Engineering topics

Miller, B. A.

Publications and source records attributed to Miller, B. A..

28 records · Page 2

NASA NTRS1974

Low-speed wind-tunnel investigation of the aerodynamic and acoustic performance of a translating grid choked flow inlet

The aerodynamic and acoustic performance of a translating grid choked-flow inlet was determined in a low-speed wind tunnel at free-stream velocities of 24, 32, and 45 m/sec and incidence angles of 0, 10, 20, 30, 35, 40, 45, and 50 deg. The inlet was sized to fit a 13.97- centimeter-diameter fan with a design weight flow of 2.49 kg/sec. Measurements were made to determine inlet total pressure recovery, flow distortion, and sound pressure level for both choked and unchoked geometries over a range of inlet weight flows. For the unchoked geometry, inlet total pressure recovery ranged from 0.983 to 0.989 at incidence angles less than 40 deg. At 40 deg incidence angle, inlet cowl separation was encountered which resulted in lower values of pressure recovery and higher levels of fan broadband noise. For the choked geometry, increasing total pressure losses occurred with increasing inlet weight flow that prevented the inlet from reaching full choked conditions with the particular fan used. These losses were attributed to the high Mach number drag rise characteristics of airfoil grid. At maximum attainable inlet weight flow, the total pressure recovery at static conditions was 0.935. The fan blade passing frequency and other fan generated pure tones were eliminated from the noise spectrum, but the broadband level was increased.

Abbott, J. M.↗

NASA NTRS1973

Effect of Subsonic Inlet Lip Geometry on Predicted Surface and Flow Mach Number Distributions

The effect of subsonic inlet lip geometry on predicted surface and flow Mach number distributions is illustrated. The theoretical results were obtained from incompressible potential flow calculations corrected for compressibility. The major emphasis of this investigation is on the low-speed (takeoff and landing) operating conditions. The low-speed results were obtained for a range of three geometric variables of interest: contraction ratio, defined as the ratio of highlight area to throat area; internal lip major - to minor-axis ratio; and internal lip shape. The low-speed results were obtained at both static conditions and a free-stream velocity of 42.6m/sec, with incidence angles ranging from 0 deg to 50 deg. The results indicate that of the three geometric variables considered, contraction ratio had the largest effect on the surface Mach number distributions. The effects of inlet diameter ratio and blunting of the external forebody on maximum external surface Mach numbers are illustrated at a cruise Mach number of 0.8.

Albers, J. A.↗

NASA NTRS1973

Low-speed wind tunnel investigation of the aerodynamic and acoustic performance of a translating-centerbody choked-flow inlet

Low-speed wind-tunnel tests were conducted to determine the effects of free-stream velocity and incidence angle on the aerodynamic and acoustic performance of a translating centerbody choked-flow inlet. The inlet was sized to fit a 13.97 cm diameter fan with a design weight flow of 2.49 kg/sec. Performance was determined at free-stream velocities to 45 meters per second and incidence angles of 0 deg to 50 deg. The inlet was operated in both the choked and unchoked modes over a range of weight flows. Measurements were made of inlet total pressure recovery, flow distortion, surface static pressure distribution, and fan noise suppression. In the choked mode, increasing incidence angle tended to reduce the amount of inlet noise suppression for a given amount of inlet suction. This tendency was overcome by applying sufficient inlet suction to increase the flow Mach number. At 45 meters per second free-stream velocity, at least 22 decibels of suppression were measured at 35 deg incidence angle with a total pressure recovery of 0.985.

Miller, B. A.↗

NASA NTRS1972

Aerodynamic and Acoustic Performance of Two Choked-Flow Inlets Under Static Conditions

Tests were conducted to determine the aerodynamic and acoustic performance of two choking flow inlets under static conditions. One inlet choked the flow in the cowl throat by an axial translation of the inlet centerbody. The other inlet employed a translating grid of airfoils to choke the flow. Both inlets were sized to fit a 13.97 cm diameter fan with a design weight flow of 2.49 kg/sec. The inlets were operated in both the choked and unchoked modes over a range of weight flows. Measurements were made of inlet pressure recovery, flow distortion, surface static pressure distribution, and fan noise suppression. Choking of the translating centerbody inlet reduced blade passing frequency noise by 29 db while yielding a total pressure recovery of 0.985. Noise reductions were also measured at 1/3-octave band center frequencies of 2500, 5000, and 20,000 cycles. The translating grid inlet gave a total pressure recovery of 0.968 when operating close to the choking weight flow. However, an intermittent high intensity noise source was encountered with this inlet that precluded an accurate measurement of inlet noise suppression.

Miller, B. A.↗

NASA NTRS1972

Engine noise technology

The characteristics of aircraft engine noise are discussed. Data are provided to show the noise produced by the following aircraft components: (1) fan noise, (2) noise suppressing structures, (3) sonic inlets, (4) jet mixing noise due to nozzle flow, and (5) thrust reversers. Charts are developed to show the sound pressure level and the frequencies for each type of noise source. The use of laminates and composite materials to dissipate acoustic power is examined.

Luidens, R. W.↗

NASA NTRS1968