Engineering topics

Miller, C. G.

Publications and source records attributed to Miller, C. G..

At least 37 records · Page 2

NASA NTRS1982

An experimental investigation of hypersonic flow over biconics at incidence and comparison to prediction

Pressure distributions, aerodynamic coefficients, shock shapes, and oil-flow patterns were measured on spherically blunted, 12.84 deg/7 deg on-axis and bent biconics at Mach 6 in air. The angle of attack, referenced to the axis of the aft-cone, was varied from -10 to 40 deg in nominal 5 deg increments. Predictions from an inviscid flowfield computer code referred to as STEIN and codes which solve the three-dimensional parabolized Navier Stokes (PNS) equations were compared with measurement. Three PNS codes were found which provided accurate predictions of windward and leeward pressure distributions for angles of attack to 25 deg.

Miller, C. G.↗

NASA NTRS1982

Experimental investigation of gamma effects on heat transfer to a 0.006 scale Shuttle Orbiter at Mach 6

Real-gas effects on heating to the windward centerline of the Shuttle Orbiter and shock shape were simulated by testing a 0.006-scale Orbiter model in Mach 6 air and CF4 flows. The range of free-stream Reynolds number, based on model length, was 0.4 x 10 to the 6th to 5.3 x 10 to the 6th for air, resulting in laminar and turbulent heating. The Reynolds number for CF4 was 0.3 x 10 to the 6th and gamma was equal to 1.13, corresponding to a normal shock density ratio of 12 as compared to 5.25 in air. Angle of attack was varied from 15 deg to 45 deg in 5 deg increments. Centerline heating distributions were compared for the two gases, and to Mach 8 wind-tunnel data, predictions, and flight (STS-1 and STS-2) data. The present results revealed a significant increase in heating with increasing density ratio and decreasing Reynolds number at the lower angles of attack; the effects of density ratio and Reynolds number diminished with increasing angle of attack and were relatively small at the angles of attack for the hypersonic portion of Space Shuttle Orbiter flights STS-1 and STS-2. Wind-tunnel and flight heating distributions were in relatively good agreement, and the present heating rates in air were accurately predicted by a local infinite swept cylinder analysis.

Miller, C. G.↗

NASA NTRS1981

Semitransparent curtains for control of optical radiation hazards

The purposes and functions of semitransparent eye protective curtains are analyzed. Based upon this analysis, functional requirements are developed, and design requirements are specified for optimum curtains to be used with open arc welding and arc cutting processes. Such curtains also protect against other high intensity broad-spectral-band sources such as compact arc lamps. The requirements for filtering out hazardous UV radiation and blue light must be balanced against the need for transparency in the visible spectrum and the need for reduced glare. Infrared attenuation is shown to be of very little importance.

Sliney, D. H.↗

NASA NTRS1981

Gas absorption/desorption temperature-differential engine

Continuously operating compressor system converts 90 percent of gas-turbine plant energy to electricity. Conventional plants work in batch mode, operating at 40 percent efficiency. Compressor uses metal hydride matrix on outside of rotating drum to generate working gas, hydrogen. Rolling valve seals allow continuous work. During operation, gas is absorbed, releasing heat, and desorbed with heat gain. System conserves nuclear and fossil fuels, reducing powerplant capital and operating costs.

Miller, C. G.↗

NASA NTRS1980

Underground mineral extraction

A method was developed for extracting underground minerals such as coal, which avoids the need for sending personnel underground and which enables the mining of steeply pitched seams of the mineral. The method includes the use of a narrow vehicle which moves underground along the mineral seam and which is connected by pipes or hoses to water pumps at the surface of the Earth. The vehicle hydraulically drills pilot holes during its entrances into the seam, and then directs sideward jets at the seam during its withdrawal from each pilot hole to comminute the mineral surrounding the pilot hole and combine it with water into a slurry, so that the slurried mineral can flow to a location where a pump raises the slurry to the surface.

Miller, C. G.↗

NASA NTRS1980

Liquid/liquid heat exchanger

Conceptual design for heat exchanger, utilizing two immiscible liquids with dissimilar specific gravities in direct contact, is more efficient mechanism of heat transfer than conventional heat exchangers with walls or membranes. Concept could be adapted for collection of heat from solar or geothermal sources.

Miller, C. G.↗

NASA NTRS1980

Improved optics for an ultracentrifuge

Ultracentrifuge is important tool in study of polymers, biomolecules, and cell structures. In typical ultracentrifuge rotor supports pair of optically matched vials; one contains sample mixed in solvent, and other is reference that contains only solvent. Doubleslit optical system, transverse to rotor, creates interference pattern on photographic plate each time vials pass through optics. Medium in sample vial displaces interference maximums such that shift gives measurement of density distribution along length of sample.

Miller, C. G.↗

NASA NTRS1980

Sealed-in-quartz resistance heater

Electric resistance quartz heater operates at 1,400 F without developing excessively hot spots that can fail prematurely. Since resistance element is sealed in quartz, heater can be used in hostile environments. Sealed construction also keeps heater from contaminating heated object.

Miller, C. G.↗

NASA NTRS1979

Variable-shape solar-energy concentrator

Proposed low cost three dimensional tracking solar concentrator fabricated from lightweight, flexible polymeric film membrane is controlled in shape by differential pressure loading. Fine adjustments to shape could be made by mounting electrets or magnets on membrane or applying electric or magnetic field.

Miller, C. G.↗

NASA NTRS1979

Primary reflector for solar energy collection systems and method of making same

Solar energy is reflected to a movably supported collector that is kept at the concentrated line focus of the reflector primary by a fixed, linear, ground-based primary reflector having an extended curved sawtooth contoured surface covered with a metalized polymeric reflecting material. The primary reflector was constructed by a process utilizing well-known freeway paving machinery.

Miller, C. G.↗

NASA NTRS1979

Solar energy collection system

A fixed, linear, ground-based primary reflector having an extended curved sawtooth-contoured surface covered with a metalized polymeric reflecting material, reflects solar energy to a movably supported collector that is kept at the concentrated line focus reflector primary. The primary reflector may be constructed by a process utilizing well known freeway paving machinery. The solar energy absorber is preferably a fluid transporting pipe. Efficient utilization leading to high temperatures from the reflected solar energy is obtained by cylindrical shaped secondary reflectors that direct off-angle energy to the absorber pipe. A seriatim arrangement of cylindrical secondary reflector stages and spot-forming reflector stages produces a high temperature solar energy collection system of greater efficiency.

Miller, C. G.↗

NASA NTRS1979

Coal mining with a liquid solvent

Study suggests carbonated water can dissolve or suspend coal and carry it to surface. Mixture of carbon dioxide and water may be coal solvent that will make unmanned mining reality. When used with proposed process monitoring coal solubility with conventional strain gage, solvent is basis for rapid cost effective extraction of coal from underground seams.

Lawson, D. D.↗

NASA NTRS1978

Primary reflector for solar energy collection systems

A fixed, linear, ground-based primary reflector is disclosed which has an extended curved sawtooth-contoured surface covered with a metalized polymeric reflecting material. The device reflects solar energy to a movably supported collector that is kept at the concentrated line focus of the reflector primary. The primary reflector may be constructed by a process utilizing well-known freeway paving machinery.

Miller, C. G.↗

NASA NTRS1978

Description and preliminary calibration results for the Langley hypersonic CF4 tunnel

A detailed description of the hypersonic CF4 tunnel is presented along with discussion of the basic components, instrumentation, and operating procedure. Operational experience with the CF4 reclaimer and lead-bath heater is discussed. Comparison of measured and predicted shock detachment distance on a sphere and pressure distributions measured on a sharp leading-edge flat plate revealed the absence of significant flow nonuniformity and lent creditability to predicted free stream flow conditions. The economic operation of this facility centers about the CF4 reclaimer, which was designed to operate at an efficiency of 90 to 95 percent. A number of modifications were made to the reclaimer system to improve its performance, and presently, the system reclaims approximately 75 percent of the test gas. Even with current budgetary constraints, this efficiency permits the CF4 tunnel to be operated as a viable research wind tunnel.

Midden, R. E.↗

NASA NTRS1978

Solar pond

Shallow pools of liquid to collect low-temperature solar generated thermal energy are described. Narrow elongated trenches, grouped together over a wide area, are lined with a heat-absorbing black liner. The heat-absorbing liquid is kept separate from the thermal energy removing fluid by means such as clear polyethylene material. The covering for the pond may be a fluid or solid. If the covering is a fluid, fire fighting foam, continuously generated, or siloons are used to keep the surface covering clean and insulated. If the thermal energy removing fluid is a gas, a fluid insulation layer contained in a flat polyethlene tubing is used to cover the pond. The side of the tube directed towards the sun is treated to block out ultraviolet radiation and trap in infrared radiation.

Miller, C. G.↗

NASA NTRS1978

A critical examination of expansion tunnel performance

An experimental study of the performance of the expansion tunnel for various test gases and range of quiescent acceleration section and nozzle pressure, nozzle geometric area ratio, and nozzle axial station has been performed. Flow diagnostics used to examine expansion tunnel flow characteristics were time histories and profiles of pitot pressure and axial component of flow velocity. The purpose of this study was to determine experimentally what limitations might restrict predicted operational flexibility and the advantages and disadvantages of this mode of operation as compared to the expansion tube. Results are presented which demonstrate the expansion tunnel offers several advantages over the expansion tube, but the severity of the disadvantages of the tunnel makes the expansion tube mode of operation the more desirable for performing hypersonic-hypervelocity aerothermodynamic studies of proposed entry configurations.

Miller, C. G.↗

NASA NTRS1977

Low cost solar energy collection system

A fixed, linear, ground-based primary reflector having an extended, curved sawtooth contoured surface covered with a metallized polymeric reflecting material, reflected solar energy to a movably supported collector that was kept at the concentrated line focus of the reflector primary. Efficient utilization leading to high temperatures from the reflected solar energy was obtained by cylindrical shaped secondary reflectors that directed off-angle energy to the absorber pipe.

Miller, C. G.↗

NASA NTRS1977

Operational experience in the Langley expansion tube with various test gases

The Langley Expansion Tube is an operational facility capable of producing good quality, highly repeatable, quasi-steady flow for test times sufficient to establish flow about blunt axisymmetric and two-dimensional models. Due to the capability of testing with arbitrary test gases, a wide range of real-gas, hypersonic-hypervelocity flow conditions may be generated. However, for a given test gas, the range of operating conditions producing useful flow is shown to be rather limited; hence, the facility yields a given flow condition for a given test gas, and variation in flow conditions comes about by using different test gases. Data are presented for operations using air and carbon dioxide as test gases. The driver gas was unheated helium at a nominal pressure of 5000 psi (34.5 MN sq m).

Miller, C. G.↗