Engineering topics
McMahon, William E.
Publications and source records attributed to McMahon, William E..
Characterization of multiterminal tandem photovoltaic devices and their subcell coupling
Three-terminal (3T) and four-terminal (4T) tandem photovoltaic (PV) devices using various materials have been increasingly reported in the literature, but measurement standards are lacking. Here, multiterminal devices measured as functions of two load variables are characterized unambiguously as functions of three device voltages or currents on hexagonal plots. We demonstrate these measurement techniques using two GaInP/GaAs tandem solar cells, with a middle contact between the two subcells, as example 3T devices with both series-connected and reverse-connected subcells. Coupling mechanisms between the subcells are quantified within the context of a simple equivalent optoelectronic circuit. Electrical and optical coupling mechanisms are most clearly revealed using coupled dark measurements. These measurements are sensitive enough to observe very small luminescent coupling from the bottom subcell to the top subcell in the prototype 3T device. Quick simplified measurement techniques are also discussed within the context of the complete characterization.
Development of High-Efficiency GaAs Solar Cells Grown on Nanopatterned GaAs Substrates
One approach to reducing the cost of high-efficiency III–V devices involves adding patterned layers to heteroepitaxial or homoepitaxial substrates to facilitate substrate removal and reuse. However, few studies have focused explicitly on high-quality devices grown over patterned substrates, which is required for any cost saving to be beneficial. In this work, we demonstrate the growth of high-efficiency GaAs solar cells on GaAs substrates patterned with an array of nanoscale SiOX mask stripes. We show that reducing the pattern dimensions to submicron length scales with nanoimprint lithography enables defect-free coalescence. By varying the growth conditions, faceting of the epilayer material during overgrowth of the patterned mask was also controlled. A V/III ratio of 200 during MOVPE overgrowth produced smooth coalesced epilayers, which is desirable for the growth of subsequent device layers. Inverted GaAs front homojunction devices grown on patterned GaAs(001) substrates achieved threading dislocation densities below 5 × 10 5 cm –2 and maintained >23% solar cell efficiencies at one sun illumination, equivalent to control devices grown on unpatterned epi-ready substrates.
Surface Conversion of Single-Crystal Bi 2 Se 3 to β-In 2 Se 3
In this work, we demonstrate that the surface layers of single-crystal layered-2D Bi 2 Se 3 can be converted to layered-2D rhombohedral ß-In 2 Se 3 by annealing under a trimethylindium (TMIn) flux. Samples were prepared in a metalorganic chemical vapor deposition (MOCVD) chamber, then transferred under vacuum to a surface analysis chamber for analysis with low-energy electron diffraction (LEED) and Auger electron spectroscopy. Additional ex situ characterization included x-ray diffraction, transmission-electron microscopy (TEM), energy dispersive x-ray spectroscopy (EDS) elemental mapping, and Raman spectroscopy. The resulting single-crystal ß-In 2 Se 3 adopts the rhombohedral crystal structure (space group R-3m) and orientation of the underlying Bi 2 Se 3 , and the excess Bi atoms generated by this process create an underlying region of Bi-rich Bi x Se y . Due to the difference in bandgap between Bi 2 Se 3 and In 2 Se 3 , this conversion reaction presents a pathway to lateral heterojunctions if only selected regions are converted by masking the surface to spatially define the TMIn exposure. The conversion may also have implications for heteroepitaxy, because the in-plane lattice constants of Bi 2 Se 3 and In 2 Se 3 (0001) surfaces match those of InP and GaAs (111), respectively, and the natural cleavage planes of a layered-2D crystal facilitate substrate removal and reuse.
Understanding Improvements in Coalesced Epilayers Grown over Nanopatterned Substrates
Nanopatterned substrates provide opportunities for reducing costs of high-efficiency III-V devices through methods such as substrate reuse and growth on cheaper substrates. In this work, we aim to better understand some of the fundamental challenges of growing high quality III-V material on nanopatterned substrates. Through specific pattern orientations and control of overgrowth morphology, we report that smooth and defect-free coalesced III-V epilayers are attainable over nanopatterned GaAs substrates.
Towards a III-V Solar Cell with a Metamorphic Graded Buffer Directly Grown on V-Groove Si Substrates
V-groove Si substrates offer a promising route for the direct growth of III-V solar cells on low-cost, photovoltaic-grade Si. In this work, we develop a method for coalescing GaP nucleated on V-groove substrates into thin films suitable for the growth of III-V solar cells. We demonstrate the ability to suppress nucleation-related defects by modifying the V-groove substrate to cover the (0 0 1)-oriented Si V-groove tops with SiN x . A threading dislocation density (TDD) of 5 × 10 7 cm -2 was measured with electron channeling contrast imaging. Continuing work will focus on further reducing the TDD and the growth of a GaAs solar cell on a GaP on V-groove Si template.
Fabrication, Measurement, and Modeling of GaInP/GaAs Three-Terminal Cells and Strings
Three-terminal (3T) GaInP/GaAs solar cells are fabricated from inverted-grown monolithic tandems and processed with external metal contacts suitable for easy interconnection. Prototype 3T tandems both with and without tunnel junctions are demonstrated. They are characterized as a function of two independent variables in a variety of configurations, with each configuration holding one of the contacts common to two source-meter units (SMUs). Each of these different measurement configurations completely characterizes the device by transforming the results into 6 unique device parameters and plotting the total power parametrically in two dimensions. The performance is fit using a 3T optoelectronic model that includes luminescent coupling as well as important resistances. Eight of these devices are interconnected in various voltage-constrained configurations to form voltage-matched (VM) strings. Measurement and analysis of these III-V devices and strings are generally applicable to all 3T photovoltaics.
Compensated Contacts for Three-Terminal Transistor Solar Cells
The heterojunction bipolar transistor solar cell (HBTSC) is an alternative to conventional double-junction solar cells that combines the advantages of three-terminal architectures with a compact design. A critical part of the HBTSC fabrication is the implementation of the middle contact, the one associated to the base layer in the transistor structure, because this layer can be damaged by the diffusion of metallic species during contact annealing. As a solution we propose to implement a "compensated contact", that is, to leave a thin (< 200 nm) portion of emitter or collector between the base layer and the contact metals and compensate its doping during contact annealing. Using an Au/Zn/Au metal structure to compensate a 150 nm thick portion of the collector, we obtain a specific contact resistance ~8 10-4 ..omega.. cm2. This value is fairly invariant for annealing temperatures between 400 and 460 degrees C and annealing times between 2 and 5 minutes, and it does not improve by adding Pd to the metallic stack. Optimizing the compensated contact technology opens the path to the realization of III-V-material-based HBTSCs with open-circuit voltages and fill factors comparable to those of conventional multijunction architectures.
Homogenous Voltage-Matched Strings Using Three-Terminal Tandem Solar Cells: Fundamentals and End Losses
Strings constructed from three-terminal tandem (3TT) solar cells offer the performance benefits of voltage-matching (which reduces sensitivity to spectral variation), but without the subcell voltage isolation required by four-terminal cells. However, the circuitry for a 3TT string can become complex, making circuit analysis more challenging. Here, we illustrate the essential features of “homogenous” voltage-matched (VM) 3TT strings, for which all 3TT cells in the string are nominally identical (with the same design/doping sequence, such that they can be fabricated on the same manufacturing line). Several representative VM string configurations are explicitly considered, and used to describe the general construction of string I(V) curves. End losses intrinsic to these strings are discussed in detail, along with mitigation strategies to minimize their impact. Our analysis agrees with experimental results for eight-cell strings constructed from GaInP/GaAs 3TT devices.
Stringing Monolithic Three Terminal III-V Tandems
Tandemdevicesarewellknowntosurpasssinglejunctions.However,thelimitationsofcurrent-matchingisaconcern for changing spectra in terrestrial applications. Three terminal tandem (3T) devices can be more robust to these variations resulting in higher energy yield than single junction devices and two terminal series-connected tandems. We fabricate one-sun 3T tandem devices made of inverted grown III-V tandem (GaInP/t/GaAs) as a prototype of 3T tandems for stringing and measurement demon- strations. We demonstrate 3T tandem measurements that can be used to understand the use of 3T tandems in various constrained configurations. We have demonstrated the improvement of unconstrained 3T tandem cells over 2T series-connected cells as the illumination changes. We present initial results for micro-module with up to 8 3T tandem devices to be strung together.
Fundamentals of Three-Terminal Tandem Solar Cells: a Comprehensive Taxonomy
Three-terminal tandem (3TT) solar cells can overcome some of the limitations of two- and four-terminal tandem designs. However, the coupled nature of the cells adds a degree of complexity to the devices themselves and the ways that their performance can be measured and reported. To facilitate understanding, we have developed a taxonomy which encompasses all types of 3TT devices, enabling a common nomenclature for discussing devices and performance. Once the physical devices, contact nodes, and loading circuitry have been self-consistently described, it becomes apparent that a wide range of 3TT devices share a common set of design and operating principles.
Nucleation of High-Quality GaP on Si Through V-Groove Si Substrates
III-V growth on nanopatterned v-groove Si is a promising route to low cost Si-based tandem solar cells. Here, we study a high temperature MOVPE nucleation regime for growing GaP on v-groove Si. It is shown that MOVPE growth conditions can be used to control the facet selectivity of the GaP nucleation onto the v-grooves. The most promising nucleation condition was studied further, and it was demonstrated that it can be coalesced into a smooth thin film with promising material quality.