Cavity Beam Position Monitor System for the Accelerator Test Facility 2
Abstract Not Provided
Engineering topics
Publications and source records attributed to May, J.
Abstract Not Provided
Abstract Not Provided
A substantial upgrade of the beam position monitors (BPM) at the ATF (Accelerator Test Facility) damping ring is currently in progress. Implementing digital read-out signal processing techniques in line with an optimized, low-noise analog downconverter, a resolution well below 1 mum could be demonstrated at 20 (of 96) upgraded BPM stations. The narrowband, high resolution BPM mode permits investigation of all types of non-linearities, imperfections and other obstacles in the machine which may limit the very low target aimed vertical beam emittance of < 2 pm. The technical status of the project, first beam measurements and an outlook to it's finalization are presented.
On August 8, 2005, the President signed the Energy Policy Act of 2005 (EPAct) into law. In Subtitle F of EPAct, Congress set forth various provisions that would change the way certain federal agencies (Agencies) coordinate to authorize the use of land for a variety of energy-related purposes. As part of Subtitle F of EPAct, Section 368 addresses the issue of energy transportation corridors on federal land for oil, gas, and hydrogen pipelines, as well as electricity transmission and distribution facilities. Because of the critical importance of improving the nation's electrical transmission grid, Congress recognized that electricity transmission issues should receive added attention when the Agencies address corridor location and analysis issues. In Section 368, Congress specifically directed the Agencies to consider the need for upgraded and new facilities to deliver electricity: In carrying out [Section 368], the Secretaries shall take into account the need for upgraded and new electricity transmission and distribution facilities to (1) improve reliability; (2) relieve congestion; and (3) enhance capability of the national grid to deliver electricity. Section 368 does not require the Agencies to consider or approve specific projects, applications for rights-of-way (ROWs), or other permits within designated energy corridors. Importantly, Section 368 does not direct, license, or otherwise permit any on-the-ground activity of any sort. If an applicant is interested in obtaining an authorization to develop a project within any corridor designated under Section 368, the applicant would have to apply for a ROW authorization and applicable permits. The Agencies would consider each application by applying appropriate project-specific reviews under requirements of laws and related regulations, including, but not limited to, the National Environmental Policy Act (NEPA), the Clean Water Act, the Clean Air Act, Section 7 of the Endangered Species Act (ESA), and Section 106 of the National Historic Preservation Act (NHPA). Under Section 368, Congress divided the United States into two groups of states: the 11 contiguous western states and the remaining states. Direction for energy transportation corridor analysis and selection in the 11 western states was addressed in Section 368(a) of EPAct, while direction for energy transportation corridor analysis and selection in all other states was addressed under Section 368(b) of EPAct. It was clearly the priority of Congress to conduct corridor location studies and designation first on federal lands in the western states. Under Section 368(a), the Agencies produced a programmatic environmental impact statement (EIS), Designation of Energy Corridors on Federal Land in the 11 Western States (DOE and DOI 2008), that was used in part as the basis for designating more than 6,000 mi (9,656 km) of energy transportation corridors on federal land in 11 western states. Under Section 368(a) of EPAct, Congress clearly stated the Agencies needed to (1) designate energy transportation corridors on federal land, (2) conduct the necessary environmental review of the designated corridors, and (3) incorporate the designated corridors into the appropriate land use plans. Congressional direction under Section 368(b) of EPAct differs from that provided under Section 368(a). Specifically, Section 368(b) requires the secretaries of the Agencies, in consultation with the Federal Energy Regulatory Commission (FERC), affected utility industries, and other interested persons, to jointly: (1) Identify corridors for oil, gas, and hydrogen pipelines and electricity transmission and distribution facilities on federal land in states other than the 11 western states identified under Section 368(a) of EPAct, and (2) Schedule prompt action to identify, designate, and incorporate the corridors into the applicable land use plans. While Section 368(a) clearly directs designation as a necessary first step for energy transportation corridors in the 11 western states, Section 368(b) directs the Agencies to first identify corridors and then schedule prompt action to identify, designate, and incorporate the corridors into applicable land use plans. To comply with the congressional direction provided in Section 368(b), the Agencies investigated corridor identification issues in the Section 368(b) states; this report to Congress provides information that could be relevant to possible future designation of energy corridors. Future designations, if appropriate and necessary, would occur when the Agencies undertake revisions and/or updates to land use plans that guide management decisions on lands located within individual administrative units, such as specific National Forests, National Parks, or Wildlife Refuges. At this time, the Agencies are not proposing any actions or decisions related directly or indirectly to designating energy corridors on federal land under Section 368(b) of EPAct.
The acceleration and heating of electrons by an intense laser normally incident on a steep overdense plasma interface is investigated using the particle-in-cell code osiris. Energetic electrons are generated by the laser's electric field in the vacuum region within {lambda}/4 of the surface. Only those electrons which originate within the plasma with a sufficiently large transverse momentum can escape the plasma. This mechanism relies on the standing wave structure created by the incoming and reflected wave and is therefore very different for linear and circularly polarized light.
We present molecular line observations, made with angular resolutions of {approx}20'', toward the filamentary infrared dark cloud G34.43+0.24 using the APEX [CO(3 {yields} 2), {sup 13}CO(3 {yields} 2), C{sup 18}O(3 {yields} 2), and CS(7 {yields} 6) transitions], Nobeyama 45 m [CS(2 {yields} 1), SiO(2 {yields} 1), C{sup 34}S(2 {yields} 1), HCO{sup +}(1 {yields} 0), H{sup 13}CO{sup +}(1 {yields} 0), and CH{sub 3}OH(2 {yields} 1) transitions], and SEST [CS(2 {yields} 1) and C{sup 18}O(2 {yields} 1) transitions] telescopes. We find that the spatial distribution of the molecular emission is similar to that of the dust continuum emission observed with 11'' resolution showing a filamentary structure and four cores. The cores have local thermodynamic equilibrium masses ranging from 3.3 x 10{sup 2} to 1.5 x 10{sup 3} M{sub sun} and virial masses from 1.1 x 10{sup 3} to 1.5 x 10{sup 3} M{sub sun}, molecular hydrogen densities between 1.8 x 10{sup 4} and 3.9 x 10{sup 5} cm{sup -3}, and column densities >2.0 x 10{sup 22} cm{sup -2}, values characteristic of massive star-forming cores. The {sup 13}CO(3 {yields} 2) profile observed toward the most massive core reveals a blue profile indicating that the core is undergoing large-scale inward motion with an average infall velocity of 1.3 km s{sup -1} and a mass infall rate of 1.8 x 10{sup -3} M{sub sun} yr{sup -1}. We report the discovery of a molecular outflow toward the northernmost core thought to be in a very early stage of evolution. We also detect the presence of high-velocity gas toward each of the other three cores, giving support to the hypothesis that the excess 4.5 {mu}m emission ('green fuzzies') detected toward these cores is due to shocked gas. The molecular outflows are massive and energetic, with masses ranging from 25 to 80 M{sub sun}, momentum 2.3-6.9 x 10{sup 2} M{sub sun} km s{sup -1}, and kinetic energies 1.1-3.6 x 10{sup 3} M{sub sun} km{sup 2} s{sup -2}, indicating that they are driven by luminous, high-mass young stellar objects.
The coupling efficiency between the ignition laser and the target core for the fast ignition concept is studied using two-dimensional particle-in-cell simulations. The details of the energy transport within the weakly collisional overdense plasma of a fast ignition target are examined by performing a series of particle-in-cell simulations, where the intensity incident on a 100 times critical plasma with 50 {mu}m radius is varied between each simulation. The simulations show that the peak energy flux of the ignition electrons is significantly lowered as the electrons traverse the collisionless plasma from the critical density through a weakly collisional overdense plasma region. This allows higher intensity lasers to be used thereby improving the coupling efficiency. In addition, we find that a higher percentage of the ignition laser energy is delivered to the core of the simulation target at higher intensity. The coupling efficiency increases in time during the simulations which are run for 2.5 ps. For a laser intensity of 8x10{sup 20} W/cm{sup 2} the simulations indicate that more than 15% of the incident laser energy is eventually absorbed in a dense plasma core.
Script-based I/O benchmarks record the I/O behavior of applications by using an instrumentation library to trace I/O events and their timing. A replay engine can then reproduce these events from the script in the absence of the original application. This type of benchmark reproduces real-world I/O workloads without the need to distribute, build, or run complex applications. However, faithfully recreating the I/O behavior of the original application requires careful design in both the instrumentation library and the replay engine. This paper presents the Pianola script-based benchmarking system, which includes an accurate and unobtrusive instrumentation system and a simple-to-use replay engine, along with some additional utility programs to manage the creation and replay of scripts. We show that for some sample applications, Pianola reproduces the qualitative features of the I/O behavior. Moreover, the overall replay time and the cumulative read and write times are usually within 10% of the values measured for the original applications.
A beam position monitor (BPM) upgrade at the KEK Accelerator Test Facility (ATF) damping ring has been accomplished in its first stage, carried out by a KEK/FNAL/SLAC collaboration under the umbrella of the global ILC R&D effort. The upgrade consists of a high resolution, high reproducibility read-out system, based on analog and digital downconversion techniques, digital signal processing, and also tests a new automatic gain error correction schema. The technical concept and realization, as well as preliminary results of beam studies are presented.
Dipole modes have been shown to be successful diagnostics for the beam position in superconducting accelerating cavities at the Free Electron Laser in Hamburg (FLASH) facility at DESY. By help of downmixing electronics the signals from the two higher order mode (HOM) couplers mounted on each cavity are monitored. The calibration, based on singular value decomposition, is more complicated than in standard position monitors. Position like signals based on this calibration are currently being in the process of being included in the control system. A second setup based on digitizing the spectrum from the HOM couplers has been used for monitoring monopole modes. The beam phase with respect to the RF has been thus monitored. The position calibration measurements and phase monitoring made at the FLASH are presented.
The Petascale Simulation Initiative LDRD project began in May 2004 and ended in April 2007. The overall goal of the project was to develop a computational model that would help LLNL simulation codes use petaflop-scale computers effectively, with specific emphasis on multiscale simulation. An early deliverable of the project was a report that surveyed a range of LLNL simulation codes so that the project would better understand their structure and needs. This report was titled 'Survey of Selected LLNL Unclassified Parallel Simulation Codes', UCRL-TR-207192. Based on the findings of this report, the project proceeded along two complementary paths. One goal was to develop a technique to reduce the amount of redundant calculation in a multiscale simulation by caching certain fine-scale simulation results as they were generated and then interpolating new values, where appropriate, based on cached data. This technique, which we call 'Adaptive Sampling', was successfully applied in a materials modeling simulation, and the results are detailed in a journal paper entitled 'Embedded polycrystal plasticity and adaptive sampling', UCRL-JRNL-226715. In this paper we showed an example multiscale simulation in which we were able to achieve a 40x speedup over the standard technique for doing the same problem and with very little loss of accuracy. A second paper that further describes adaptive sampling was recently accepted as a journal publication: 'Adaptive sampling in hierarchical simulation', UCRL-JRNL-232594. The second thrust of the project was to develop a parallel programming model that supports dynamic creation and coordination of sequential and parallel subcomputations to form larger 'federated' simulations. We call this model 'Cooperative Parallelism'. The model is described in 'Overview of the Cooperative Parallel programming model', UCRL-CONF-230029, which was submitted to Supercomputing 2007 (but not accepted for publication). We will be revising the paper and submitting it for publication again. In the mean time the model is under study for use in both AX division and B division, and possibly other programs as well. Finally, a higher-level view of our work appears in book chapter entitled 'Multiscale simulation and petascale computing', UCRL-BOOK-227348, in 'Petascale Computing: Algorithms and Applications'. The description in this chapter sets our work in the larger context of petascale simulation.
Critical data science applications requiring frequent access to storage perform poorly on today's computing architectures. This project addresses efficient computation of data-intensive problems in national security and basic science by exploring, advancing, and applying a new form of computing called storage-intensive supercomputing (SISC). Our goal is to enable applications that simply cannot run on current systems, and, for a broad range of data-intensive problems, to deliver an order of magnitude improvement in price/performance over today's data-intensive architectures. This technical report documents much of the work done under LDRD 07-ERD-063 Storage Intensive Supercomputing during the period 05/07-09/07. The following chapters describe: (1) a new file I/O monitoring tool iotrace developed to capture the dynamic I/O profiles of Linux processes; (2) an out-of-core graph benchmark for level-set expansion of scale-free graphs; (3) an entity extraction benchmark consisting of a pipeline of eight components; and (4) an image resampling benchmark drawn from the SWarp program in the LSST data processing pipeline. The performance of the graph and entity extraction benchmarks was measured in three different scenarios: data sets residing on the NFS file server and accessed over the network; data sets stored on local disk; and data sets stored on the Fusion I/O parallel NAND Flash array. The image resampling benchmark compared performance of software-only to GPU-accelerated. In addition to the work reported here, an additional text processing application was developed that used an FPGA to accelerate n-gram profiling for language classification. The n-gram application will be presented at SC07 at the High Performance Reconfigurable Computing Technologies and Applications Workshop. The graph and entity extraction benchmarks were run on a Supermicro server housing the NAND Flash 40GB parallel disk array, the Fusion-io. The Fusion system specs are as follows: SuperMicro X7DBE Xeon Dual Socket Blackford Server Motherboard; 2 Intel Xeon Dual-Core 2.66 GHz processors; 1 GB DDR2 PC2-5300 RAM (2 x 512); 80GB Hard Drive (Seagate SATA II Barracuda). The Fusion board is presently capable of 4X in a PCIe slot. The image resampling benchmark was run on a dual Xeon workstation with NVIDIA graphics card (see Chapter 5 for full specification). An XtremeData Opteron+FPGA was used for the language classification application. We observed that these benchmarks are not uniformly I/O intensive. The only benchmark that showed greater that 50% of the time in I/O was the graph algorithm when it accessed data files over NFS. When local disk was used, the graph benchmark spent at most 40% of its time in I/O. The other benchmarks were CPU dominated. The image resampling benchmark and language classification showed order of magnitude speedup over software by using co-processor technology to offload the CPU-intensive kernels. Our experiments to date suggest that emerging hardware technologies offer significant benefit to boosting the performance of data-intensive algorithms. Using GPU and FPGA co-processors, we were able to improve performance by more than an order of magnitude on the benchmark algorithms, eliminating the processor bottleneck of CPU-bound tasks. Experiments with a prototype solid state nonvolative memory available today show 10X better throughput on random reads than disk, with a 2X speedup on a graph processing benchmark when compared to the use of local SATA disk.