rapidly increases above 650 C seemingly due to reaction that is zero order in H 2 (thermal reduction of the nitride?). Poised to begin the systematics studies of relationships between materials and reactions.

14 SOLAR ENERGY↗

Solar-Thermal Ammonia Production Via a Nitride Looping Cycle [Slides]

Solar Thermal Ammonia Production has the potential to synthesize ammonia in a green, renewable process that can greatly reduce the carbon footprint left by conventional Haber-Bosch reaction. Ternary nitrides in the family A 3 B x N (A=Co, Ni, Fe; B=Mo; x=2,3) have been identified as a potential candidate for NH 3 production. Experiments with Co 3 Mo 3 N in Ammonia Synthesis Reactor demonstrate cyclable NH 3 production from bulk nitride under pure H 2 . Production rates were fairly flat in all the reduction steps with no evident dependence on the consumed solid-state nitrogen, as would be expected from catalytic Mars-van Krevelen mechanism. Material can be re-nitridized under pure N 2 . Bulk nitrogen per reduction step average between 25 – 40% of the total solid-state nitrogen. Selectivity to NH 3 stabilized at 55 – 60% per cycle. Production rates (NH 3 and N 2 ) become apparent above 600 °C at P(H 2 ) = 0.5 – 2 bar. Optimal point of operation to keep selectivity high without compromising NH 3 rates currently estimated at 650 °C and 1.5 - 2 bar. The next steps are to optimize production rates, examine effect of N 2 addition in NH 3 synthesis reaction, and test additional ternary nitrides.

14 SOLAR ENERGY↗

Redox-active oxide materials for thermal energy storage

Thermochemical storage materials having the general formula AxA′1-xByB′1-yO3-δ, where A=La, Sr, K, Ca, Ba, Y and B=Mn, Fe, Co, Ti, Ni, Cu, Zr, Al, Y, Cr, V, Nb, Mo, are disclosed. These materials have improved thermal storage energy density and reaction kinetics compared to previous materials. Concentrating solar power thermochemical systems and methods capable of storing heat energy by using these thermochemical storage materials are also disclosed.

Babiniec, Sean M.↗

Modified Calcium Manganites for Thermochemical Energy Storage Applications

CaAl 0.2 Mn 0.8 O 3-δ (CAM28) and CaTi 0.2 Mn 0.8 O 3-δ (CTM28) are perovskite metal oxides developed for high-temperature thermochemical energy storage (TCES) applications, e.g., in support of air Brayton power generation. Previous reports for these compounds focus on the equilibrium non-stoichiometry (δ) as a function of temperature and oxygen partial pressure (pO 2 ) and the endotherm (or exotherm) accompanying changes in δ resulting from thermal reduction (or re-oxidation). Herein, we report results for elemental substitution and doping (Al, Co, Fe, La, Sr, Ti, Y, Zn, and Zr) of calcium manganites (CM) that establish the preference for CAM28 and CTM28. Techniques employed include conventional (screening and equilibrium) and ballistically heated multi-cycle thermogravimetric analysis (TGA), conventional and high temperature ( in-situ ) X-ray diffraction (XRD), and differential scanning calorimetry (DSC). Forward-looking results for A-site Y-doped materials, e.g., Ca 0.9 Y 0.1 MnO 3-δ (CYM910), establish a route to increasing the reduction enthalpy relative to CAM28 and CTM28, albeit at the expense of increased reduction temperatures and raw materials costs. A thermodynamic model presented for CAM28, but extendable to related materials, provides values for the reaction enthalpy and extent of reduction as a function of temperature and oxygen partial pressure for use in design efforts. Taken as a whole, the results support the choice of Al-doped CaMnO 3-δ as a low-cost material for TCES in a high temperature air Brayton application, but point the way to achieving higher stored energy densities that could lead to overall cost savings.

Miller, James E.↗

Techno-Economic Analysis of a Concentrating Solar Power Plant Using Redox-Active Metal Oxides as Heat Transfer Fluid and Storage Media

We present results for a one-dimensional quasi-steady-state thermodynamic model developed for a 111.7 MW e concentrating solar power (CSP) system using a redox-active metal oxide as the heat storage media and heat transfer agent integrated with a combined cycle air Brayton power block. In the energy charging and discharging processes, the metal oxide CaAl 0.2 Mn 0.8 O 2.9-δ (CAM28) undergoes a reversible, high temperature redox cycle including an endothermic oxygen-releasing reaction and exothermic oxygen-incorporation reaction. Concentrated solar radiation heats the redox-active oxide particles under partial vacuum to drive the reduction extent deeper for increased energy density at a fixed temperature, thereby increasing storage capacity while limiting the required on sun temperature. Direct counter-current contact of the reduced particles with compressed air from the Brayton compressor releases stored chemical and sensible energy, heating the air to 1,200°C at the turbine inlet while cooling and reoxidizing the particles. The cool oxidized particles recirculate through the solar receiver subsystem for another cycle of heating and reduction (oxygen release). We applied the techno-economic model to 1) size components, 2) examine intraday operation with varying solar insolation, 3) estimate annual performance characteristics over a simulated year, 4) estimate the levelized cost of electricity (LCOE), and 5) perform sensitivity analyses to evaluate factors that affect performance and cost. Simulations use hourly solar radiation data from Barstow, California to assess the performance of a 111.7 MW e system with solar multiples (SMs) varying from 1.2 to 2.4 and storage capacities of 6–14 h. The baseline system with 6 h storage and SM of 1.8 has a capacity factor of 54.2%, an increase from 32.3% capacity factor with no storage, and an average annual energy efficiency of 20.6%. Calculations show a system with an output of 710 GWh e net electricity per year, 12 h storage, and SM of 2.4 to have an installed cost of $329 million, and an LCOE of 5.98 ¢/kWh e . This value meets the U.S. Department of Energy’s SunShot 2020 target of 6.0 ¢/kWh e ( U. S Department of Energy, 2012 ), but falls just shy of the 5.0 ¢/kWh e 2030 CSP target for dispatchable electricity ( U. S Department of Energy, 2017 ). The cost and performance results are minimally sensitive to most design parameters. However, a one-point change in the weighted annual cost of capital from 8 to 7% (better understood as a 12.5% change) translates directly to an 11% decrease (0.66 ¢/kWhe) in the LCOE.

Gorman, Brandon T.↗

Metal nitride materials for solar-thermal ammonia production [Slides]

Solar Thermal Ammonia Production has the potential to synthesize ammonia in a green, renewable process that can greatly reduce the carbon footprint left by the conventional Haber-Bosch reaction. Co 3 Mo 3 N has been identified as a potential candidate for ammonia production. It is synthesized via oxide precursor synthesis followed by nitridation under 10% H 2 /N 2 . The synthesis method can be extended to other candidate nitrides. The Co 3 Mo 3 N → Co 6 Mo 6 N reduction is demonstrated on TGA with rapid kinetics. The formation of NH 3 is qualitatively observed, but not quantitatively determined. The material retains crystal structure, but no secondary phases are observed in XRD. Partial re-nitridation back to CMN331 of ~35% of max nitridation is observed. Reaction parameters in TGA differ from experimental conditions in the literature. Experiments at Georgia Tech better mimic re-nitridation conditions with more sensitive, quantitative analytical techniques (GC-MS). The ASU NH 3 synthesis/re-nitridation reactor is under development and will permit experiments (reduction/re-nitridation) under precisely controlled T, pH 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Proppant compositions and methods of use

Proppant compositions for use in hydraulic fracturing and methods of using same are disclosed herein. The proppant compositions include a plurality of proppant particulates and at least one particulate of the plurality of proppant particulates containing at least one tracer, wherein the at least one tracer separates from the at least one particulate located inside a fracture of a subterranean formation after a period of time.

Cannan, Chad↗

Redox-active oxide materials for thermal energy storage

Thermochemical storage materials having the general formula A x A′ 1-x B y B′ 1-y O 3-δ , where A=La, Sr, K, Ca, Ba, Y and B=Mn, Fe, Co, Ti, Ni, Cu, Zr, Al, Y, Cr, V, Nb, Mo, are disclosed. These materials have improved thermal storage energy density and reaction kinetics compared to previous materials. Concentrating solar power thermochemical systems and methods capable of storing heat energy by using these thermochemical storage materials are also disclosed.

14 SOLAR ENERGY↗

Redox-active oxide materials for thermal energy storage

Thermochemical storage materials having the general formula AxA′1-xByB′1-yO3-δ, where A=La, Sr, K, Ca, Ba, Y and B=Mn, Fe, Co, Ti, Ni, Cu, Zr, Al, Y, Cr, V, Nb, Mo, are disclosed. These materials have improved thermal storage energy density and reaction kinetics compared to previous materials. Concentrating solar power thermochemical systems and methods capable of storing heat energy by using these thermochemical storage materials are also disclosed.

14 SOLAR ENERGY↗

Methods for operating solar-thermochemical processes

Methods for controlling or operating solar thermochemical reactions process that maximize the two-step thermochemical energy cycle efficiency by a combination of pressure and temperature swing are disclosed.

14 SOLAR ENERGY↗

Methods utilizing durable functional materials for chemical processes that include an oxidation step

The present disclosure is directed to methods using durable functional materials for processes that include an oxidation step. The durable functional materials are redox active oxygen carrier materials that include a zirconia or yttria-stabilized-zirconia (YSZ) matrix containing a redox-active metal ion(s), such as, but not limited to Fe, Mn, Cu, Co and Cr. In an embodiment, these materials are used in chemical looping processes.

36 MATERIALS SCIENCE↗