Engineering topics

Malcolm, Gerald N.

Publications and source records attributed to Malcolm, Gerald N..

26 records · Page 2

NASA NTRS1991

Aerodynamic control using forebody blowing and suction

Aerodynamic control using pneumatic forebody flow control was studied. Three methods of control were investigated: (1) blowing from a localized jet, (2) blowing from a slot, and (3) surface suction. Flow visualization and yawing moment measurements were performed on F/A-18 models in a water tunnel. The results show that all the methods were effective in controlling the forebody flow over a wide range of angles of attack and sideslip. The advantages and limitations of each of the control methods were discussed. The experiments suggested that all the control methods work basically on the principle of separation control. Based on the results of the water tunnel tests, the blowing or suction mass flow requirements appear to be within the limits of typical engine-bleed available from a modern fighter engine.

Ng, T. Terry↗

NASA NTRS1990

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Methods of manipulating the forebody vortices on a generic fighter model to produce controlled yawing moments at high angles of attack were investigated. Forces and moments were measured on the complete configuration and on the isolated forebody. Two schemes for vortex control on the forebody were evaluated: individually-controlled tip strakes and individually-controlled blowing ports. The effectiveness of the forebody strakes in controlling forebody side forces was strongly dependent on the size and location of the strakes. A yawing moment can be produced by deploying the forebody strakes asymmetrically, or can be eliminated by deploying the strakes symmetrically. The most effective strake position was found to be near the primary separation point, between 105 and 120 deg from windward. Blowing on the surface of the model was also shown to have a strong effect on the yawing moment. Blowing either forward or aft tangential to the surface appears to be more effective than blowing normal to the surface. The most effective method to control the yawing moment on the forebody was to minimize the natural asymmetry with a pair of small symmetrically mounted tip strakes and to perturb the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗

NASA NTRS1990

Effect of leading edge roundness on a delta wing in wing-rock motion

The effect of wing leading-edge roundness on wing rock was investigated using flow visualization in a water tunnel. Eighty degree delta wing models were tested on free-to-roll and forced oscillation rigs. The onset of wing rock was delayed by increasing the roundness of the leading edges. The wing rock amplitude and frequency results suggested that damping was increased at lower angles of attack but reduced at higher angles of attack. Vortex lift-off and vortex breakdown, especially during dynamic situations, were strongly affected by the leading edge roundness. Different forms of wing rock motion could be sustained by combinations of vortex breakdown and vortex lift-off. Behaviors of the wing and vortex motions were explained by the influence of leading edge roundness on the separation location, vortex trajectory, and vortex breakdown.

Ng, T. Terry↗

NASA NTRS1989

Flow visualization study of delta wings in wing-rock motion

Water tunnel flow visualizations have been conducted for the wing-rock phenomenon in the cases of models having different leading-edge sweeps and roundness. Wing rock, which is noted to occur in the absence of asymmetric vortex liftoff, vortex breakdown, and static hysteresis, is seen to be initiated by flowfield asymmetries that are induced by flow disturbances and vortex interactions near the apex region; one vortex is thereby strengthened while the other is weakened, inducing a roll moment. Leading-edge roundness decreases vortex strength and reduces vortex spacing, reducing the tendency to wind rock and coupled vortex motions at higher angles-of-attack.

Ng, T. Terry↗

NASA NTRS1989

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Low-speed wind tunnel experiments have been conducted to define methods for the manipulation of a generic fighter forebody's vortices in order to generate controlled yawing moments at high alpha. Attention is given to two vortex-control schemes: one involving independently controlled forebody tip strakes, and the other individually controlled blowing ports on the forebody. The most effective methods for forebody yawing-moment control were found to be the minimization of natural asymmetry with a pair of symmetrically mounted tip strakes, and the perturbation of the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗

NASA NTRS1987

Water facilities in retrospect and prospect: An illuminating tool for vehicle design

Water facilities play a fundamental role in the design of air, ground, and marine vehicles by providing a qualitative, and sometimes quantitative, description of complex flow phenomena. Water tunnels, channels, and tow tanks used as flow-diagnostic tools have experienced a renaissance in recent years in response to the increased complexity of designs suitable for advanced technology vehicles. These vehicles are frequently characterized by large regions of steady and unsteady 3-D flow separation and ensuing vortical flows. The visualization and interpretation of the complicated fluid motions about isolated vehicle components and complete configurations in a time and cost effective manner in hydrodynamic test facilities is a key element in the development of flow control concepts, and, hence, improved vehicle designs. A historical perspective of the role of water facilities in the vehicle design process is presented. The application of water facilities to specific aerodynamic and hydrodynamic flow problems is discussed, and the strengths and limitations of these important experimental tools are emphasized.

Erickson, Gary E.↗

NASA NTRS1986

An experimental investigation of the aerodynamics of a NACA 64A010 airfoil-flap combination with and without flap oscillations. Part 1: Steady-state characteristics

A NACA 64A010 airfoil with a sealed-gap 1/4-chord flap was tested between splitter plates in the NASA Ames 11- by 11-Foot Transonic Wind Tunnel at Mach numbers from 0.50 to 0.85, and Reynolds numbers based on chord from 3 to 13 million. Although the main purpose of the test was to obtain unsteady pressure data with the flap oscillating, no unsteady data are presented in this paper. The steady-state data are presented and compared with other test data to provide a basis for evaluating the results. Pressure data at two span stations are used to deduce early boundary-layer transitions at the midspan at higher Mach numbers, angles of attack, and flap angles. The effects of flap angle on pressures, normal force, pitching moment, and hinge moment are also presented in the report. Mach number errors caused by the splitter-plate configuration and the angle of attack are evaluated using pressure measurements near the floor and ceiling of the wind tunnel.

Buell, Donald A.↗

NASA NTRS1980

Transonic Shock-Wave/Boundary-Layer Interactions on an Oscillating Airfoil

Unsteady aerodynamic loads were measured on an oscillating NACA 64A010 airfoil In the NASA Ames 11 by 11 ft Transonic Wind Tunnel. Data are presented to show the effect of the unsteady shock-wave/boundary-layer interaction on the fundamental frequency lift, moment, and pressure distributions. The data show that weak shock waves induce an unsteady pressure distribution that can be predicted quite well, while stronger shock waves cause complex frequency-dependent distributions due to flow separation. An experimental test of the principles of linearity and superposition showed that they hold for weak shock waves while flows with stronger shock waves cannot be superimposed.

Davis, Sanford S.↗