Engineering topics

Melson, N. D.

Publications and source records attributed to Melson, N. D..

9 records

NASA NTRS1993

Time-accurate Navier-Stokes calculations with multigrid acceleration

An efficient method for calculating unsteady flows is presented, with emphasis on a modified version of the thin-layer Navier-Stokes equations. Fourier stability analysis is used to illustrate the effect of treating the source term implicitly instead of explicity, as well as to illustrate other algorithmic choices. A 2D circular cylinder (with a Reynolds number of 1200 and a Mach number of 0.3) is calculated. The present scheme requires only about 10 percent of the computer time required by global minimum time stepping.

Melson, N. D.↗

NASA NTRS1991

A three dimensional multigrid multiblock multistage time stepping scheme for the Navier-Stokes equations

A general multiblock method for the solution of the three-dimensional, unsteady, compressible, thin-layer Navier-Stokes equations has been developed. The convective and pressure terms are spatially discretized using Roe's flux differencing technique while the viscous terms are centrally differenced. An explicit Runge-Kutta method is used to advance the solution in time. Local time stepping, adaptive implicit residual smoothing, and the Full Approximation Storage (FAS) multigrid scheme are added to the explicit time stepping scheme to accelerate convergence to steady state. Results for three-dimensional test cases are presented and discussed.

Elmiligui, Alaa↗

NASA NTRS1986

Vectorizable multigrid algorithms for transonic-flow calculations

The analysis and the incorporation into a multigrid scheme of several vectorizable algorithms are discussed. von Neumann analyses of vertical-line, horizontal-line, and alternating-direction ZEBRA algorithms were performed; and the results were used to predict their multigrid damping rates. The algorithms were then successfully implemented in a transonic conservative full-potential computer program. The convergence acceleration effect of multiple grids is shown, and the convergence rates of the vectorizable algorithms are compared with those of standard successive-line overrelaxation (SLOR) algorithms.

Melson, N. D.↗

NASA NTRS1985

Vectorizable multigrid algorithms for transonic flow calculations

The analysis and incorporation into a multigrid scheme of several vectorizable algorithms are discussed. Von Neumann analyses of vertical line, horizontal line, and alternating direction ZEBRA algorithms were performed; and the results were used to predict their multigrid damping rates. The algorithms were then successfully implemented in a transonic conservative full-potential computer program. The convergence acceleration effect of multiple grids is shown and the convergence rates of the vectorizable algorithms are compared to the convergence rates of standard successive line overrelaxation (SLOR) algorithms.

Melson, N. D.↗

NASA NTRS1983

TAWFIVE: A user's guide

The Transonic Analysis of a Wing and Fuselage with Interacted Viscous Effects (TAWFIVE) was developed. A finite volume full potential method is used to model the outer inviscid flow field. First-order viscous effects are modeled by a three dimensional integral boundary layer method. Both turbulent and laminar boundary layers are treated. Wake thickness and curvature effects are modeled using a two dimensional strip method. A very brief discussion of the engineering aspects of the program is given. The input and use of the program are covered in great detail.

Melson, N. D.↗

NASA NTRS1983

Use of CYBER 203 and CYBER 205 computers for three-dimensional transonic flow calculations

Experiences are discussed for modifying two three-dimensional transonic flow computer programs (FLO 22 and FLO 27) for use on the CDC CYBER 203 computer system. Both programs were originally written for use on serial machines. Several methods were attempted to optimize the execution of the two programs on the vector machine: leaving the program in a scalar form (i.e., serial computation) with compiler software used to optimize and vectorize the program, vectorizing parts of the existing algorithm in the program, and incorporating a vectorizable algorithm (ZEBRA I or ZEBRA II) in the program. Comparison runs of the programs were made on CDC CYBER 175. CYBER 203, and two pipe CDC CYBER 205 computer systems.

Melson, N. D.↗

NASA NTRS1982

Experiences in using the CYBER 203 for three-dimensional transonic flow calculations

In this paper, the authors report on some of their experiences modifying two three-dimensional transonic flow programs (FLO22 and FLO27) for use on the NASA Langley Research Center CYBER 203. Both of the programs discussed were originally written for use on serial machines. Several methods were attempted to optimize the execution of the two programs on the vector machine, including: (1) leaving the program in a scalar form (i.e., serial computation) with compiler software used to optimize and vectorize the program, (2) vectorizing parts of the existing algorithm in the program, and (3) incorporating a new vectorizable algorithm (ZEBRA I or ZEBRA II) in the program.

Melson, N. D.↗

NASA NTRS1982

Flow through the tile gaps in the Space Shuttle Thermal Protection System

The problem of predicting aerodynamic loads on the insulating tiles of the Space Shuttle Thermal Protection System (TPS) is discussed and seen to require a method for predicting pressure and mass flux in the gaps between tiles. A mathematical model of the tile-gap flow is developed based upon a slow viscous (Stokes) flow analysis and is verified against available experimental data. This model derives the tile-gap pressure field from a solution of the two-dimensional Laplace equation; the mass flux vector is then calculated from the pressure gradient. The means for incorporating this model into a lumped-parameter network analogy for porous-media flow is also given. The flow model shows tile-gap mass flux to be very sensitive to the gap width indicating a need for coupling the TPS flow and tile displacement calculations. Finally recommendations are made concerning additional analytical and experimental work to improve TPS flow predictions.

Dwoyer, D. L.↗

NASA NTRS1981

A title-gap flow model for use in aerodynamic loads assessment of space shuttle thermal protection system: Parallel gap faces

The problem of predicting aerodynamic loads on the insulating tiles of the space shuttle thermal protection system (TPS) is discussed and seen to require a method for predicting pressure and mass flux in the gaps between tiles. A mathematical model of the tile-gap flow is developed, based upon a slow viscous (Stokes) flow analysis, and is verified against experimental data. The tile-gap pressure field is derived from a solution of the two-dimensional Laplace equation; the mass-flux vector is then calculated from the pressure gradient. The means for incorporating this model into a lumped-parameter network analogy for porous-media flow is given. The means for incorporating this model into a lumped-parameter network analogy for porous-media flow is given. The flow model shows tile-gap mass flux to be very sensitive to the gap width indicating a need for coupling the TPS flow and tile displacement calculation. Analytical and experimental work to improve TPS flow predictions and a possible shuttle TPS hardware modification are recommended.

Dwoyer, D. L.↗