Engineering Papers⌕ Search

Engineering topics

Mazaris, G. A.

Publications and source records attributed to Mazaris, G. A..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Formation of a pn junction on an anisotropically etched GaAs surface using metalorganic chemical vapor deposition

A continuous p-type GaAs epilayer has been deposited on an n-type sawtooth GaAs surface using MOCVD. A wet chemical etching process was used to expose the intersecting (111)Ga and (-1 -1 1)Ga planes with 6-micron periodicity. Charge-collection microscopy was used to verify the presence of the pn junction thus formed and to measure its depth. The ultimate goal of this work is to fabricate a V-groove GaAs cell with improved absorptivity, high short-circuit current, and tolerance to particle radiation.

Leon, R. P.↗
NASA NTRS1984

Screen printed interdigitated back contact solar cell

Interdigitated back contact solar cells are made by screen printing dopant materials onto the back surface of a semiconductor substrate in a pair of interdigitated patterns. These dopant materials are then diffused into the substrate to form junctions having configurations corresponding to these patterns. Contacts having configurations which match the patterns are then applied over the junctions.

Baraona, C. R.↗
NASA NTRS1980

Open-circuit voltage improvements in low resistivity solar cells

Improvements in the open circuit voltage of 0.1 ohm-cm silicon solar cells were achieved using a multistep diffusion technique. Experimental details are given along with the results of an analysis that indicate that anomalous behavior of the electron mobility in the cell base limits attainment of higher voltages.

Godlewski, M. P.↗
NASA NTRS1980

Open-circuit voltage improvements in low resistivity solar cells

Improvements in the open-circuit voltage of 0.1 ohm-cm silicon solar cells have been achieved using a multistep diffusion technique. Experimental details are given along with the results of an analysis that indicate that anomalous behaviors of the electron mobility in the cell base limits attainment of higher voltages.

Godlewski, M. P.↗
NASA NTRS1979

Open-circuit voltage improvements in low-resistivity solar cells

Mechanisms limiting the open-circuit voltage in 0.1 ohm-cm solar cells were investigated. It was found that a rather complicated multistep diffusion process could produce cells with significantly improved voltages. The voltage capabilities of various laboratory cells were compared independent of their absorption and collection efficiencies. This was accomplished by comparing the cells on the basis of their saturation currents or, equivalently, comparing their voltage outputs at a constant current-density level. The results show that for both the Lewis diffused emitter cell and the Spire ion-implanted emitter cell the base component of the saturation current is voltage controlling. The evidence for the University of Florida cells, although not very conclusive, suggests emitter control of the voltage in this device. The data suggest further that the critical voltage-limiting parameter for the Lewis cell is the electron mobility in the cell base.

Godlewski, M. P.↗
NASA NTRS1978

Application of semiconductor diffusants to solar cells by screen printing

Diffusants were applied onto semiconductor solar cell substrates, using screen printing techniques. The method was applicable to square and rectangular cells and can be used to apply dopants of opposite types to the front and back of the substrate. Then, simultaneous diffusion of both dopants can be performed with a single furnace pass.

Evans, J. C., Jr.↗
NASA NTRS1974

The use of FEP Teflon in solar cell cover technology

FEP plastic film was used as a cover and as an adhesive to bond cover glasses to silicon solar cells. Various anti-reflective coatings were applied to cells and subsequently covered with FEP. Short-circuit currents were measured before and after application of the coating and of the FEP. FEP bonded to seven of the nine differently coated cells, with no change in the total short circuit current in four cases.

Broder, J. D.↗
NASA NTRS1973

The use of FEP Teflon in solar cell cover technology

FEP plastic film was used as a cover and as an adhesive to bond cover glasses to silicon solar cells. Various anti-reflective coatings were applied to cells and subsequently covered with FEP. Short circuit currents were measured before and after application of the coating and of the FEP. FEP was bonded to seven of the nine differently coated cells, with no change in the total short circuit current in four cases.

Broder, J. D.↗