Oxidant-assisted methane pyrolysis
Adding small amounts of CO 2 or H 2 O to methane pyrolysis boosts hydrogen and carbon yieldsviacyclic catalyst regeneration, enabling efficient low-carbon hydrogen and crystalline carbon production.
Chemistry↗
Engineering topics
Majumdar, Arun
Publications and source records attributed to Majumdar, Arun.
Co-synthesis of Hydrogen and High-Value Carbon Products from Methane Pyrolysis
The ARPA-E Methane Pyrolysis Project successfully developed a scalable technology for hydrogen production with low-CO x emission through methane pyrolysis, co-producing high-value carbon nanotubes (CNTs). The project focused on optimizing reactor design, enhancing catalyst performance, and assessing techno-economic feasibility to create a commercially viable and environmentally sustainable process. The fluidized bed reactor achieved over 90% methane (CH 4 ) conversion by using a 5% CO 2 co-feed, which stabilizes carbon yields and minimizes catalyst deactivation. This setup allowed for continuous operation across ten cycles, each consisting of a 14-minute pyrolysis phase followed by a 10-minute dislodging phase to remove a fraction of the accumulated carbon, resulting in stable performance and high-quality CNT production. In parallel, monolith reactors coated with Fe demonstrated a sustained methane conversion of 73% while producing CNTs with high crystallinity. Although promising for continuous operation, monolith reactors face challenges in coating durability and scalability, highlighting areas for further optimization in commercial applications. Catalyst formulation played a key role in enhancing process efficiency. The core catalyst used was 5%Fe/Al 2 O 3 (wt%), optimized through wet impregnation, which improved CNT morphology, yielding longer and more uniform CNTs. The catalyst's performance was further enhanced by adding promoters: 2.5 wt% Ni increased methane conversion close to the thermodynamic limit, while 2.5 wt% Mn improved CNT alignment and crystallinity, and 1.5 wt% NaCl boosted CNT morphology but slightly lowered methane conversion. These adjustments allowed the reactor to maintain high methane conversion while producing high-quality CNTs, enabling stable performance over multiple cycles. To address carbon buildup and ensure uninterrupted operation, a pneumatic conveying tube was implemented for effective carbon dislodging in the fluidized bed configuration. CO 2 and H 2 O co-feeds were also introduced to enhance carbon removal, with CO 2 boosting CNT yield by approximately 15%. This setup enabled stable reactor operation across multiple cycles, preventing clogging and minimizing catalyst wear, making the process suitable for industrial scaling. Techno-economic analysis (TEA) projected hydrogen production costs between $\$$1.00 and $\$$1.64 per kilogram, with CNT values assumed at $\$$375/ton and $\$$100/ton. The life cycle assessment showed that CO 2 emissions could be as low as 0.64 kg CO 2 e/kg H 2 at 95% methane conversion assuming an electricity input of 50 kg CO 2 e/MWh. Even at 50% methane conversion, emissions remained below 1 kg CO 2 e/kg H 2 , demonstrating the process's low-emission potential and making it a viable alternative to traditional steam methane reforming. Overall, the results from this project demonstrate the feasibility of a pyrolysis process where carbon is continuously removed from the catalyst surface and hydrogen is continuously produced until a catalyst regeneration step is required to fully clean the catalyst surface and renew catalyst performance. Major open challenges are related to avoiding the loss of catalyst material in the dislodged carbon during fluidized bed conditions, since our best result demonstrated a carbon purity of ~70 wt. % (rest being iron and alumina). A monolith reactor was used to favor dislodgement of carbon compared to fluidized bed conditions but our results do not demonstrate an advantage of the monolith configuration. Catalyst performance was similar to fluidized bed conditions with slower deactivation rates overall, but we could not observe carbon dislodging in any of the tens of experiments that were run at Stanford. Our results show that the most relevant areas of improvement are related to the fundamental understanding of the iron-carbon interface for dislodging, and the development of catalyst that can produce CNTs via a base-growth mechanism such that catalyst is not lost in the dislodgement steps. The final report documents all findings and methodologies in detail, providing a valuable resource for the scientific community. By building on these results, researchers can further advance methane pyrolysis technology, moving toward a more sustainable, scalable pathway for hydrogen production. This work lays the foundation for future research and commercial efforts to reduce emissions in hydrogen production while generating valuable carbon products.
08 HYDROGEN↗
Environmental damping and vibrational coupling of confined fluids within isolated carbon nanotubes
Abstract Because of their large surface areas, nanotubes and nanowires demonstrate exquisite mechanical coupling to their surroundings, promising advanced sensors and nanomechanical devices. However, this environmental sensitivity has resulted in several ambiguous observations of vibrational coupling across various experiments. Herein, we demonstrate a temperature-dependent Radial Breathing Mode (RBM) frequency in free-standing, electron-diffraction-assigned Double-Walled Carbon Nanotubes (DWNTs) that shows an unexpected and thermally reversible frequency downshift of 10 to 15%, for systems isolated in vacuum. An analysis based on a harmonic oscillator model assigns the distinctive frequency cusp, produced over 93 scans of 3 distinct DWNTs, along with the hyperbolic trajectory, to a reversible increase in damping from graphitic ribbons on the exterior surface. Strain-dependent coupling from self-tensioned, suspended DWNTs maintains the ratio of spring-to-damping frequencies, producing a stable saturation of RBM in the low-tension limit. In contrast, when the interior of DWNTs is subjected to a water-filling process, the RBM thermal trajectory is altered to that of a Langmuir isobar and elliptical trajectories, allowing measurement of the enthalpy of confined fluid phase change. These mechanisms and quantitative theory provide new insights into the environmental coupling of nanomechanical systems and the implications for devices and nanofluidic conduits.
36 MATERIALS SCIENCE↗
Machine-Learning-Based Mapping and Modeling of Solar Energy with Ultra-High Spatiotemporal Granularity
Despite the rapid growth of solar energy, we still lack a dynamic, high-fidelity database that tracks the spatiotemporal variations of solar PVs and their associated infrastructures across different places at a spatially resolved scale. The absence of such data presents a barrier to various applications such as solar PV growth projection, solar energy integration, solar incentive design, and climate risk assessment. In this project, we aim to bridge this gap by developing AI-based algorithms to extract granular information about solar PV installations and their associated infrastructures (i.e., distribution grids) from widely available unstructured data like remote sensing images and street views. As a result, we have built the Solar Energy Atlas, a fine-grained, large-scale geospatial overlay of distributed solar PVs and distribution grids. On top of it, we have advanced the understanding of solar adoption and distribution grid vulnerability to climate-induced extremes. Our major contributions can be summarized as follow: (1) By developing new AI algorithms, we have built the most comprehensive solar PV spatiotemporal database covering the entire US. This is the first time we obtained the exact GPS locations, size, subtype, and installation year information for rooftop solar PVs across the US. This database can be used for solar PV growth projection, solar energy integration, solar energy policy analysis and design, and spatially-resolved climate risk assessment. (2) Leveraging this database, we have uncovered the socioeconomic driving factors that are correlated with earlier onset of solar adoption and higher saturated adoption levels. We have identified the heterogeneity in the effects of different types of financial incentives on solar adoption and provided implications for tailoring incentive design based on local income levels to promote equitable solar adoption. (3) We have developed a distribution grid GIS mapping algorithm which can obtain granular geospatial and topology information about distribution grids using multi-modal open data, reducing the dependency on hard-to-obtain smart meter data of conventional approaches. It shows effectiveness in both the U.S. and Sub-Saharan Africa. Using this algorithm, we have uncovered the non-uniform vulnerability of distribution grids to wildfires in California in the aspects of undergrounding protection and Distributed Energy Resources (DER) preparedness. This has provided important implications for improving the affordability and equity of grid adaptation approaches. (3) We have made our produced database publicly available and provided user-friendly interface to enable various stakeholders and the general public to interact with the data. We have also integrated the produced data into the Data Commons platform to enable the public to access the data and correlate it with other location-specific characteristics simply using natural language as queries. The impact of our project is three-fold: (1) New algorithms for mapping solar PVs and distribution grids across space and time, which are open source to facilitate researchers and industry; (2) New databases of solar PVs and distribution grids that have been made publicly available for engineering, social, and policy applications; (3) New understandings and actionable insights on the potential approaches to promoting solar adoption and reducing energy infrastructure vulnerabilities. In this report, we start by discussing the project background and motivation (section 5), followed by the overview of project objectives (section 6). Results and discussion for each task are presented in section 7. Significant accomplishments are summarized in section 8. This report will be concluded by discussing the paths forwards (section 9), products (section 10), and team roles (section 11).
14 SOLAR ENERGY↗
Exploring the potential of non-residential solar to tackle energy injustice
Despite the observed disparities in US residential solar deployment, there is limited insight into whether these disparities exist for the non-residential sector. Here we use DeepSolar, a comprehensive photovoltaic database constructed with satellite imagery, to assess solar deployment equity based on the US Justice40’s disadvantaged community measure. We find that disadvantaged communities have less non-residential solar (–38%), but this disparity is notably higher for residential solar (–67%). Across-state variations are consistent for residential solar (–81% to –49%) yet highly heterogeneous for non-residential solar (–66% to +34%). Using scenarios to explore the potential for microgrids powered by solar on building rooftops larger than 1,000 square metres, we estimate that 63% of disadvantaged communities could meet at least 20% of annual residential electricity demand. Furthermore, our research argues for a new focus on non-residential solar as a way to strengthen resilience and accelerate local deployment of clean energy resources to promote energy justice.
14 SOLAR ENERGY↗
Local and utility-wide cost allocations for a more equitable wildfire-resilient distribution grid
Climate-induced extreme weather conditions make electricity infrastructure more vulnerable. They increase the risk of power-line-ignited wildfires which can, in turn, jeopardize electric power delivery. Here, leveraging machine learning, we show that lower-income communities in California not only have lower fractions of power distribution lines undergrounded, but overhead lines and poles in their neighbourhoods are also more vulnerable to wildfires. Should they bear the cost of undergrounding fire-prone lines themselves, they would have to pay a disproportionately higher cost per household. We propose a cost allocation scheme with an income threshold below which the cost is borne by utility-wide ratepayers and above which the cost is borne locally. This scheme can not only minimize the average of undergrounding costs per household as a share of income, but also homogenize such cost–income ratios across communities. Furthermore, our research demonstrates the opportunity to appropriately integrate existing policies to make electricity infrastructure affordable, equitable and reliable amidst climate change.
24 POWER TRANSMISSION AND DISTRIBUTION↗
Imaging the electron charge density in monolayer MoS 2 at the Ångstrom scale
Four-dimensional scanning transmission electron microscopy (4D-STEM) has recently gained widespread attention for its ability to image atomic electric fields with sub-Ångstrom spatial resolution. These electric field maps represent the integrated effect of the nucleus, core electrons and valence electrons, and separating their contributions is non-trivial. In this paper, we utilized simultaneously acquired 4D-STEM center of mass (CoM) images and annular dark field (ADF) images to determine the projected electron charge density in monolayer MoS 2 . We evaluate the contributions of both the core electrons and the valence electrons to the derived electron charge density; however, due to blurring by the probe shape, the valence electron contribution forms a nearly featureless background while most of the spatial modulation comes from the core electrons. Our findings highlight the importance of probe shape in interpreting charge densities derived from 4D-STEM and the need for smaller electron probes.
36 MATERIALS SCIENCE↗
A semi-continuous process for co-production of CO 2 -free hydrogen and carbon nanotubes via methane pyrolysis
Heterogeneous catalytic pyrolysis of hydrocarbons to produce CO 2 -free hydrogen and high-quality solid carbon have historically been stymied by issues related to catalyst deactivation by carbon formed during pyrolysis on the catalyst surface. In addition, a system that demonstrates sustained performance in terms of high conversion, high H 2 yield, and high quality of produced carbon has remained elusive. Here, we propose and demonstrate a semi-continuous methane pyrolysis process to H 2 and carbon nanotubes (CNTs) consisting of repeated pyrolysis and in situ (i.e., within the reactor) CNT dislodging by vigorous steam/argon fluidization. With this process, we demonstrate 10 process cycles with high H 2 yield from CH 4 and CNT dislodging in a fluidized-bed reactor with an Fe/q-Al 2 O 3 catalyst synthesized by an easily scalable incipient wetness impregnation process. We also identify and present opportunities for future catalyst and process development.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Fluids and Electrolytes under Confinement in Single-Digit Nanopores
Not Available
36 MATERIALS SCIENCE↗
Transport Mediating Core–Shell Photocatalyst Architecture for Selective Alkane Oxidation
The high activation barrier of the C-H bond in methane, combined with the high propensity of methanol and other liquid oxygenates toward overoxidation to CO 2 , have historically posed significant scientific and industrial challenges to the selective and direct conversion of methane to energy-dense fuels and chemical feedstocks. Here, we report a unique core-shell nanostructured photocatalyst, silica encapsulated TiO 2 decorated with AuPd nanoparticles (TiO 2 @SiO 2 -AuPd), that prevents methanol overoxidation on its surface and possesses high selectivity and yield of oxygenates even at high UV intensity. This room-temperature approach achieves high selectivity for oxygenates (94.5%) with a total oxygenate yield of 15.4 mmol/g cat ·h at 9.65 bar total pressure of CH 4 and O 2 . The working principles of this core-shell photocatalyst were also systematically investigated. Finally, this design concept was further demonstrated to be generalizable for the selective oxidation of other alkanes.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Iron-Poor Ferrites for Low-Temperature CO[subscript 2] Conversion via Reverse Water?Gas Shift Thermo
Explore the source record for details and available documents.
Rojas, Jimmy↗
Thermodynamic guiding principles of high-capacity phase transformation materials for splitting H 2 O and CO 2 by thermochemical looping
Here, thermochemical looping splitting of water and carbon dioxide (CO 2 ) with greenhouse-gas-free (GHG-free) energy has the potential to help address the Gt-scale GHG emissions challenge. Reaction thermodynamics largely contributes to the main bottlenecks of cost reduction for thermochemical looping water/CO 2 splitting cycle. Here, we analyze thermodynamic driving forces in such cycles with two-phase ternary ferrites as model systems. We find that cation configurational entropy chiefly determines the change of partial molar entropy with oxygen stoichiometry. In addition, our phase diagram analysis accurately predicts the optimal Fe ratio for maximal water/CO 2 splitting capacity in thermal reduction and in chemical reduction based cycles, underlining the significance of phase boundary positions. With chemical reduction, >10% CO 2 conversion and high oxygen exchange capacity can both be achieved. Furthermore, our reduced Gibbs free energy model illustrates critical thermodynamic factors that influence the water/CO 2 splitting capacity. Our research reveals the thermodynamic driving forces underlying the unconventional high-capacity Fe-poor ferrites, further explained via phase diagrams of Fe–Co–O, Fe–Ni–O and Fe–Mg–O. Future materials improvements can be guided by our reduced Gibbs free energy model.
08 HYDROGEN↗
Coloured low-emissivity films for building envelopes for year-round energy savings
We report that buildings are responsible for over 40% of total US energy use, of which about 40% is directly related to the operation of heating, ventilation and air-conditioning (HVAC) systems. Saving energy to heat and cool buildings would contribute substantially to sustainability. Here we propose a category of coloured low-emissivity films for building walls that constitute the main component of the building thermal envelope. We demonstrate high reflectance (~90%) in infrared wavelength range and selective reflectance in the visible light wavelength range for desired colours. These films can help minimize radiative heat exchange between the indoor and outdoor environments, thus saving energy for all-year cooling and heating while satisfying the required aesthetical effect. Simulations show that these films can help reduce heat gain and loss by up to 257.6 MJ per installation wall area annually. In the case of a typical midrise apartment building, the HVAC system can save up to 124.46 GJ (equal to 9.87% of the building’s HVAC energy consumption). By rough estimation, a global CO 2 emission reduction of 1.14 billion metric tons annually could be achieved. Our work provides insights for innovative energy-saving building envelope materials that can help achieve global carbon neutrality and sustainability.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Application-driven synthesis and characterization of hexagonal boron nitride deposited on metals and carbon nanotubes
Hexagonal boron nitride (h-BN) is unique among two-dimensional materials, with a large band gap (~6 eV) and high in-plane thermal conductivity (>400 W m -1 K -1 ), second only to diamond among electrical insulators. Many studies to date have relied on exfoliated h-BN, however, for large-scale applications the material must be synthesized by methods such as chemical vapor deposition (CVD). Here, we first investigate single-layer h-BN synthesized by CVD on single crystal platinum (Pt), comparing these films with h-BN deposited on more commonly used polycrystalline Pt and Cu. The h-BN film grown on single crystal Pt has the lowest surface roughness and best spatial homogeneity, and our electrochemical transfer process allows the Pt to be reused with no measurable degradation. Additionally, we also demonstrate direct capping of carbon nanotubes (CNTs) with as-grown h-BN, but we find that the direct growth partly degrades the CNT electrical conductivity. On the other hand, we show that transferred monolayer h-BN can serve as an ultrathin barrier which protects MoS2 from damage at high temperatures and discuss other applications that take advantage of the conformal h-BN deposition.
2D materials↗
Photoabsorption Imaging at Nanometer Scales Using Secondary Electron Analysis
Optical imaging with nanometer resolution offers fundamental insights into light–matter interactions. Traditional optical techniques are diffraction limited with a spatial resolution >100 nm. Optical super-resolution and cathodoluminescence techniques have higher spatial resolutions, but these approaches require the sample to fluoresce, which many materials lack. Here, we introduce photoabsorption microscopy using electron analysis, which involves spectrally specific photoabsorption that is locally probed using a scanning electron microscope, whereby a photoabsorption-induced surface photovoltage modulates the secondary electron emission. We demonstrate spectrally specific photoabsorption imaging with sub-20 nm spatial resolution using silicon, germanium, and gold nanoparticles. Theoretical analysis and Monte Carlo simulations are used to explain the basic trends of the photoabsorption-induced secondary electron signal. Based on our current experiments and this analysis, we expect that the spatial resolution can be further improved to a few nanometers, thereby offering a general approach for nanometer-scale optical spectroscopic imaging and material characterization.
77 NANOSCIENCE AND NANOTECHNOLOGY↗