Engineering topics

Meyer, Harry M.

Publications and source records attributed to Meyer, Harry M..

17 records

DOE OSTI2024

The Impact of Lithium Anode Interface on Capacity Fade in Polymer Electrolyte-Based Solid-State Batteries

This study investigates the Li stripping-plating morphology and failure mechanisms in full cells consisting of a solid polymer electrolyte (SPE) with two commercial Li anodes: Li chip and Li foil. The primary identified failure mechanism of the SPE cell is capacity fade, regardless of the Li manufacturer. While the cathode’s role in capacity fade is evident, the Li anode significantly influences cycling performance, with Li foil cells cycling 50% longer than Li chip cells, a statistical difference. Further, post-mortem scanning electron microscopy and X-ray photoelectron spectroscopy results attribute the Li chip’s faster capacity fade to a loss of contact and continuous growth of the solid electrolyte interphase (SEI). Conversely, Li foil maintains consistent contact with the solid polymer, displaying a thin and stable SEI. Additionally, failure mechanisms between a gel electrolyte in previous work and the dry SPE are compared.

25 ENERGY STORAGE↗

DOE OSTI2024

Mitigating municipal solid waste fouling in biofuel conversion via screw surface modifications

Here, municipal solid waste (MSW)'s 40–60 % carbon content makes it a feedstock for biofuel production via pyrolysis. One challenge in the conversion process is MSW fouling due to thermal decomposition. The accumulated deposit on the injection screw often leads to plugging and constriction. This study examined the morphology and composition of the MSW fouling deposit and conducted a thermal simulation to understand the temperature gradience of the injection screw. Surface modifications including smoothening and anti-adhesion coating were proposed for the injection screw to address the deposit problem. For evaluating the candidate mitigations, a bench-scale fouling test was developed with the gas environment, temperature, and sliding speed relevant to the contact interface between the MSW particles and the screw. Results suggested that a smoother screw surface could reduce the grip and a non-metallic coating with a lower surface energy could decrease adhesion, consequently leading to less fouling. Specifically, reducing the roughness from 2 to 0.6 and then to 0.2 μm proportionally decreased the amount of deposit, and the diamond-like-carbon, CrN, and NiCr–CrC composite coatings effectively hindered the fouling process. This study provides fundamental insights into the MSW fouling and proof-of-concept of potential mitigations through the screw surface modification.

09 BIOMASS FUELS↗

DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Elucidating the Role of Carbon Conductive Additive in the Processing and Electrochemical Behavior of Surface-Modified Si Anodes

In the present work, we explore the impact of conducting carbon on the processing of silicon (Si)-rich electrodes, their resulting cycling performance, and parasitic side reactions. We employed three different carbon additives, Super C45 (carbon black), Super C65 (carbon black), and TIMCAL C-NERGY KS 6L (graphite), with varying sizes and morphologies to determine how these parameters influence the structure and the electrochemical behavior of the cast electrodes. Raman mapping indicates that the improved performance achieved using C45 can be explained by the homogeneous distribution of Si and carbon, enabling the formation of continuous electrical pathways throughout the electrode. Further, this finding aligns with the results of ζ potential measurements, which indicate that C45 can maintain more stable dispersions in N-methyl-2-pyrrolidone (NMP) compared with the other carbon additives. However, electrodes with C45 as the conducting agent exhibited increased parasitic side reactions, as evidenced by the leakage current obtained from voltage hold experiments. These side reactions can have adverse effects on the calendar life of the electrode. Furthermore, the Raman maps of the electrodes reveal heterogeneities in Si and carbon distribution with lower carbon content, especially with only 2% carbon. This drastically impacts the cyclability of the electrodes, with portions of the low-carbon electrodes that remain unable to undergo cycling even at slow rates (0.2 Ah g –1 ). Additionally, we found that slower formation rates are favored in the context of parasitic side reactions, although slower formation rates can potentially create thicker passivating films that could hinder Li + -ion transport. Therefore, we emphasize the need for an intricate balance in materials selection and cycling protocol for optimal electrode processing and electrochemical behavior.

25 ENERGY STORAGE↗

DOE OSTI2024

Minimizing Toxicity and Optimizing Lubricity of Ionic Liquids for Eco-Friendly Lubrication

As much as 60 million liters of lubricating fluids end up in the environment annually, and thus, the environmental impact of lubricants is increasingly recognized in addition to meeting the rheological and tribological requirements. Although US Environmental Protection Agency-approved environmentally acceptable base fluids are available, there is a lack of additives that are both nontoxic and effective in wear protection. Here, this study reports the successful development of a new class of ionic liquids (ILs) with demonstrated significantly lower aquatic toxicity and superior friction reduction and wear protection capabilities compared with a commercial lubricant additive and some ILs reported in the literature. Specifically, ammonium phosphate and phosphonium phosphate ILs with four-carbon alkyls have been identified with balanced oil solubility, thermal stability, toxicity, and lubricity, which provide fundamental insights for future development of eco-friendly ILs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Low-Temperature Molten Salt Electrochemical CO 2 Upcycling for Advanced Energy Materials

One strategy for addressing the climate crisis caused by CO 2 emissions is to efficiently convert CO 2 to advanced materials suited for green and clean energy technology applications. Porous carbon is widely used as an advanced energy storage material because of its enhanced energy storage capabilities as an anode. Herein, we report electrochemical CO 2 upcycling to solid carbon with a controlled microstructure and porosity in a ternary molten carbonate melt at 450 °C. Controlling the electrochemical parameters (voltage, temperature, cathode material) enabled the conversion of CO 2 to porous carbon with a tunable morphology and porosity for the first time at such a low temperature. Additionally, a well-controlled morphology and porosity are beneficial for reversible energy storage. In fact, these carbon materials delivered high specific capacity, stable cycling performances, and exceptional rate capability even under extremely fast charging conditions when integrated as an anode in lithium-ion batteries (LIBs). In conclusion, the present approach not only demonstrated efficient upcycling of CO 2 into porous carbon suitable for enhanced energy storage but can also contribute to a clean and green energy technology that can reduce carbon emissions to achieve sustainable energy goals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Carbon Coating Influence on the Formation of Percolating Electrode Networks for Silicon Anodes

Previous studies have demonstrated that chemical vapor deposition carbon coating on silicon (Si@C) can enhance the electrochemical performance of lithium-ion batteries with Si-based anodes. However, the underlying mechanisms contributing to this improvement have not been fully explored. Here, we address this knowledge gap by applying a suite of characterization methods to evaluate Si@C anodes prepared by reducing acetylene on ball-milled Si particles. Raman mapping measurements show that the C coating (<5 nm thick) enables a homogeneous Si and carbon distribution during the slurry casting process, thereby promoting Si utilization during cycling. The coating’s microstructure and morphology were evaluated using X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy, and neutron reflectivity experiments. Electrochemical impedance spectroscopy measurements upon cycling indicate that carbon coating also reduces the overall resistance as benchmarked against bare Si anodes. Galvanostatic cycling in half-cell studies revealed higher initial Coulombic efficiency and specific capacities with increasing carbon coating time. However, solid electrolyte interphase (SEI) investigations using XPS showed that the coated and uncoated samples have very similar characteristics, suggesting that the SEI may only play a minor role in enhancing the performance of Si@C. Full-cell evaluation of the Si electrodes was consistent with half-cell results relating to performance and SEI properties, further supporting the conclusion that electronic and ionic percolation, enabled by effective electrode manufacturing, are the dominant factors contributing to the favorable performance of Si@C.

25 ENERGY STORAGE↗

DOE OSTI2023

Ionomer-free nanoporous iridium nanosheet electrodes with boosted performance and catalyst utilization for high-efficiency water electrolyzers

Increasing the catalyst utilization efficiency and simplifying electrode fabrication processes are crucial to accelerate development of low-cost proton exchange membrane electrolyzer cells (PEMECs). Here, we develop a facile route to fabricate ionomer-free iridium nanosheet integrated electrodes, in which nanoporous iridium nanosheets (IrNS) with abundant exposed edges and nanopores are deposited on thin titanium liquid/gas diffusion layers (TT-LGDLs) via a low-temperature chemical synthesis strategy. Further, benefiting from high catalytic activity, good electrode conductivity and excellent liquid/gas transport properties, such nanoporous IrNS electrodes with low catalyst loadings require low cell voltages of 1.65 V and 1.78 V at 3000 and 6000 mA/cm 2 , respectively. More impressively, a stable performance can be well maintained under extremely high current density tests of 5000 mA/cm 2 , demonstrating the potential of low-loading nanoporous IrNS electrodes in solid-electrolyte based electrochemical conversion cells that require high current density operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

In Situ Ion‐Exchange Metathesis Induced Conformal LiF Surface Films on Cathode (NMC811) as a Cathode Electrolyte Interphase

High-capacity cathodes (LiNi 0.8 Mn 0.1 Co 0.1 O 2 , NMC811) are promising for vehicle electrification because of their high gravimetric energy density. However, their electrochemical performance still relies upon the stability of the cathode electrolyte interphase (CEI). A highly reactive cathode interface leads to parasitic side reactions with electrolytes, resulting in accelerated capacity fading. Well-developed LiF and LiF-like inorganic compounds are believed to be good CEI components for stabilizing such reactive electrode interfaces. However, it is challenging to form an optimal surface sub-nanolayer of LiF on the cathode surfaces because of the complexity of the electrochemical reaction during battery cycling. Herein, the formation of a conformal LiF layer on the NMC811 electrode surface via an in situ ion-exchange metathesis process is reported, demonstrating a promising electrochemical performance because of a LiF-stabilized CEI. In situ generated LiF-coated NMC811 electrodes exhibit ≈97% capacity retention up to 100 cycles at a 0.3 C rate with average coulombic efficiency of ≈99.9% and ≈80% capacity retention up to 200 cycles at a 1 C rate with average coulombic efficiency of >99.6%. This finding may pave the way for reengineering the CEI to enhance the electrochemical performances and cycling stability of the high-capacity cathodes.

25 ENERGY STORAGE↗

DOE OSTI2022

Coal polymer composites prepared by fused deposition modeling (FDM) 3D printing

Coal is a vital energy resource worldwide, but pollutants and greenhouse gases from its combustion cause environmental problems. To explore the non-combustion approach to use and valorize coal, anthracite and lignite were blended with polyamide 12 (PA 12) through FDM printing in this work and compared in the composites. By adding lignite, Young’s modulus improved with increasing loading to 50 wt% while tensile strength leveled off among the composites, compared to that of PA 12. By contrast, the addition of anthracite decreased the tensile performance at all loadings. Rheology tests and morphology analyses suggested that the interactions between fillers (anthracite and lignite) and PA 12 may cause differences in tensile properties. In addition, the printed lignite composites showed improved thermal conductivity (~ twofold), indicating lignite demonstrates the potential to build functional composites. This work provides a strategy to use lignite in composites by 3D printing for value-added products and reduces the demand for petroleum-based polymers. Overall, our approach diverts lignite from combustion processes and alleviates the negative impact of lignite use on the environment.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Enhancing Cycling Stability and Capacity Retention of NMC811 Cathodes by Reengineering Interfaces via Electrochemical Fluorination

High-capacity cathodes (LiNi 0.8 Mn 0.1 Co 0.1 O 2 ) that can boost the energy density of lithium-ion batteries are promising candidates for vehicle electrification. However, several factors specific to high energy density materials entailing electrode reactions inhibit their application. Fluorination has shown a promising ability to combat the detrimental electrochemical performances of cathode materials, however, it remains difficult to achieve the desired functionality. In this work, a novel electrochemical fluorination (ECF) that demonstrates a promising electrochemical performance enhancement via stabilization of the cathode–electrolyte-interphase (CEI) by forming conformal LiF is proposed. Besides LiF surface layer formation, ECF reduces the degree of fluorination-induced Ni/Li disordering and enhances the layered structural stability as probed by X-ray diffraction. Because of the robust CEI, ECF-NMC811 cathodes deliver 203.0 mAh g -1 first discharge capacity at the current rate of C/10, with ≈98% capacity retention up to 100 cycles. Similarly, it delivers ≈180 mAh g -1 capacity at a 1 C rate with 86.4% capacity retention up to 200 cycles with average coulombic efficiency of > 99.5%. Comprehensive characterization with a multitude of probes reveals that ECF enhances the cycling stability of the electrode without altering bulk structure and morphology.

25 ENERGY STORAGE↗

DOE OSTI2021

Deactivation by Potassium Accumulation on a Pt/TiO 2 Bifunctional Catalyst for Biomass Catalytic Fast Pyrolysis

Biomass-derived feedstocks bring significant challenges to the longevity of the catalysts used for their conversion, and alkali metals, for example, K, in the feedstock have been widely ascribed as one of the important factors causing catalyst deactivation. To address this challenge, it is critical to understand the mechanism of catalyst deactivation caused by K accumulation to guide the improvement of catalysts and processes and the development of catalyst regeneration strategies. In this work, we report a deep understanding of the impact of K on a bifunctional Pt/TiO 2 catalyst, which is an efficient catalyst for the ex situ catalytic fast pyrolysis of biomass. We simulated the K-poisoning of Pt/TiO 2 catalysts by purposely loading different amounts of K (100-6000 ppm by weight) on the catalysts. A series of characterization approaches, including scanning transmission electron microscopy, Fourier transform infrared spectroscopy, and chemical titration, were combined with a kinetic assessment of multiple probe reactions to elucidate the mechanism of Pt/TiO 2 deactivation by K accumulation. At low K loadings (<800 ppm), K preferentially poisons the strong Lewis acid sites, leading to significantly reduced activity for acid-catalyzed alcohol dehydration. However, acetone condensation is less sensitive to the poisoning of strong Lewis acid sites. Reactions that occur on Pt sites or at the metal-support interface, including alkene hydrogenation, m-cresol hydrodeoxygenation (HDO), and CO oxidation, were not impacted. At high K loadings (>800 ppm), K starts to accumulate on the Pt-TiO 2 interfacial area, poisoning the interfacial active sites for HDO and CO oxidation reactions. We further found that the poisoning of the Pt/TiO 2 catalyst by K is reversible, and water washing can successfully remove the accumulated K and recover the activities for both alcohol dehydration and m-cresol HDO reactions.

09 BIOMASS FUELS↗

DOE OSTI2021

Formation of LiF Surface Layer During Direct Fluorination of High-Capacity Co-Free Disordered Rocksalt Cathodes

Disordered rocksalt (DRX) cathodes have attracted interest due to their high capacity and compositional flexibility (e.g., Co-free chemistries). However, the sloping voltage profile and gradual capacity fade during cycling have hindered widespread adoption of these materials. Simulations predict that fluorine substitution in DRX cathodes will improve their capacity, rate performance and cyclability. In this study we use a fluidized bed reactor to fluorinate a model Lirich DRX composition (Li1.15Ni0.375Ti0.375Mo0.1O2, NTMO) to investigate how fluorine content impacts the cathode’s structure and electrochemical performance. Instead of substituting O with F to form oxyfluoride phases, direct fluorination of DRX cathodes leads to formation of LiF surface films which improves the specific energy and capacity retention. This study demonstrates the feasibility of direct fluorination to improve the electrochemical performance of high voltage cathodes by tuning the material’s surface chemistry.

Co-free disordered rock-salt cathode, direct fluor↗

DOE OSTI2021

Photoinduced Strong Metal–Support Interaction for Enhanced Catalysis

Strong metal–support interaction (SMSI) construction is a pivotal strategy to afford thermally robust nanocatalysts in industrial catalysis, but thermally induced reactions (>300 °C) in specific gaseous atmospheres are generally required in traditional procedures. In this work, a photochemistry-driven methodology was demonstrated for SMSI construction under ambient conditions. Encapsulation of Pd nanoparticles with a TiO x overlayer, the presence of Ti 3+ species, and suppression of CO adsorption were achieved upon UV irradiation. The key lies in the generation of separated photoinduced reductive electrons (e – ) and oxidative holes (h + ), which subsequently trigger the formation of Ti 3+ species/oxygen vacancies (Ov) and then interfacial Pd–Ov–Ti 3+ sites, affording a Pd/TiO 2 SMSI with enhanced catalytic hydrogenation efficiency. The as-constructed SMSI layer was reversible, and the photodriven procedure could be extended to Pd/ZnO and Pt/TiO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Constructing Ultrathin W-Doped NiFe Nanosheets via Facile Electrosynthesis as Bifunctional Electrocatalysts for Efficient Water Splitting

Exploring cost-effective and efficient bifunctional electrocatalysts via simple fabrication strategies is strongly desired for practical water splitting. Herein, an easy and fast one-step electrodeposition process is developed to fabricate W-doped NiFe (NiFeW)-layered double hydroxides with ultrathin nanosheet features at room temperature and ambient pressure as bifunctional catalysts for water splitting. Notably, the NiFeW nanosheets require overpotentials of only 239 and 115 mV for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), respectively, to reach a current density of 10 mA/cm 2 in alkaline media. Their exceptional performance is further demonstrated in a full electrolyzer configuration with the NiFeW as both anode and cathode catalysts, which achieves a low cell voltage of 1.59 V at 10 mA/cm 2 , 110 mV lower than that of the commercial IrO 2 (anode) and Pt (cathode) catalysts. Moreover, the NiFeW nanosheets are superior to various recently reported bifunctional electrocatalysts. Such remarkable performances mainly ascribe to W doping, which not only effectively modulates the electrocatalyst morphology but also engineers the electronic structure of NiFe hydroxides to boost charge-transfer kinetics for both the OER and HER. Hence, the ultrathin NiFeW nanosheets with an efficient fabrication strategy are promising as bifunctional electrodes for alkaline water electrolyzers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Polymer, Additives, and Processing Effects on N95 Filter Performance

The current severe acute respiratory syndrome coronavirus 2 (SARS-COV-2) pandemic has highlighted the need for personal protective equipment, specifically filtering facepiece respirators like N95 masks. While it is common knowledge that polypropylene (PP) is the industry standard material for filtration media, trial and error is often required to identify suitable commercial precursors for filtration media production. This work aims to identify differences between several commercial grades of PP and demonstrate the development of N95 filtration media with the intent that the industry partners can pivot and help address N95 shortages. Three commercial grades of high melt flow index PP were melt blown at Oak Ridge National Laboratory and broadly characterized by several methods including differential scanning calorimetry (DSC), X-ray diffraction (XRD), and neutron scattering. Despite the apparent similarities (high melt flow and isotacticity) between PP feedstocks, the application of corona charging and charge enhancing additives improve each material to widely varying degrees. From the analysis performed here, the most differentiating factor appears to be related to crystallization of the polymer and the resulting electret formation. Materials with higher crystallization onset temperatures, slower crystallization rates, and larger number of crystallites form a stronger electret and are more effective at filtration.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Ultrathin platinum nanowire based electrodes for high-efficiency hydrogen generation in practical electrolyzer cells

Significant reduction of noble metal catalyst loading and simplification of electrode fabrication are urgently needed in order to lower the cost of proton exchange membrane electrolyzer cells (PEMECs) for large-scale hydrogen production. Herein, we report an integrated electrode design comprising in-situ grown platinum nanowires (PtNW) on ultrathin titanium liquid/gas diffusion layers (LGDLs) via a cost-effective and green chemical synthesis approach. The ultrathin integrated PtNW electrodes showed a low cell voltage of 1.643 V and high efficiency of 90.08% at 1000 mA cm -2 using about 15 times lower catalyst loadings than a conventional catalyst-coated membrane in PEMEC tests. Ex-situ electrochemical characterizations and microscale visualizations further reveal that PtNW electrodes display highly efficient hydrogen evolution reactions and excellent electrode durability due to high active surface area, favorable bubble detachment, and structural stability. This work provides new insights into catalyst layer design and facile ultrathin electrode fabrication for more compact and low-cost PEM electrolyzers, fuel cells and other systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗