Engineering Papers⌕ Search

Engineering topics

Malmali, Mahdi

Publications and source records attributed to Malmali, Mahdi.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Comparative Energetics of Various Membrane Distillation Configurations and Guidelines for Design and Operation

This paper presents a comparative performance study of single-stage desalination processes with major configurations of membrane distillation (MD) modules. MD modules covered in this study are (a) direct contact MD (DCMD), (b) vacuum MD (VMD), (c) sweeping gas MD (SGMD), and (d) air gap MD (AGMD). MD-based desalination processes are simulated with rigorous theoretical MD models supported by molecular thermodynamic property models for the accurate calculation of performance metrics. The performance metrics considered in MD systems are permeate flux and energy efficiency, i.e., gained output ratio (GOR). A general criterion is established to determine the critical length of these four MDs (at fixed width) for the feasible operation of desalination in a wide range of feed salinities. The length of DCMD and VMD is restricted by the feed salinity and permeate flux, respectively, while relatively large AGMD and SGMD are allowed. The sensitivity of GOR flux with respect to permeate conditions is investigated for different MD configurations. AGMD outperforms other configurations in terms of energy efficiency, while VMD reveals the highest permeate production. With larger MD modules, utilization of thermal energy supplied by the hot feed for evaporation is in the order of VMD > AGMD > SGMD > DCMD. Simulation results highlight that energy efficiency of the overall desalination process relies on the efficient recovery of spent for evaporation, suggesting potential improvement in energy efficiency for VMD-based desalination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Combined chlorine dioxide–membrane distillation for the treatment of produced water

Membrane distillation (MD) is a promising technique for desalinating hypersaline brine, such as produced water (PW). To date, fouling and scaling have remained as major challenges for MD implementation. In this study, chlorine dioxide combined with induced air floatation (ClO 2 -IAF) was systematically investigated as a pretreatment prior to MD. First, the ClO 2 generation based on sodium chlorite and hydrochloric acid was optimized to maximize the on-demand ClO 2 production. The maximum production yield of 18.4% was obtained with 4wt.% NaClO 2 and 20wt.% HCl solutions, with a molar ratio of 1:1.25. Then, two real PW samples were pretreated, and removal efficiencies for total suspended solids (TSS), turbidity, iron, and total organic carbon (TOC) were comprehensively studied by varying the ClO 2 dosage between 6 and 91 mg/L. The ClO 2 -IAF pretreatment displayed TSS and turbidity removals above 90% and TOC removal close to 55%. Further, the PW constituents such as benzene, toluene, ethylbenzene, xylene (BTEX), and total petroleum hydrocarbons (TPH) were analyzed and quantified throughout the cascade of the treatments. The volatiles like BTEX were mainly removed by air floatation, while saturated hydrocarbons such as TPH were retained by the hydrophobic membrane. The MD long-term stability without any in-place cleaning was evaluated, and the membrane withstood for twenty two days without wetting, suggesting that optimizing oxidation pretreatment is critical for mitigating the fouling in MD. Results suggest that organic fouling in PW could be effectively reduced by the pretreatment, but further treatment is required to mitigate the scaling, which resulted in MD wetting.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Energy and exergy analysis of multi-stage vacuum membrane distillation integrated with mechanical vapor compression

Membrane distillation (MD) is a promising candidate for desalinating hypersaline brine, but its poor energy efficiency has remained a major barrier for widespread application. One possible solution to this issue is to recover the latent heat in the process. In this work, a multi-stage vacuum MD (MSVMD) was integrated with a mechanical vapor compressor (MVC) to enhance the latent heat recovery, and the energetic and exergetic performance of this integrated process was examined. A comprehensive energy and exergy analysis is provided to compare MSVMD and MSVMD-MVC processes for desalination of hypersaline brine. This analysis was conducted by examining the effect of the compression ratio on the energetic and exergetic performance, and the findings are reported in terms of specific thermal energy consumption (STEC), specific electricity consumption (SEC), and exergetic efficiency. The energy analysis shows that thermal energy consumption can be reduced as the compression ratio increases, due to the enhancement of latent heat recovery. The MSVMD-MVC process can be operated in a steady-state condition, without the need for thermal heat input; with STEC and SEC of 0 and 49 kWh/m 3 at the feed temperature of 50 °C and MVC compression ratio of 2.14. Moreover, exergy analysis demonstrates the efficacy of the eNRTL model in exergy calculation. Exergy destruction can be greatly reduced by increasing the compression ratio to an optimal value. For high salinity brine (124 g/L), MSVMD-MVC achieved a higher exergetic efficiency of 6.85%, compared to 2.42% in MSVMD. Furthermore, the result suggests that the application of MVC can intensify the energy efficiency and exergetic efficiency of the MSVMD system, although this process cannot outperform the current desalination technologies from the standard primary energy point of view.

42 ENGINEERING↗
DOE OSTI2022

Continuous electrocoagulation-membrane distillation unit for treating hydraulic fracturing produced water

Hydraulic fracturing oil and gas produced water is frequently highly impaired. While it is often deep well injected, there is great interest in treating this water for beneficial uses. Given the complexity of these produced waters, multiple unit operations are necessary. Electrocoagulation has been considered as a promising pretreatment technology. Here electrocoagulation is considered as a pretreatment prior to membrane distillation. The focus of this work is on understanding the electrocoagulation process in order to design an integrated unit operation. Electrocoagulation is used to remove organic compounds that will foul the membrane leading to membrane failure during membrane distillation. Using aluminum or iron electrodes, half-cell reactions in the electrocoagulation cell and electrode potentials have been calculated. Electrocoagulation was conducted using a continuous electrocoagulation reactor with actual produced water using aluminum, iron or mixed aluminum and iron electrodes. Here, the results obtained here indicate that electrocoagulation can obtain good removal efficiency of total organic carbon (TOC) by using different reaction conditions. Removal of organic compounds is essential to minimize fouling during membrane distillation. Further the performance of the electrocoagulation process depends strongly on the quality of the feed water. Insoluble species were more effectively coagulated than dissolved organic species. Continuous electrocoagulation shows great potential as a scalable unit operation for pretreating hydraulic fracturing produced water.

42 ENGINEERING↗
DOE OSTI2022

Analysis of fouling mechanism in ultrafiltration of produced water

Flux decline measurements provided insight into the fouling behavior of ultrafiltration (UF) membranes for produced water (PW) treatment. Three UF membranes were compared in terms of the rate and the intensity of fouling. The flux decline analysis showed the fouling transition from blocking mechanisms (i.e., complete and intermediate blocking as well as standard blocking) to cake formation occurs earlier for more permeable membranes. Lower trans-membrane pressure (TMP) of 0.1 bar led to particle accumulation on the membrane surface leading to cake formation as the predominant fouling mechanism. In higher TMP experiments, standard and intermediate blocking followed by cake formation were found to be apparent fouling mechanisms. Overall, for the membranes with higher permeabilities and for the filtrations with pre-filtered feed, faster transition to cake formation was observed primarily due to crowd out effect. By understanding membrane fouling and behavior, it is possible to mitigate performance losses in membrane-based technologies that could be used for the treatment of PW. Furthermore, this study provides information to identify blocking rate and intensity in various conditions for UF membranes when treating PW.

42 ENGINEERING↗
DOE OSTI2021

Molecular thermodynamics for scaling prediction: Case of membrane distillation

Membrane distillation (MD) for water treatment is significantly impaired by the scaling of dissolved minerals. The type and content of minerals generally measured as total dissolved solids (TDS) in hypersaline brines not only reduce the MD flux but also control the scaling behavior on the membrane surface. The scaling-induced pore blockage further reduces water flux and eventually leads to membrane wetting. The scaling problem is even more pronounced in the treatment of produced water (PW) as it contains 3–7 times higher TDS concentrations, compared to seawater. Theoretically, the necessary conditions for a salt to precipitate can be traced from its solubility product constant and activity of the constituents within the solution. Therefore, a comprehensive thermodynamic model is necessary to represent the electrolyte behavior and to predict the precipitation of different salts in a complex solution like PW. We pursued electrolyte Nonrandom Two Liquid Theory (eNRTL), a state-of-the-art electrolyte model, to address the PW fluid phase equilibria. With a fully parameterized eNRTL model, we predicted salt precipitations in two different PW samples and compared the results against the experimental findings. Furthermore, here we forecast the precipitation of salts in response to the change in PW concentration and temperature in the MD operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Comparative analysis of various pretreatments to mitigate fouling and scaling in membrane distillation

Membrane distillation (MD) has shown strong promise for treating hypersaline produced water (PW) streams. Scaling and fouling on the membrane surface, however, have been identified as major challenges for commercialization and widespread application. The focus of this study was to first identify the nature of foulants and scalants on the membrane surface and then investigate the pretreatment strategies that mitigate the extent of fouling and scaling on the membrane surface. Vacuum MD (VMD) was selected for this study because of its higher flux at more moderate feed temperatures that eventually leads better assessment of fouling and scaling on the membrane surface. VMD flux tests were carried out with three different real PW samples at total dissolved solids concentrations in the range of 120-160 g/L. It was found that an efficient pretreatment prior to MD is required to mitigate the fouling potential of the organic matter, mostly suspended constituents, in PW samples. Suspended organics fouled and quickly wetted the MD membrane. Major conventional treatments, including filtration, oxidation, coagulation, air floatation, and aeration were investigated to pretreat the PW before VMD tests. A comprehensive comparative analysis is presented showing that the ultrafiltration and coagulation pretreatments displayed the best performance in mitigating the fouling and scaling, while oxidative pretreatment was found to be effective in reducing the iron concentration to less than 5 ppm. The surface of scaled membranes was carefully characterized to further evaluate the performance of each pretreatment. The components that had the highest tendency to precipitate on the membrane surface were identified as strontium sulfate, calcium carbonate, sodium chloride, iron oxide, and silica. In closing, these findings are supported by thermodynamic estimation of the saturation index.

42 ENGINEERING↗
DOE OSTI2020

Combined electrocoagulation-microfiltration-membrane distillation for treatment of hydraulic fracturing produced water

Hydraulic fracturing flowback and produced water is a highly impaired wastewater containing dissolved salts polar and non-polar organic compounds, oil and surfactants. Here a combined electrocoagulation - microfiltration – membrane distillation process has been used to treat this wastewater. Electrocoagulation followed by microfiltration was used to pretreat the wastewater prior membrane distillation. The initial total dissolved solids (TDS) concentration was extremely high being 245,300 mg L -1 . After electrocoagulation, the total organic carbon (TOC) was reduced from 120 mg L -1 to 64 mg L -1 . Tangential flow microfiltration using a 0.1 μm pore size polyethersulfone membrane was used to separate the particulate matter after electrocoagulation and to further reduce the TOC to 44 mg L -1 . Membrane distillation was used to desalinate the pretreated produced water resulting in a high quality treated water (TDS of 56 mg L -1 and TOC 1 mg L -1 ). Three membranes with very different surface morphology were used: commercially available polyvinylidene fluoride, electrospun poly(vinylidene fluoride-co-hexafluoropropylene) nanofibers and multiwalled carbon nanotube coated polytetrafluoroethylene. The TDS in the retentate increased to over 350,000 mg L -1 . During membrane distillation, the temperature of the feed tank was maintained at 36 °C while the feed entered the module at 60 °C in order to minimize scaling on the membrane. The surface properties of an ideal membrane that is resistant to wetting and provides high flux is likely to depend on the TDS and properties of the wastewater.

42 ENGINEERING↗