Engineering Papers⌕ Search

Engineering topics

Majumdar, S.

Publications and source records attributed to Majumdar, S..

At least 19 records

Predicting Rupture Pressure and Leak Rate of Alloy 600 U-bend Tubes with PWSCC and Comparing with Test Results (Technical Letter Report)

This report summarizes structural integrity work performed for the US NRC that predicts the structural integrity of steam generator (SG) tubes with flaws in the U-bend. The work covers model development and validation for U-bend tubes containing lab-induced primary water stress corrosion cracks (PWSCC). Limit load models for plastic collapse predicting ligament rupture pressure and leak rate of cracked U-bend tubes were developed and validated with pressure tests and finite element analyses (FEAs). Failure pressure and leak rate tests were conducted at room temperature on Alloy 600 U-bend tubes containing flaws located at various locations around the U-bend. Existing models for predicting structural integrity of straight tubes with well defined, rectangular, electro-discharge-machined (EDM) flaws were modified and used to predict the ligament rupture and unstable burst pressures as well as leak rates for the PWSCC flaws in the U-bend section.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Predicting Rupture Pressure and Leak Rate of Alloy 600 Tubes with ODSCC and Comparing with Test Results (Technical Letter Report)

This report summarizes structural integrity work performed for the U.S. NRC that predicts the rupture pressure and leak rate of flawed steam generator (SG) tubes. The work includes pressure testing of straight tubes with lab-induced outer diameter stress corrosion cracks (ODSCC). Existing models for predicting rupture pressure and leak rate of straight tubes with well-defined, rectangular, electro-discharge-machined (EDM) flaws were modified and used to predict the measured rupture pressures and leak rates from straight tubes with ODSCC. Models previously developed for EDM notches in straight tubes were modified for ODSCC by using the equivalent rectangular crack (ERC) method.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Densification, Microstructural Evolution, Mechanical Properties and Oxidation Study of CrB{sub 2} + EuB{sub 6} Composite

This paper reports the results of investigation on densification, microstructural evolution, mechanical properties and oxidation study of CrB{sub 2} + EuB{sub 6} composite. CrB{sub 2} + EuB{sub 6} (10 and 20 wt.%) composites have been fabricated by hot pressing at a temperature of 1700 °C and 35 MPa pressure. The hardness and flexural strength were measured in the range of 21.25-24.48 GPa and 171-199 MPa, respectively. The fracture toughness increased from 3.3 to 4.01 MPa m{sup 1/2} by the addition of 20% EuB{sub 6}. Microstructural evolution revealed the uniform distribution of EuB{sub 6} and absence of any reaction product. Fracture surface analysis confirmed the presence of transgranular mode of fracture. Oxidation study at 1200 °C revealed that the developed composites have good oxidation resistance and followed the parabolic rate of oxidation.

36 MATERIALS SCIENCE↗

Assessment of First Wall and Blanket Options with the Use of Liquid Breeder

As candidate blanket concepts for a U.S. advanced reactor power plant design, with consideration of the time frame for ITER development, we assessed first wall and blanket design concepts based on the use of reduced activation ferritic steel as structural material and liquid breeder as the coolant and tritium breeder. The liquid breeder choice includes the conventional molten salt Li 2 BeF 4 and the low melting point molten salts such as LiBeF 3 and LiNaBeF 4 (FLiNaBe). Both self-cooled and dual coolant molten salt options were evaluated. We have also included the dual coolant leadeutectic Pb-17Li design in our assessment. We take advantage of the molten salt low electrical and thermal conductivity to minimize impacts from the MHD effect and the heat losses from the breeder to the actively cooled steel structure. For the Pb-17Li breeder we employ flow channel inserts of SiC f /SiC composite with low electrical and thermal conductivity to perform respective insulation functions. We performed preliminary assessments of these design options in the areas of neutronics, thermal-hydraulics, safety, and power conversion system. Status of the R&D items of selected high performance blanket concepts is reported. Results from this study will form the technical basis for the formulation of the U.S. ITER test module program and corresponding test plan.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simplified gas sensor model based on AlGaN/GaN heterostructure Schottky diode

Physics based modeling of AlGaN/GaN heterostructure Schottky diode gas sensor has been investigated for high sensitivity and linearity of the device. Here the surface and heterointerface properties are greatly exploited. The dependence of two dimensional electron gas (2DEG) upon the surface charges is mainly utilized. The simulation of Schottky diode has been done in Technology Computer Aided Design (TCAD) tool and I-V curves are generated, from the I-V curves 76% response has been recorded in presence of 500 ppm gas at a biasing voltage of 0.95 Volt.

36 MATERIALS SCIENCE↗

Occurrence of magnetoelectric effect correlated to the Dy order in Dy{sub 2}NiMnO{sub 6} double perovskite

Magnetic, dielectric, and ac conductivity as well as room temperature structural and Raman studies are performed on double perovskite Dy{sub 2}NiMnO{sub 6}. The crystal structure of the compound adopts monoclinic P2{sub 1}/n space group, where alternate Mn and Ni distorted octahedral are arranged in anti-phase a{sup −} a{sup −} b{sup +} order in Glazer notation. Magnetization studies show two magnetic transitions around 100 K and 20 K which are related to the ordering of transition and rare earth cations moment, respectively. Temperature dependent dielectric permittivity shows Havriliak-Negami type thermally activated dielectric relaxation. The ac conductivity at different temperature is found to follow Jonscher power law behavior. Time-temperature scaling of the conductivity spectra reveals that the charge transport dynamics is independent of temperature. Intriguingly, an anomaly in the dielectric constant is observed close to the order of Dy moment which indicates intrinsic magnetoelectric coupling. The hybridization between Dy and Ni/Mn is suggested to be correlated with the magnetoelectric coupling.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Status report on assessment of environmentally assisted fatigue for LWR extended service conditions

This report provides an update on an earlier assessment of environmentally assisted fatigue for light water reactor (LWR) materials under extended service conditions. This report is a deliverable in September 2013, under the work package for environmentally assisted fatigue in the Light Water Reactor Sustainability (LWRS) program. The overall objective of this LWRS project is to assess the degradation by environmentally assisted cracking/fatigue of LWR materials, such as various alloy base metals and their welds used in reactor coolant system piping. This effort is to support the U.S. Department of Energy LWRS program for developing tools to predict the aging/failure mechanism and to correspondingly predict the remaining life of LWR components for anticipated 60-80 year operation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Spin correlated dielectric memory and rejuvenation in multiferroic CuCrS{sub 2}

We report a rare consequence of memory effect in dielectric response (ϵ) and magnetic field induced rejuvenation in a relaxor-type multiferroic chalcogenide, CuCrS{sub 2}. Despite reasonably high conductivity, we are able to detect significant spontaneous polarization using an improvised technique verifying ferroelectric (FE) order. Concomitant appearance of both FE and antiferromagnetic orders authenticates multiferroicity. A smeared out FE transition and strong frequency dependence of the broadened peak in ϵ obeying Dynamical scaling law signify relaxor properties. We discuss the role of geometrical frustration in the antiferromagnetically coupled layered triangular lattice and metal ligand hybridization for these unusual properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

June 2013 Update: Status Report on Assessment of Environmentally Assisted Fatigue for LWR Extended Service Conditions

This report provides an update on an earlier assessment of environmentally assisted fatigue for light water reactor (LWR) materials under extended service conditions. This quarterly report is a deliverable in April-June 2013 quarter under the work package for environmentally assisted fatigue in the Light Water Reactor Sustainability (LWRS) program. The overall objective of this LWRS project is to assess the degradation by environmentally assisted cracking/fatigue of LWR materials such as various alloy base metals and their welds used in reactor coolant system piping. This effort is to support the Department of Energy LWRS program for developing tools to predict the aging/failure mechanism and to correspondingly predict the remaining life of LWR components for anticipated 60-80 year operation.

Mohanty, S.↗

Resolution of Qualification Issues for Existing Structural Materials

This report gives a detailed assessment of several key technical issues that needs resolution for the existing structural materials with emphasis on application in liquid metal reactors (LMRs), in particular, sodium cooled fast reactors. The work is a combined effort between Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL) with ANL as the technical lead, as part of Advanced Structural Materials Program for the Advanced Fuel Cycle Initiative (AFCI) Reactor Campaign. The report is the second deliverable in FY09 (M2505050201) under the work package “Advanced Materials Code Qualification”. The overall objective of the Advanced Materials Code Qualification project is to evaluate the key technical requirements for the qualification of currently available and future advanced materials for application in sodium reactor systems and the resolution of issues that the U.S. Nuclear Regulatory Commission (NRC) has raised in the past on structural materials in support of the design and licensing of the LMR. Advanced materials are a critical element in the development of sodium reactor technologies. Enhanced materials performance not only improves safety margins and provides design flexibility, but also is essential for the economics of future advanced sodium reactors. Qualification and licensing of advanced materials are prominent needs for developing and implementing advanced sodium reactor technologies. However, the development of sufficient database and qualification of these materials for application in LMRs require considerable amount of time and resources. In the meantime, the currently available materials will be used in the early development of fast reactors. Nuclear structural component designs in the U.S. comply with the ASME Boiler and Pressure Vessel Code Section III (Rules for Construction of Nuclear Facility Components) and the NRC grants licensing. As the LMR will operate at higher temperatures than the current light water reactors (LWRs), the design of elevated-temperature components must comply with ASME Section III Subsection NH (Class 1 Components in Elevated Temperature Service). Assessment of materials performance issues and high temperature design methodology issues pertinent to the LMR were presented in an earlier report (Natesan et al. 2008). In a subsequent report (Majumdar et al. 2009), we addressed the needs in high temperature methodologies for design of various high temperature components in sodium cooled fast reactor. The present report addresses several key technical issues for the currently available structural materials such as Type 304 and 316 austenitic stainless steels and ferritic steels such as 2.25Cr-1Mo and modified 9Cr-1Mo. The 60-year design life for the LMR presents a significant challenge to the development of database, extrapolation/prediction of long-term performance, and high temperature structural design methodology. The current Subsection NH is applicable to the design life only up to 34 years. No experimental data contain test durations of 525,000 hours, and it is impractical to conduct such long-term tests in any types of testing. So far the longest creep tests for Grade 91 and Grade 92 steels have run up to 100,000 hours. It has been noted that there is a large drop in creep rupture strength in long-term tests for these high-Cr creep-resistant steels, which may result in overestimation of the long-term creep strength and allowable stress. The report addresses in detail the need for a mechanistic understanding of the structural materials, from the standpoint of the effects of thermal aging, creep deformation, creep fracture, fatigue and creep-fatigue, creep-fatigue predictive models, fatigue and creep crack growth, and fracture toughness. Based on an in-depth assessment of the available data and mechanistic understanding, key technical issues are identified and discussed for each of the property areas. Furthermore, we have proposed viable approaches to resolve the issues and prioritized our recommendations.

Natesan, K.↗

Coupled field-structural analysis of HGTR fuel brick using ABAQUS

High-temperature, gas-cooled reactors (HTGRs) are usually helium-gas cooled, with a graphite core that can operate at reactor outlet temperatures much higher than can conventional light water reactors. In HTGRs, graphite components moderate and reflect neutrons. During reactor operation, high temperature and high irradiation cause damage to the graphite crystal and grains and create other defects. This cumulative structural damage during the reactor lifetime leads to changes in graphite properties, which can alter the ability to support the designed loads. The aim of the present research is to develop a finite-element code using commercially available ABAQUS software for the structural integrity analysis of graphite core components under extreme temperature and irradiation conditions. In addition, the Reactor Geometry Generator tool-kit, developed at Argonne National Laboratory, is used to generate finite-element mesh for complex geometries such as fuel bricks with multiple pin holes and coolant flow channels. This paper presents the proposed concept and discusses results of stress analysis simulations of a fuel block with H-451 grade material properties. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Code Qualification of Structural Materials for AFCI Advanced Recycling Reactors

This report summarizes the further findings from the assessments of current status and future needs in code qualification and licensing of reference structural materials and new advanced alloys for advanced recycling reactors (ARRs) in support of Advanced Fuel Cycle Initiative (AFCI). The work is a combined effort between Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL) with ANL as the technical lead, as part of Advanced Structural Materials Program for AFCI Reactor Campaign. The report is the second deliverable in FY08 (M505011401) under the work package 'Advanced Materials Code Qualification'. The overall objective of the Advanced Materials Code Qualification project is to evaluate key requirements for the ASME Code qualification and the Nuclear Regulatory Commission (NRC) approval of structural materials in support of the design and licensing of the ARR. Advanced materials are a critical element in the development of sodium reactor technologies. Enhanced materials performance not only improves safety margins and provides design flexibility, but also is essential for the economics of future advanced sodium reactors. Code qualification and licensing of advanced materials are prominent needs for developing and implementing advanced sodium reactor technologies. Nuclear structural component design in the U.S. must comply with the ASME Boiler and Pressure Vessel Code Section III (Rules for Construction of Nuclear Facility Components) and the NRC grants the operational license. As the ARR will operate at higher temperatures than the current light water reactors (LWRs), the design of elevated-temperature components must comply with ASME Subsection NH (Class 1 Components in Elevated Temperature Service). However, the NRC has not approved the use of Subsection NH for reactor components, and this puts additional burdens on materials qualification of the ARR. In the past licensing review for the Clinch River Breeder Reactor Project (CRBRP) and the Power Reactor Innovative Small Module (PRISM), the NRC/Advisory Committee on Reactor Safeguards (ACRS) raised numerous safety-related issues regarding elevated-temperature structural integrity criteria. Most of these issues remained unresolved today. These critical licensing reviews provide a basis for the evaluation of underlying technical issues for future advanced sodium-cooled reactors. Major materials performance issues and high temperature design methodology issues pertinent to the ARR are addressed in the report. The report is organized as follows: the ARR reference design concepts proposed by the Argonne National Laboratory and four industrial consortia were reviewed first, followed by a summary of the major code qualification and licensing issues for the ARR structural materials. The available database is presented for the ASME Code-qualified structural alloys (e.g. 304, 316 stainless steels, 2.25Cr-1Mo, and mod.9Cr-1Mo), including physical properties, tensile properties, impact properties and fracture toughness, creep, fatigue, creep-fatigue interaction, microstructural stability during long-term thermal aging, material degradation in sodium environments and effects of neutron irradiation for both base metals and weld metals. An assessment of modified versions of Type 316 SS, i.e. Type 316LN and its Japanese version, 316FR, was conducted to provide a perspective for codification of 316LN or 316FR in Subsection NH. Current status and data availability of four new advanced alloys, i.e. NF616, NF616+TMT, NF709, and HT-UPS, are also addressed to identify the R&D needs for their code qualification for ARR applications. For both conventional and new alloys, issues related to high temperature design methodology are described to address the needs for improvements for the ARR design and licensing. Assessments have shown that there are significant data gaps for the full qualification and licensing of the ARR structural materials. Development and evaluation of structural materials require a variety of experimental facilities that have been seriously degraded in the past. The availability and additional needs for the key experimental facilities are summarized at the end of the report. Detailed information covered in each Chapter is given.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development and testing of texture discriminators for the analysis of trabecular bone in proximal femur radiographs

Purpose: Texture analysis of femur radiographs may serve as a potential low cost technique to predict osteoporotic fracture risk and has received considerable attention in the past years. A further application of this technique may be the measurement of the quality of specific bone compartments to provide useful information for treatment of bone fractures. Two challenges of texture analysis are the selection of the best suitable texture measure and reproducible placement of regions of interest (ROIs). The goal of this in vitro study was to automatically place ROIs in radiographs of proximal femur specimens and to calculate correlations between various different texture analysis methods and the femurs' anchorage strength. Methods: Radiographs were obtained from 14 femoral specimens and bone mineral density (BMD) was measured in the femoral neck. Biomechanical testing was performed to assess the anchorage strength in terms of failure load, breakaway torque, and number of cycles. Images were segmented using a framework that is based on the usage of level sets and statistical in-shape models. Five ROIs were automatically placed in the head, upper and lower neck, trochanteric, and shaft compartment in an atlas subject. All other subjects were registered rigidly, affinely, and nonlinearly, and the resulting transformation was used to map the five ROIs onto the individual femora. Results: In each ROI, texture features were extracted using gray level co-occurence matrices (GLCM), third-order GLCM, morphological gradients (MGs), Minkowski dimensions (MDs), Minkowski functionals (MFs), Gaussian Markov random fields, and scaling index method (SIM). Coefficients of determination for each texture feature with parameters of anchorage strength were computed. In a stepwise multiregression analysis, the most predictive parameters were identified in different models. Texture features were highly correlated with anchorage strength estimated by the failure load of up to R{sup 2}=0.61 (MF and MG features, p<0.01) and were partially independent of BMD. The correlations were dependent on the choice of the ROI and the texture measure. The best predictive multiregression model for failure load R{sub adj}{sup 2}=0.86 (p<0.001) included a set of recently developed texture methods (MF and SIM) but excluded bone mineral density and commonly used texture measures. Conclusions: The results suggest that texture information contained in trabecular bone structure visualized on radiographs may predict whether an implant anchorage can be used and may determine the local bone quality from preoperative radiographs.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Core Outlet Temperature Study

It is a known fact that the power conversion plant efficiency increases with elevation of the heat addition temperature. The higher efficiency means better utilization of the available resources such that higher output in terms of electricity production can be achieved for the same size and power of the reactor core or, alternatively, a lower power core could be used to produce the same electrical output. Since any nuclear power plant, such as the Advanced Burner Reactor, is ultimately built to produce electricity, a higher electrical output is always desirable. However, the benefits of the higher efficiency and electricity production usually come at a price. Both the benefits and the disadvantages of higher reactor outlet temperatures are analyzed in this work.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The skeletal structure of insulin-like growth factor I-deficient mice

The importance of insulin-like growth factor I (IGF-I) for growth is well established. However, the lack of IGF-I on the skeleton has not been examined thoroughly. Therefore, we analyzed the structural properties of bone from mice rendered IGF-I deficient by homologous recombination (knockout [k/o]) using histomorphometry, peripheral quantitative computerized tomography (pQCT), and microcomputerized tomography (muCT). The k/o mice were 24% the size of their wild-type littermates at the time of study (4 months). The k/o tibias were 28% and L1 vertebrae were 26% the size of wild-type bones. Bone formation rates (BFR) of k/o tibias were 27% that of the wild-type littermates. The k/o bones responded normally to growth hormone (GH; 1.7-fold increase) and supranormally to IGF-I (5.2-fold increase) with respect to BFR. Cortical thickness of the proximal tibia was reduced 17% in the k/o mouse. However, trabecular bone volume (bone volume/total volume [BV/TV]) was increased 23% (male mice) and 88% (female mice) in the k/o mice compared with wild-type controls as a result of increased connectivity, increased number, and decreased spacing of the trabeculae. These changes were either less or not found in L1. Thus, lack of IGF-I leads to the development of a bone structure, which, although smaller, appears more compact.

NASA Discipline Musculoskeletal↗