Engineering topics

Meelan M Choudhari

Publications and source records attributed to Meelan M Choudhari.

At least 37 records · Page 2

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗

NASA NTRS2020

Convolutional Neural Network for Transition Modeling Based on Linear Stability Theory

Transition prediction is an important aspect of aerodynamic design because of its impact on skin friction and potential coupling with flow separation characteristics. Traditionally, the modeling of transition has relied on correlation-based empirical formulas based on integral quantities such as the shape factor of the boundary layer. However, in many applications of computational fluid dynamics, the shape factor is not straightforwardly available or not well-defined. We propose using the complete velocity profile along with other quantities (e.g., frequency, Reynolds number) to predict the perturbation amplification factor. While this can be achieved with regression models based on a classical fully connected neural network, such a model can be computationally more demanding. We propose a novel convolutional neural network inspired by the underlying physics as described by the stability equations. Specifically, convolutional layers are first used to extract integral quantities from the velocity profiles, and then fully connected layers are used to map the extracted integral quantities, along with frequency and Reynolds number, to the output (amplification ratio). Numerical tests on classical boundary layers clearly demonstrate the merits of the proposed method. More importantly, we demonstrate that, for Tollmien-Schlichting instabilities in two-dimensional, low-speed boundary layers, the proposed network encodes information in the boundary layer profiles into an integral quantity that is strongly correlated to a well-known, physically defined parameter – the shape factor.

Laminar-turbulent transition↗

NASA NTRS2020

Shape Optimization of Vortex Generators to Control Mack Mode Amplification

This paper demonstrates the potential to use shape optimization for the design of vortex generators in an axisymmetric boundary layer. This shape optimization increases the amplitude of stationary streaks created by streamwise vorticity, with the goal of reducing the amplification of Mack mode instabilities. The test case under consideration matches a trajectory point during the ascent phase of the HIFiRE-1 flight experiment. Wall-mounted vortex generators are added to the cone and their shape is optimized to control the amplification of Mack mode instabilities that are known to initiate laminar-turbulent transition in this flow. An empirical objective function is developed based on the previous studies of optimal streaks. A constraint on the maximum streak amplitude is added to avoid the initiation of bypass transition. The shape optimization is conducted using SU2, an open-source suite for multiphysics simulation and design. A significant improvement is observed in an integral metric of the streak amplitude, while the maximum streak amplitude is maintained close to the baseline level. The qualitative features of the optimized geometry are discussed.

Vortex generators↗

NASA NTRS2020

Simulation and Modeling of Cold-Wall Hypersonic Turbulent Boundary Layers on Flat Plate

Direct numerical simulations (DNS) of flat-plate, zero-pressure-gradient turbulent boundary layers are presented for nominal freestream Mach numbers of 11 and 14 and a highly cooled wall (wall-to-recovery temperature of approximately 0.2). The flow conditions of the DNS are representative of the experimental data for a Mach 11.1 turbulent boundary layer on a flat plate that was tested at Calspan–University of Buffalo Research Center (CUBRC) and the operational conditions of the AEDC Hypervelocity Tunnel No. 9 at Mach 14. The wall shear stress and turbulent heat flux predicted by DNS show good comparisons with those measured at CUBRC and those modeled with a Baldwin-Lomax model. The generated DNS database extends the range of Reynolds numbers from those typical of previous DNS studies for hypersonic boundary-layer flows and confirms the validity of Morkovin’s hypothesis within the relatively broader range of Reynolds numbers considered in this study. A priori assessment of turbulent heat flux models with DNS data shows that the algebraic energy flux (AEF) formulation gives better predictions of the streamwise turbulent heat flux than the commonly used constant turbulent Prandtl number model while both models give similarly good predictions of the wall-normal turbulent heat flux. A posteriori assessment shows that the AEF model improves the prediction of the temperature profiles while keeping a good prediction of the velocity field.

Junji Huang↗

NASA NTRS2020

Toward Transition Modeling in a Hypersonic Boundary Layer at Flight Conditions

An accurate physics-based transition prediction method integrated with computational fluid dynamics (CFD) solvers is pursued for hypersonic boundary layer flows over slender hypersonic vehicles at flight conditions. The geometry and flow conditions are selected to match relevant trajectory locations from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach numbers in the range of 3.8 – 5.5 and freestream unit Reynolds numbers in the range of 3.3 × 10(exp 6) – 21.4 × 10(exp 6) m(exp -1). Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment correlated with an amplification factor of N ≈ 13.5 for the planar Mack modes. However, to incorporate the N-factor correlations into a CFD code, we investigate surrogate models for disturbance amplification that avoid the direct computation of stability characteristics. A commonly used approach for low-speed flows is based on an a priori database of stability characteristics for locally similar profiles. However, the results presented in this paper demonstrate that the application of this approach to hypersonic boundary layers over blunt spherical nose-tip cones leads to large, unacceptable errors in the predictions of amplification factors, mainly due to its failure in accounting for the effects of the entropy layer on the boundary-layer profiles along the length of the model. We propose and demonstrate an alternate approach that employs the stability computations for a canonical set of blunt cone configurations to train a physics-informed convolutional neural network model that is shown to provide substantially improved transition predictions for hypersonic flow configurations with entropy-layer effects. Furthermore, the excellent performance of the neural network model is also confirmed for cone configurations with nose radius and half-angle values that do not correspond to those used to build the database. Finally, the convolutional neural network model is shown to outperform the linear stability calculations for underresolved basic states.

Pedro Paredes↗

NASA NTRS2019

Laminar-Turbulent Transition Upstream of the Entropy-Layer Swallowing Location in Hypersonic Boundary Layers

Numerical and experimental studies have demonstrated that modal growth of planar Mack modes is responsible for laminar-turbulent transition on sharp cones at hypersonic speeds. However, the physical mechanisms that lead to transition onset upstream of the entropy-layer swallowing location over sufficiently blunt geometries are not well understood as yet. Modal amplification is too weak or nonexistent to initiate transition at moderate-to-large bluntness values. Nonmodal analysis shows that, with increasing nose bluntness, both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification. However, because of the relatively weak signature of the nonmodal traveling disturbances within the boundary-layer region, the route to transition onset subsequent to the nonmodal growth remains unclear. Thus, nonlinear parabolized stability equations (NPSE) and direct numerical simulations (DNS) have been used to investigate the potential transition mechanisms over a 7-degree blunt cone that was tested in the AFRL Mach-6 high-Reynoldsnumber facility. Computations are performed to separately follow the nonlinear development of two classes of inflow disturbances, namely, a pair of oblique traveling waves with equal but opposite angles with respect to the mean flow direction and a planar traveling wave. Results in both cases show an excellent agreement between the NPSE and DNS predictions, establishing that the NPSE is an accurate and efficient technique for predicting the nonlinear development for these particular nonmodal traveling disturbances. Computations reveal that the oblique mode interactions lead to the generation of stationary streaks inside the boundary layer that, in turn, facilitate the growth of a subharmonic sinuous disturbance. For relatively modest amplitudes of the inflow disturbance, the oblique-mode breakdown can lead to transition at the measured location of transition onset during the experiment. On the other hand, the nonlinear development of a planar traveling wave leads to the formation of inclined structures just above the boundary-layer edge and these structures are strongly reminiscent of the transitional events observed during blunt cone experiments by using schlieren flow visualizations.

Entropy↗

NASA NTRS2019

Numerical Investigation of Roughness Effects on Transition on Spherical Capsules

To address the hitherto unknown mechanism of boundary-layer transition on blunt reentry capsules, the role of roughness-induced disturbance growth on a spherical-section forebody is assessed via optimal transient growth theory and direct numerical simulations (DNS). Optimal transient-growth studies have been performed for the blunt capsule experiments at Mach 5.9 in the Hypersonic Ludwieg tube at the Technische Universität Braunschweig (HLB), which included measurements behind a patch of controlled, distributed micron-sized surface roughness. Transient-growth results for the HLB capsule indicate similar trends as the corresponding numerical data for a Mach 6 experiment in the Actively Controlled Expansion (ACE) facility of the Texas A&M University (TAMU) at a lower Reynolds number. Both configurations indicate a similar dependence on surface temperature ratio and, more important, rather low values of maximum energy gain. DNS are performed for the conditions of the HLB experiment to understand the generation of stationary disturbances by the roughness patch and the accompanying evolution of unsteady perturbations. However, no evidence of either modal or nonmodal disturbance growth in the wake of the roughness patch is found in the DNS data; thus, the physical mechanism underlying the observed onset of transition still remains unknown.

Stefan Hein↗

NASA NTRS2019

Nonmodal Growth of TravelingWaves on Blunt Cones at Hypersonic Speeds

The existing database of transition measurements in hypersonic ground facilities has established that, as the nosetip bluntness is increased, the onset of boundary layer transition over a circular cone at zero angle of attack shifts downstream. However, this trend is reversed at sufficiently large values of the nose Reynolds number, so that the transition onset location eventually moves upstream with a further increase in nose-tip bluntness. Because modal amplification is too weak to initiate transition at moderate-to-large bluntness values, nonmodal growth has been investigated as the potential basis for a physics-based model for the frustum transition. The present analysis investigates the nonmodal growth of traveling disturbances initiated within the nose-tip vicinity that peak within the entropy layer. Results show that, with increasing nose bluntness, both planar and oblique traveling disturbances experience appreciable energy amplification up to successively higher frequencies. For moderately blunt cones, the initial nonmmodal growth is followed by a partial decay that is more than overcome by an eventual, modal growth as Mack-mode waves. For larger bluntness values, the Mack-mode waves are not amplified anywhere upstream of the experimentally measured transition location, but the traveling modes still undergo a significant amount of nonmodal growth. This finding does not provide a definitive link between optimal growth and the onset of transition, but it is qualitatively consistent with the experimental observations that frustum transition in the absence of sufficient Mack-mode amplification implies a double peak in disturbance amplification and the appearance of transitional events above the boundary-layer edge.

Hypersonic speed↗

NASA NTRS2018

Nosetip Bluntness Effects on Transition at Hypersonic Speeds: Experimental and Numerical Analysis

The existing database of transition measurements in hypersonic ground facilities has established that the onset of boundary layer transition over a circular cone at zero angle of attack shifts downstream as the nosetip bluntness is increased with respect to a sharp cone. However, this trend is reversed at sufficiently large values of the nosetip Reynolds number, so that the transition onset location eventually moves upstream with a further increase in nosetip bluntness. This transition reversal phenomenon, which cannot be explained on the basis of linear stability theory, was the focus of a collaborative investigation under the NATO STO group AVT-240 on Hypersonic Boundary-Layer Transition Prediction. The current paper provides an overview of that effort, which included wind tunnel measurements in three different facilities and theoretical analysis related to modal and nonmodal amplification of boundary layer disturbances. Because neither first and second-mode waves nor entropy-layer instabilities are found to be substantially amplified to initiate transition at large bluntness values, transient (i.e., nonmodal) disturbance growth has been investigated as the potential basis for a physics based model for the transition reversal phenomenon. Results of the transient growth analysis indicate that stationary disturbances that are initiated within the nosetip or in the vicinity of the juncture between the nosetip and the frustum can undergo relatively significant nonmodal amplification and that the maximum energy gain increases nonlinearly with the nose radius of the cone. This finding does not provide a definitive link between transient growth and the onset of transition, but it is qualitatively consistent with the experimental observations that frustum transition during the reversal regime was highly sensitive to wall roughness, and furthermore, was dominated by disturbances that originated near the nosetip. Furthermore, the present analysis shows significant nonmodal growth of traveling disturbances that peak within the entropy layer and could also play a role in the transition reversal phenomenon.

Freestream Mach Number↗

NASA NTRS2018

Instability Wave–Streak Interactions in a High Mach Number Boundary Layer at Flight Conditions

The interaction of stationary streaks undergoing nonmodal growth with modally unstable instability waves in a hypersonic boundary-layer flow is studied using numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment; namely, a 7 degree half-angle, circular cone with 2.5 mm nose radius, freestream Mach number equal to 5.30, unit Reynolds number equal to 13.42 m -1 , and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the vehicle. This paper investigates the nonlinear evolution of initially linear optimal disturbances that evolve into finite-amplitude streaks, followed by an analysis of the modal instability characteristics of the perturbed, streaky boundary-layer flow. The investigation is performed with stationary direct numerical simulations (DNS) and plane-marching parabolized stability equations (PSE), in conjunction with partial-differential-equation-based planar eigenvalue analysis. The overall effect of streaks is to reduce the peak amplification factors of instability waves, indicating a possible downstream shift in the onset of laminar-turbulent transition. The present study confirms previous findings that the mean flow distortion of the nonlinear streak perturbation reduces the amplification rates of the Mack-mode instability. More importantly, however, the present results demonstrate that the spanwise varying component of the streak can produce a larger effect on the Mack-mode amplification. The study with selected azimuthal wavenumbers for the stationary streaks reveals that a wavenumber of approximately 1.4 times larger than the optimal wavenumber is more effective in stabilizing the planar Mack-mode instabilities. In the absence of unstable first-mode waves for the present cold-wall condition, transition onset is expected to be delayed until the peak streak amplitude increases to nearly 35 percent of the freestream velocity, when intrinsic instabilities of the boundary-layer streaks begin to dominate the transition process. For streak amplitudes below that limit a significant net stabilization is achieved, yielding a potential transition delay that can exceed 100 percent of the length of the laminar region in the uncontrolled case.

Boundary layer stability↗

NASA NTRS2018

Transition Delay via Vortex Generators in a Hypersonic Boundary Layer at Flight Conditions

The potential of realizable, stationary streaks undergoing non-modal growth to stabilize a hypersonic boundary-layer flow and, subsequently, delay the laminar-turbulent transition onset, is studied via numerical computations. The geometry and flow conditions are selected to match a relevant trajectory location from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach number of 5.30, freestream unit Reynolds number equal to 13.42 x 10(exp 6)/m, and wall-to-adiabatic temperature ratio of approximately 0.35 over most of the test article. This paper investigates flow modifications induced by wall-mounted vortex generators (VGs), followed by an analysis of the modal instability of the perturbed, streaky boundary-layer flow. Results are presented both for a single array of VGs that was designed on the basis of optimal growth theory and for a VG configuration involving two separate arrays with opposite orientations that ware designed to provide staged control of flow instabilities while simultaneously reducing the amplification of streak instabilities resulting from the control devices. Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment, which did not include any control devices, correlated with an amplification factor of N = 14.7 for the planar Mack modes. If one assumes that the transition N -factor is not affected by the introduction of the VGs, then the control configurations based on a single array of VGs and two separate arrays would result in a transition delay of 17% and 40%, respectively. These findings suggest a passive flow control s to induce streaks that would delay transition in hypersonic boundary dominated by Mack-mode instabilities.

Incompressible boundary layer↗

NASA NTRS2018

Blunt-Body Paradox and Improved Application of Transient-Growth Framework

The “Reshotko-Tumin transition criterion" based on optimal transient growth successfully correlates laboratory measurements of roughness induced transition over blunt body configurations. Even though transient growth has not been conclusively linked to the measured onset of transition, the above correlation denotes the only available physics-based model for subcritical transition in blunt body flows, since the latter do not support any modal instabilities at typical experimental conditions. Unlike other established models based on empirical curve fits that are valid for a specific subclass of datasets, the optimal-growth-based transition criterion appears to provide a reasonable correlation with measurements in various wind tunnel and ballistic range facilities and for a broad range of surface temperature ratios. This paper is focused on optimal growth calculations that improve upon significant shortcomings of the computations underlying the Reshotko-Tumin correlation. The improved framework is applied to leeward transition over a spherical section forebody that was tested in the Mach 6 Adjustable Contour Expansion wind tunnel at Texas A&M University. The computed results highlight the significance of nonparallel basic state evolution, curvature terms, and an optimization procedure that varies both inflow and outflow locations of the transient growth interval. More important, the results indicate that the modified correlation is very close to its original form, and hence, that the accuracy of the transient-growth-based transition criterion is not compromised by using a more thorough theoretical framework. Yet the results also show that the optimal energy gain up to the predicted transition onset location can be rather small, highlighting the need to further investigate the optimal growth criterion for additional experimental configurations and to also uncover the in-depth physics underlying blunt body transition.

Freestream conditions↗

NASA NTRS2018

Nosetip Bluntness Effects on Transition at Hypersonic Speeds: Experimental and Numerical Analysis Under NATO STO AVT-240

The existing database of transition measurements in hypersonic ground facilities has established that the onset of boundary layer transition over a circular cone at zero angle of attack shifts downstream as the nosetip bluntness is increased with respect to a sharp cone. However, this trend is reversed at sufficiently large values of the nosetip Reynolds number, so that the transition onset location eventually moves upstream with a further increase in nosetip bluntness. This transition reversal phenomenon, which cannot be explained on the basis of linear stability theory, was the focus of a collaborative investigation under the NATO STO group AVT-240 on Hypersonic Boundary-Layer Transition Prediction. The current paper provides an overview of that effort, which included wind tunnel measurements in three different facilities and theoretical analysis related to modal and nonmodal amplification of boundary layer disturbances. Because neither first and second-mode waves nor entropy-layer instabilities are found to be substantially amplified to initiate transition at large bluntness values, transient (i.e., nonmodal) disturbance growth has been investigated as the potential basis for a physics-based model for the transition reversal phenomenon. Results of the transient growth analysis indicate that disturbances that are initiated within the nosetip or in the vicinity of the juncture between the nosetip and the frustum can undergo relatively significant nonmodal amplification and that the maximum energy gain increases nonlinearly with the nose radius of the cone. This finding does not provide a definitive link between transient growth and the onset of transition, but it is qualitatively consistent with the experimental observations that frustum transition during the reversal regime was highly sensitive to wall roughness, and furthermore, was dominated by disturbances that originated near the nosetip.

Numerical analysis↗

NASA NTRS2017

Instability Wave-Streak Interactions in a Supersonic Boundary Layer

Optimal initial conditions for transient growth in a two-dimensional boundary layer flow correspond to stationary, counter-rotating vortices that subsequently develop into streamwise elongated streaks, which are characterized by an alternating pattern of low and high streamwise velocity. For incompressible flows, previous studies have shown that boundary layer modulation due to streaks below a threshold amplitude level can stabilize the Tollmien-Schlichting instability waves, resulting in a delay in the onset of laminar-turbulent transition. In the supersonic regime, the linearly, most-amplified waves become three-dimensional, corresponding to oblique, first-mode waves. This change in the character of dominant instabilities leads to an important change in the transition process, which is now dominated by oblique breakdown via nonlinear interactions between pairs of first-mode waves that propagate at equal but opposite angles with respect to the free stream. Because the oblique breakdown process is characterized by a rapid amplification of stationary streamwise streaks, artificial excitation of such streaks may be expected to promote transition in a supersonic boundary layer. Indeed, suppression of those streaks has been shown to delay the onset of transition in prior literature. Consistent with those findings, the present study shows that optimally growing stationary streaks indeed destabilize the first-mode waves, but only when the spanwise wavelength of the instability waves is equal to or smaller than twice the streak spacing. Transition in a benign disturbance environment typically involves first-mode waves with significantly longer spanwise wavelengths, and hence, these waves are stabilized by the optimal growth streaks. Thus, as long as the amplification factors for the destabilized, short wavelength instability waves remain below the threshold level for transition, a significant net stabilization is achieved, yielding a transition delay that is comparable to the length of the laminar region in the uncontrolled case.

Boundary layer transition↗

NASA NTRS2017

Stabilization of Hypersonic Boundary Layers by Linear and Nonlinear Optimal Perturbations

The effect of stationary, finite-amplitude, linear and nonlinear optimal perturbations on the modal disturbance growth in a Mach 6 axisymmetric flow over a 7 deg. half-angle cone with 0:126 mm nose radius and 0:305 m length is investigated. The freestream parameters (M = 6, Re(exp 1) = 18 x 10(exp. 6) /m) are selected to match the flow conditions of a previous experiment in the VKI H3 hypersonic tunnel. Plane-marching parabolized stability equations are used in conjunction with a partial-differential equation based planar eigenvalue analysis to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode and first-mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone; however, subharmonic first-mode instabilities, which are destabilized by the presence of the streaks, do reach N = 6 near the end of the cone. The highest stabilization is observed at streak amplitudes of approximately 20 percent of the freestream velocity. Because the use of initial disturbance profiles based on linear optimal growth theory may yield suboptimal control in the context of nonlinear streaks, the computational predictions are extended to nonlinear optimal growth theory. Results show that by using nonlinearly optimal perturbation leads to slightly enhanced stabilization of plane Mack mode disturbances as well as reduced destabilization of subharmonic first-mode disturbances.

Incompressible boundary layer↗

NASA NTRS2016

Pressure Fluctuations Induced by a Hypersonic Turbulent Boundary Layer

Direct numerical simulations (DNS) are used to examine the pressure fluctuations generated by a spatially-developed Mach 5.86 turbulent boundary layer. The unsteady pressure field is analyzed at multiple wall-normal locations, including those at the wall, within the boundary layer (including inner layer, the log layer, and the outer layer), and in the free stream. The statistical and structural variations of pressure fluctuations as a function of wall-normal distance are highlighted. Computational predictions for mean velocity pro les and surface pressure spectrum are in good agreement with experimental measurements, providing a first ever comparison of this type at hypersonic Mach numbers. The simulation shows that the dominant frequency of boundary-layer-induced pressure fluctuations shifts to lower frequencies as the location of interest moves away from the wall. The pressure wave propagates with a speed nearly equal to the local mean velocity within the boundary layer (except in the immediate vicinity of the wall) while the propagation speed deviates from the Taylor's hypothesis in the free stream. Compared with the surface pressure fluctuations, which are primarily vortical, the acoustic pressure fluctuations in the free stream exhibit a significantly lower dominant frequency, a greater spatial extent, and a smaller bulk propagation speed. The freestream pressure structures are found to have similar Lagrangian time and spatial scales as the acoustic sources near the wall. As the Mach number increases, the freestream acoustic fluctuations exhibit increased radiation intensity, enhanced energy content at high frequencies, shallower orientation of wave fronts with respect to the flow direction, and larger propagation velocity.

Lian Duan↗

NASA NTRS2016

Optimal Growth in Hypersonic Boundary Layers

The linear form of the parabolized linear stability equations is used in a variational approach to extend the previous body of results for the optimal, nonmodal disturbance growth in boundary-layer flows. This paper investigates the optimal growth characteristics in the hypersonic Mach number regime without any high-enthalpy effects. The influence of wall cooling is studied, with particular emphasis on the role of the initial disturbance location and the value of the spanwise wave number that leads to the maximum energy growth up to a specified location. Unlike previous predictions that used a basic state obtained from a self-similar solution to the boundary-layer equations, mean flow solutions based on the full Navier-Stokes equations are used in select cases to help account for the viscous- inviscid interaction near the leading edge of the plate and for the weak shock wave emanating from that region. Using the full Navier-Stokes mean flow is shown to result in further reduction with Mach number in the magnitude of optimal growth relative to the predictions based on the self-similar approximation to the base flow.

Navier Stokes equations↗

NASA NTRS2016

Nonlinear Transient Growth and Boundary Layer Transition

Parabolized stability equations (PSE) are used in a variational approach to study the optimal, non-modal disturbance growth in a Mach 3 at plate boundary layer and a Mach 6 circular cone boundary layer. As noted in previous works, the optimal initial disturbances correspond to steady counter-rotating streamwise vortices, which subsequently lead to the formation of streamwise-elongated structures, i.e., streaks, via a lift-up effect. The nonlinear evolution of the linearly optimal stationary perturbations is computed using the nonlinear plane-marching PSE for stationary perturbations. A fully implicit marching technique is used to facilitate the computation of nonlinear streaks with large amplitudes. To assess the effect of the finite-amplitude streaks on transition, the linear form of plane- marching PSE is used to investigate the instability of the boundary layer flow modified by spanwise periodic streaks. The onset of bypass transition is estimated by using an N- factor criterion based on the amplification of the streak instabilities. Results show that, for both flow configurations of interest, streaks of sufficiently large amplitude can lead to significantly earlier onset of transition than that in an unperturbed boundary layer without any streaks.

Laminar turbulent transition↗