Engineering Papers⌕ Search

Engineering topics

Marion, B

Publications and source records attributed to Marion, B.

Influence of Atmospheric Variations on Photovoltaic Performance and Modeling Their Effects for Days with Clear Skies: Preprint

Although variation in photovoltaic (PV) performance is predominantly influenced by clouds, performance variations also exist for days with clear skies with different amounts of atmospheric constituents that absorb and reflect different amounts of radiation as it passes through the earth's atmosphere. The extent of the attenuation is determined by the mass of air and the amounts of water vapor,aerosols, and ozone that constitute the atmosphere for a particular day and location. Because these constituents selectively absorb radiation of particular wavelengths, their impact on PV performance is sensitive to the spectral response of the PV device. The impact may be assessed by calculating the spectral mismatch correction. This approach was validated using PV module performance data atthe National Renewable Energy Laboratory (NREL) for summer, fall, and winter days with clear skies. The standard deviation of daily efficiencies for single-crystal Si, a-Si/a-Si/a-Si:Ge, CdTe, and CIGS PV modules were reduced to 0.4% to 1.0% (relative) by correcting for spectral mismatch, temperature, and angle-of-incidence effects.

14 SOLAR ENERGY↗

Determining Outdoor CPV Cell Temperature: Preprint

An accurate method is needed for determining cell temperature when measuring CPV modules outdoors. It has been suggested that cell temperature can be calculated though a procedure that shutters sunlight to the cells while measuring the transients in open-circuit voltage (Voc) and heat sink temperature. This paper documents application of this shutter procedure to multiple CPV modules at NREL. Thechallenges and limitations are presented along with an alternate approach to measuring CPV cell operating temperature.

14 SOLAR ENERGY↗

Minimizing Variation in Outdoor CPV Power Ratings: Preprint

The CPV community has agreed to have both indoor and outdoor power ratings at the module level. The indoor rating provides a repeatable measure of module performance as it leaves the factory line while the outdoor rating provides a measure of true performance under real world conditions. The challenge with an outdoor rating is that the spectrum, temperature, wind speed, etc are constantly in fluxand therefore the resulting power rating varies from day to day and month to month. This work examines different methodologies for determining the outdoor power rating with the goal of minimizing variation even if data are collected under changing meteorological conditions.

14 SOLAR ENERGY↗

Investigation into Spectral Parameters as they Impact CPV Module Performance

The CPV industry is well aware that performance of triple junction cells depends on spectral conditions but there is a lack of data quantifying this spectral dependence at the module level. This paper explores the impact of precipitable water vapor, aerosol optical depth (AOD), and optical air mass on multiple CPV module technologies on-sun in Golden, CO.

14 SOLAR ENERGY↗

Considerations for How to Rate CPV

The concentrator photovoltaic (CPV) industry is introducing multiple products into the marketplace, but, as yet, the; community has not embraced a unified method for assessing a nameplate rating. The choices of whether to use 850,; 900, or 1000 W/m2 for the direct-normal irradiance and whether to link the rating to ambient or cell temperature will; affect how CPV modules are rated and compared with other technologies. This paper explores the qualitative and; quantitative ramifications of these choices using data from two multi-junction CPV modules and two flat-plate; modules.

14 SOLAR ENERGY↗

Opportunities and Challenges for Power Electronics in PV Modules (Presentation)

The presentation describes the value of adding DC converters and other power electronics to modules to improve their output even when shading or bad cells would otherwise decrease the module output. The presentation was part of a workshop sponsored by ARPA-E exploring the opportunities for power electronics to support PV applications.

14 SOLAR ENERGY↗

Performance and Economic Analysis of Distributed Power Electronics in Photovoltaic Systems

Distributed electronics like micro-inverters and DC-DC converters can help recover mismatch and shading losses in photovoltaic (PV) systems. Under partially shaded conditions, the use of distributed electronics can recover between 15-40% of annual performance loss or more, depending on the system configuration and type of device used. Additional value-added features may also increase the benefitof using per-panel distributed electronics, including increased safety, reduced system design constraints and added monitoring and diagnostics. The economics of these devices will also become more favorable as production volume increases, and integration within the solar panel?s junction box reduces part count and installation time. Some potential liabilities of per-panel devices includeincreased PV system cost, additional points of failure, and an insertion loss that may or may not offset performance gains under particular mismatch conditions.

14 SOLAR ENERGY↗

Improved test method to verify the power rating of a photovoltaic (PV) project.

This paper reviews the PVUSA power rating method and presents two additional methods that seek to improve this method in terms of model precision and increased seasonal applicability. It presents the results of an evaluation of each method based upon regression analysis of over 12 MW of operating photovoltaic (PV) systems located in a wide variety of climates. These systems include a variety of PV technologies, mounting configurations, and array sizes to ensure the conclusions are applicable to a wide range of PV designs and technologies. The work presented in this paper will be submitted to ASTM for use in the development of a standard test method for certifying the power rating of PV projects.

14 SOLAR ENERGY↗

Instrumentation for Evaluating PV System Performance Losses from Snow

When designing a photovoltaic (PV) system for northern climates, the prospective installation should be evaluated with respect to the potentially detrimental effects of snow preventing solar radiation from reaching the PV cells. The extent to which snow impacts performance is difficult to determine because snow events also increase the uncertainty of the solar radiation measurement, and the presence of snow needs to be distinguished from other events that can affect performance. This paper describes two instruments useful for evaluating PV system performance losses from the presence of snow: (1) a pyranometer with a heater to prevent buildup of ice and snow, and (2) a digital camera for remote retrieval of images to determine the presence of snow on the PV array.

14 SOLAR ENERGY↗

Comparison of Predictive Models for Photovoltaic Module Performance: Preprint

This paper examines three models used to estimate the performance of photovoltaic (PV) modules when the irradiances and PV cell temperatures are known. The results presented here were obtained by comparing modeled and measured maximum power (Pm) for PV modules that rely on different technologies.

14 SOLAR ENERGY↗

Comparison of Predictive Models for PV Module Performance (Presentation)

This paper examines three models used to estimate the maximum power (P{sub m}) of PV modules when the irradiance and PV cell temperature are known: (1) the power temperature coefficient model, (2) the PVFORM model, and (3) the bilinear interpolation model. A variation of the power temperature coefficient model is also presented that improved model accuracy. For modeling values of P{sub m}, an 'effective' plane-of-array (POA) irradiance (E{sub e}) and the PV cell temperature (T) are used as model inputs. Using E{sub e} essentially removes the effects of variations in solar spectrum and reflectance losses, and permits the influence of irradiance and temperature on model performance for P{sub m} to be more easily studied. Eq. 1 is used to determine E{sub e} from T and the PV module's measured short-circuit current (I{sub sc}). Zero subscripts denote performance at Standard Reporting Conditions (SRC).

14 SOLAR ENERGY↗

Session: Test and Evaluation (Presentation)

The overall goal of this presentation is: (1) provide test and evaluation of PV cells/modules/systems to TPP participants, other PV industry, labs, and universities in support of technology optimization efforts sponsored by DOE's Solar Program and the SAI; (2) support commercial and emerging technology development; (3) provide component and system performance data to improve and validate system performance models; (4) provide T and E support for reliability activities; and (5) priority is placed on TPP's and other solicitations.

14 SOLAR ENERGY↗