Engineering Papers⌕ Search

Engineering topics

Meyer, G.

Publications and source records attributed to Meyer, G..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

The design of exact nonlinear model followers

A practical approach to the design of control systems for strongly nonlinear, multivariable, time-dependent plants is described. The structure of the control system is that of an exact model follower. The model dynamics are decoupled, linear, constant, and of the order of the plant. The plant state and controls are transformed so that the plant, when viewed through these transformations, looks like the simple model. Regulation of disturbances is accomplished by means of the transformed state and controls. Conditions for transformability into linear models, the appropriate models, and the construction of the transformations are discussed. The approach is illustrated on a trajectory autopilot for a helicopter.

Meyer, G.↗
NASA NTRS1981

Application of the concept of dynamic trim control and nonlinear system inverses to automatic control of a vertical attitude takeoff and landing aircraft

A full envelope automatic flight control system based on nonlinear inverse systems concepts has been applied to a vertical attitude takeoff and landing (VATOL) fighter aircraft. A new method for using an airborne digital aircraft model to perform the inversion of a nonlinear aircraft model is presented together with the results of a simulation study of the nonlinear inverse system concept for the vertical-attitude hover mode. The system response to maneuver commands in the vertical attitude was found to be excellent; and recovery from large initial offsets and large disturbances was found to be very satisfactory.

Smith, G. A.↗
NASA NTRS1981

RAMP - A fault tolerant distributed microcomputer structure for aircraft navigation and control

Design methodologies for realizing future high authority autoflight control systems are being investigated, taking into account also the study of distributed microcomputer architectures. Attention is given to the redundant asynchronous microprocessor (RAMP) structure. RAMP comprises a connected network of microcomputers which has as input command and sensor information, and which generates servo information to drive actuators, and thrust linkages. Tolerance to hardware failures is achieved by static redundancy. Results of a failed microcomputer are simply rejected. This is done in lieu of dynamic redundancy wherein the distributed computer system performs real time fault detection and reconfiguration of the system. Attention is given to the RAMP network structure and operation, flight control with parallel asynchronous computers, and intermittent fault tolerance.

Dunn, W. R.↗
NASA NTRS1980

Application of the concept of dynamic trim control to automatic landing of carrier aircraft

The results of a simulation study of an alternative design concept for an automatic landing control system are presented. The alternative design concept for an automatic landing control system is described. The design concept is the total aircraft flight control system (TAFCOS). TAFCOS is an open loop, feed forward system that commands the proper instantaneous thrust, angle of attack, and roll angle to achieve the forces required to follow the desired trajector. These dynamic trim conditions are determined by an inversion of the aircraft nonlinear force characteristics. The concept was applied to an A-7E aircraft approaching an aircraft carrier. The implementation details with an airborne digital computer are discussed. The automatic carrier landing situation is described. The simulation results are presented for a carrier approach with atmospheric disturbances, an approach with no disturbances, and for tailwind and headwind gusts.

Smith, G. A.↗
NASA NTRS1979

Configuration management and automatic control of an augmentor wing aircraft with vectored thrust

An advanced structure for automatic flight control logic for powered-lift aircraft operating in terminal areas is under investigation at Ames Research Center. This structure is based on acceleration control; acceleration commands are constructed as the sum of acceleration on the reference trajectory and a corrective feedback acceleration to regulate path tracking errors. The central element of the structure, termed a Trimmap, uses a model of the aircraft aerodynamic and engine forces to calculate the control settings required to generate the acceleration commands. This report describes the design criteria for the Trimmap and derives a Trimmap for Ames experimental augmentor wing jet STOL research aircraft.

Cicolani, L. S.↗
NASA NTRS1979

Total aircraft flight-control system - Balanced open- and closed-loop control with dynamic trim maps

The availability of the airborne digital computer has made possible a Total Aircraft Flight Control System (TAFCOS) that uses virtually the complete nonlinear propulsive and aerodynamic data for the aircraft to construct dynamic trim maps that represent an inversion of the aircraft model. The trim maps, in series with the aircraft, provide essentially a linear feed-forward path. Basically, open-loop trajectory control is employed with only a small perturbation feedback signal required to compensate for inaccuracy in the aircraft model and for external disturbances. Simulation results for application to an automatic carrier-landing system are presented. Flight-test results for a STOL aircraft operating automatically over a major portion of its flight regime are presented. The concept promises a more rapid and straightforward design from aerodynamic principles, particularly for highly nonlinear configurations, and requires substantially less digital computer capacity than conventional automatic flight-control system designs.

Smith, G. A.↗
NASA NTRS1976

Methodology for design of active controls for V/STOL aircraft

An effort to develop techniques for the design of integrated, fully automatic flight control systems for powered lift STOL and VTOL aircraft is described. The structure is discussed of the control system which has been developed to deal with the strong nonlinearities inherent in this class of aircraft, to admit automatic coupling with the advanced ATC requiring accurate execution of complex trajectories, and to admit a variety of active control tasks. The specific case considered is the Augmentor Wing Research Aircraft.

Meyer, G.↗
NASA NTRS1975

A formal structure for advanced automatic flight-control systems

Techniques were developed for the unified design of multimode, variable authority automatic flight-control systems for powered-lift STOL and VTOL aircraft. A structure for such systems is developed to deal with the strong nonlinearities inherent in this class of aircraft, to admit automatic coupling with advanced air traffic control, and to admit a variety of active control tasks. The aircraft being considered is the augmentor wing jet STOL research aircraft.

Meyer, G.↗
NASA NTRS1975

Digital simulation of V/STOL aircraft for autopilot research

Simulations of V/STOL aircraft for autopilot research were introduced as examples of large scale systems. A hierarchy of simulations was assembled, and a modular organization was given to the simulations. The dynamics of the system were subdivided into translational and rotational degrees of freedom, based on the different frequencies at which significant variations in motion variables, control forces and moments occur in two subsystems. This is the basis of the autopilot partitioning into two smaller control problems.

Cicolani, L. S.↗
NASA NTRS1975

NASA Ames Active Control Aircraft flight experiments (ACA) program

The objectives of the Ames ACA program are to develop the active control technology (ACT) for short-haul aircraft, to evaluate existing methods, to develop new techniques, and to demonstrate the readiness of the technology in operational environment. Two concepts are basic to ACT: integrated aircraft design and integrated flight-control-system design.

Meyer, G.↗