Engineering topics

Mcronald, A. D.

Publications and source records attributed to Mcronald, A. D..

8 records

NASA NTRS1989

Solar probe mission status

The penetration of coronal regions by a solar probe employing planetary gravity-assist trajectories to attain perihelia of only a few solar radii will allow unique in situ experiments to be conducted. The trajectory design options will fundamentally impact solar probe spacecraft design criteria. The aerogravity-assist method, which requires the bending of a trajectory in the vicinity of a planet by passing through a portion of its atmosphere will yield large changes in direction and velocity. This option would in the case of a solar probe mission involve the use of either the earth or Venus as a target for a specially aerodynamically configured 'waverider' spacecraft with L/D of the order of 10.

Randolph, J. E.↗

NASA NTRS1980

Thermophysical and system integration considerations in aerobraking design

The aerobraking concept for decelerating spacecraft into low-energy orbits is summarized. Data and comparisons are given for aerobraking approaches to Venus, Earth, Mars, and Titan. Calculations are based on adaption of a craft similar to the Venus Orbiting Imaging Radar vehicle to an aerobraking configuration. Special attention is given to integration of the aerobraking parts into the system and protection of the craft from heat loads due to the aerobraking maneuvers.

French, J. R.↗

NASA NTRS1978

Improved electron-beam probe for hypersonic flows

Probe uses differentially-pumped drift tube to connect high and low pressure regions thereby allowing higher gas densities to be studied. System uses higher beam voltages (50 kV) and currents (1 mA delivered to gas), and extends boundary layer penetration up to 15.2 cm, and test duration to one hour.

Mcronald, A. D.↗

NASA NTRS1977

Atmospheric braking to circularize an elliptical Venus orbit

The use of atmospheric drag to circularize an elliptical spacecraft orbit at Venus is analyzed parametrically for the Venus Orbital Imaging Radar Mission (VOIR) in 1983. Navigation, maneuver, and guidance requirements are discussed for the decay of a 24-hr orbit to a close circular orbit in about 30-60 days. A prototype 'Aerobrake' is described which is approximately 5 m in diameter and 25 kg in mass and which replaces a chemical retroengine of about 1300 kg in mass (delta V = 2.5 km/s) by a 700 kg in-orbit mass. The aerobrake, a light deployable Inconel sheet, shields the spacecraft from the flow and radiates the aerodynamic heating.

Mcronald, A. D.↗

NASA NTRS1975

Measurement of density and temperature in a hypersonic turbulent boundary layer using the electron beam fluorescence technique

Mean density and temperature fluctuations were measured across the turbulent, cooled-wall boundary layer in a continuous hypersonic (Mach 9.4) wind tunnel in air, using the nitrogen fluorescence excited by a 50 kV electron beam. Data were taken at three values of the tunnel stagnation pressure, the corresponding free stream densities being equivalent to 1.2, 4.0, and 7.4 torr at room temperature, and the boundary layer thicknesses about 4.0, 4.5, and 6.0 inches. The mean temperature and density profiles were similar to those previously determined in the same facility by conventional probes (static and pitot pressure, total temperature). A static pressure variation of about 50% across the boundary layer was found, the shape of the variation changing somewhat for the three stagnation pressure levels. The quadrupole model for rotational temperature spectra gave closer agreement with the free stream isentropic level (approximately 44 K) than the dipole model.

Mcronald, A. D.↗

NASA NTRS1973

Spacecraft microbial burden reduction due to atmospheric entry heating - Jupiter.

An effort has been underway at Jet Propulsion Laboratory to develop the tools necessary to predict temperature histories for a typical spacecraft during inadvertent entry. In order that the results have general applicability, parametric analyses are performed. The thermal response of the spacecraft components and debris resulting from disintegration is determined. The temperature histories of small particles and composite materials, such as thermal blankets and an antenna, are given special attention. Guidelines are given to indicate the types of components and debris most likely to contain viable organisms, which could contaminate the lower layers of the Jovian atmosphere.

Gonzalez, C. C.↗

NASA NTRS1972

Thin film gauge

A thin film gauge for use in measuring distributed convective heat transfer rates occurring along given surfaces, is described. The gauge is particularly suited to measuring test surfaces in the air stream of a wind tunnel. The gauge is characterized by a plurality of painted platinum leads extend across the surface of a substrate; a pair of leads on the surface is adapted to deliver an electric current at a constant amperage through a selected thermally active area. Leads are also coupled at opposite sides of the thermally active area for detecting induced voltage drops occurring in the area so that the active length of the gauge is defined between voltage output leads. Changes in heat transfer to the thermally active area are isolated and determined by detecting induces changes in voltage drop.

Mcronald, A. D.↗

NASA NTRS1972

On the possibility of Earth reentry simulation of shallow angle Jupiter entry

Possible Earth reentry simulation of shallow-angle (3 to 30 deg) Jupiter entry was investigated in terms of four parameters of the bow shock layer ahead of a blunt vehicle: peak (equilibrium) temperature, peak pressure, peak inward radiative flux, and time-integrated radiative flux. It is shown that simulation ranging from fair to good can be achieved. Reentry is easiest (lowest Earth reentry speed) at steep Earth reentry, in the Earth entry speed range of 15 to 22 km/sec, for both the Jupiter nominal and cool atmospheres. Increased Earth speed is required, generally, for increasing Jupiter entry angle, and for increasing temperature, radiative flux, time-integrated flux and pressure, in that order.

Mcronald, A. D.↗