Engineering Papers⌕ Search

Engineering topics

Magliozzi, B.

Publications and source records attributed to Magliozzi, B..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Unified aeroacoustics analysis for high speed turboprop aerodynamics and noise. Volume 5: Propagation of propeller tone noise through a fuselage boundary layer

An analysis of tone noise propagation through a boundary layer and fuselage scattering effects was derived. This analysis is a three dimensional and the complete wave field is solved by matching analytical expressions for the incident and scattered waves in the outer flow to a numerical solution in the boundary layer flow. The outer wave field is constructed analytically from an incident wave appropriate to the source and a scattered wave in the standard Hankel function form. For the incident wave, an existing function - domain propeller noise radiation theory is used. In the boundary layer region, the wave equation is solved by numerical methods. The theoretical analysis is embodied in a computer program which allows the calculation of correction factors for the fuselage scattering and boundary layer refraction effects. The effects are dependent on boundary layer profile, flight speed, and frequency. Corrections can be derived for any point on the fuselage, including those on the opposite side from the source. The theory was verified using limited cases and by comparing calculations with available measurements from JetStar tests of model prop-fans. For the JetStar model scale, the boundary layer refraction effects produce moderate fuselage pressure reinforcements aft of and near the plane of rotation and significant attenuation forward of the plane of rotation at high flight speeds. At lower flight speeds, the calculated boundary layer effects result in moderate amplification over the fuselage area of interest. Apparent amplification forward of the plane of rotation is a result of effective changes in the source directivity due to boundary layer refraction effects. Full scale effects are calculated to be moderate, providing fuselage pressure amplification of about 5 dB at the peak noise location. Evaluation using available noise measurements was made under high-speed, high-altitude flight conditions. Comparisons of calculations made of free field noise, using a current frequency-domain propeller noise prediction method, and fuselage effects using this new procedure show good agreement with fuselage measurements over a wide range of flight speeds and frequencies. Correction factors for the JetStar measurements made on the fuselage are provided in an Appendix.

Magliozzi, B.↗
NASA NTRS1987

Noise characteristics of model counter-rotating Prop-Fans

Results of acoustics tests of 24.5 in. diameter model counter-rotating propfans are presented. In these tests several configurations were investigated, including tractors and pushers downstream of a pylon, both at zero degrees and at four degrees angle-of-attack. The effects on noise of spacing between rotors and between the pylon and the rotors were also measured. Effects of rotor spacing were found to cause small changes in noise. Increasing blade count from 5-front and 5-rear to 6-front and 6-rear results in about a 1 EPNdB reduction in noise. Increasing only the front rotor blade count to six blades resulted in a noise reduction of about 2 EPNdB. The presence of the pylon resulted in a 1 EPNdB increase in noise. Angle of attack effects showed an increase of 3.5 EPNdB for the tractor configuration and only 1.5 EPNdB for the pusher configuration. Tip speed was found to be the strongest parameter in reducing noise. However, for a given thrust loading, an optimum tip speed is seen. Correlations between measurements and predictions are shown to be in good agreement.

Magliozzi, B.↗
NASA NTRS1984

Propagation of propeller tone noise through a fuselage boundary layer

In earlier experimental and analytical studies, it was found that the boundary layer on an aircraft could provide significant shielding from propeller noise at typical transport airplane cruise Mach numbers. In this paper a new three-dimensional theory is described that treats the combined effects of refraction and scattering by the fuselage and boundary layer. The complete wave field is solved by matching analytical expressions for the incident and scattered waves in the outer flow to a numerical solution in the boundary layer flow. The model for the incident waves is a near-field frequency-domain propeller source theory developed previously for free field studies. Calculations for an advanced turboprop (Prop-Fan) model flight test at 0.8 Mach number show a much smaller than expected pressure amplification at the noise directivity peak, strong boundary layer shielding in the forward quadrant, and shadowing around the fuselage. Results are presented showing the difference between fuselage surface and free-space noise predictions as a function of frequency and Mach number. Comparison of calculated and measured effects obtained in a Prop-Fan model flight test show good agreement, particularly near and aft of the plane of rotation at high cruise Mach number.

Hanson, D. B.↗
NASA NTRS1983

Small transport aircraft technology propeller study

A study to define potential benefits of advanced technology propeller for 1985-1990 STAT commuter airplanes was completed. Two baselines, a Convair, 30 passenger, 0.47 Mach number airplane and a Lockheed, 50 passenger, 0.70 Mach number airplane, were selected from NASA-Ames sponsored airframe contracts. Parametric performance, noise level, weight and cost trends for propellers with varying number of blades, activity factor, camber and diameter incorporating blade sweep, tip proplets, advanced composite materials, advanced airfoils, advanced prevision synchrophasing and counter-rotation are presented. The resulting DOC, fuel burned, empty weight and acquisition cost benefits are presented for resizings of the two baseline airplanes. Six-bladed propeller having advanced composite blades, advanced airfoils, tip proplets and advanced prevision synchrophasers provided the maximum DOC improvements for both airplanes. DOC and fuel burned were reduced by 8.3% and 17.0% respectively for the Convair airplane and by 24.9% and 41.2% respectively for the Lockheed airplane. The larger reductions arose from a baseline definition with very heavy fuselage acoustic treatment. An alternate baseline, with a cabin noise 13dB in excess of the objective, was also studied.

Black, B. M.↗
NASA NTRS1980

Acoustic pressures on a prop-fan aircraft fuselage surface

Acoustic pressure amplitude and phase distributions on the surface of a simulated fuselage (a rigid semi-cylinder) installed in an acoustically treated wind tunnel near a Prop-Fan model were measured. The test conditions simulated the relative tip Mach number and blade loading of a full scale Prop-Fan at high altitude 0.8 Mach number cruise. Measurements were also made at equivalent microphone locations without the semi-cylinder to establish the effects of the presence of a fuselage on the sound pressure amplitudes. These effects were found to be 6 dB at 90 degrees incidence, decreasing to no effect at grazing incidence. Comparison of measurements and calculations using a Hamilton Standard Prop-Fan noise calculation computer program showed good agreement in peak level and in phase distribution. Continuous recordings were also made of a Prop-Fan RPM sweep at constant simulated flight speed and a simulated flight speed sweep at constant Prop-Fan RPM. These showed smooth variations in noise level over the tip Mach number range 0.878 to 1.143.

Magliozzi, B.↗
NASA NTRS1979

Advanced turbo-prop airplane interior noise reduction-source definition

Acoustic pressure amplitudes and phases were measured in model scale on the surface of a rigid semicylinder mounted in an acoustically treated wind tunnel near a prop-fan (an advanced turboprop with many swept blades) model. Operating conditions during the test simulated those of a prop-fan at 0.8 Mach number cruise. Acoustic pressure amplitude and phase contours were defined on the semicylinder surface. Measurements obtained without the semi-cylinder in place were used to establish the magnitude of pressure doubling for an aircraft fuselage located near a prop-fan. Pressure doubling effects were found to be 6dB at 90 deg incidence decreasing to no effect at grazing incidence. Comparisons of measurements with predictions made using a recently developed prop-fan noise prediction theory which includes linear and non-linear source terms showed good agreement in phase and in peak noise amplitude. Predictions of noise amplitude and phase contours, including pressure doubling effects derived from test, are included for a full scale prop-fan installation.

Magliozzi, B.↗
NASA NTRS1977

Some measured and calculated effects of forward velocity on propeller noise

Test flights using a twin-engine, high-wing, light STOL transport plane powered by free turbine engines driving three-bladed propellers, were conducted at the NASA Wallops Flight Center. A ground-based acoustic measuring range was set up, and aircraft tracking information was supplied by a radar system. The noise of the unshrouded propeller was measured under static and forward flight conditions, and the measurements were compared with theory. Under static conditions, the principal noise is related to the unsteady loading associated with the interaction of the propeller with persistent turbulent eddies passing through the propeller disk. Through the use of existing prediction techniques, it was shown that changes in the geometry such as different airfoil thickness distribution can affect the radiated acoustic pressure signatures. This test program confirmed that lower propeller noise levels are produced in forward flight than under static conditions and that the most significant reductions occur at the midfrequencies which dominate perceived and A-weighted noise levels.

Pegg, R. J.↗
NASA NTRS1977

The Influence of Forward Flight on Propeller Noise

The effect of flight on blade surface pressures and propeller noise was reported. There were significant differences in blade surface pressures and far-field noise between static and flight conditions. The static data showed many high-intensity, tone-like peaks whereas the flight data was generally free from tones. The turbulence ingested by the propeller operating statically was dominated by long, thin eddies. In flight the scale of the turbulence was greately reduced from that observed statically.

Magliozzi, B.↗
NASA NTRS1976

Progress report on propeller aircraft flyover noise research

Initial results of a program to investigate the sources of noise in unshrouded propellers under forward flight conditions are reported. Tests were conducted using a three-blade full-scale instrumented propeller mounted on a twin-engine aircraft. Measurements included (1) far-field noise at fixed ground stations and at two aircraft wing tip locations, (2) blade surface pressures at seven locations on one of the propeller blades, (3) atmospheric turbulence encountered by the aircraft in flight, and (4) aircraft operating conditions. The results confirm that significantly lower levels of propeller noise are produced in forward flight than at static conditions. It is tentatively concluded that propeller noise generation in flight may be dominated by steady loading at blade passage frequency, but at higher frequencies unsteady loading due to interaction with natural atmospheric turbulence may be the dominant mechanism of noise generation. Under static conditions the total noise signature appears to be the result of interaction of the propeller with persistent turbulent eddies passing through the propeller disk.

Metzger, F. B.↗
NASA NTRS1973

Noise and wake structure measurements in a subsonic tip speed fan

The results of an experimental program are reported which show the effect of blade angle, tip speed, fan pressure ratio, and thrust on noise of a model fan of 0.457m (18 inches) diameter operating at subsonic tip speeds at pressure ratios between 1.06 and 1.15. The fan used in this study had 12 blades, 7 stator vanes, and a spacing between the rotor and stator of 1.85 blade chords. This fan was originally designed for aerodynamic testing and was considered a good performer. It was used in the noise test program as it incorporated features found to reduce noise in an earlier analytical parametric study. For a given pressure ratio the fan was shown to exhibit minimum noise at the blade angle and tip speed near that of maximum aerodynamic efficiency. Also, the noise level and spectrum character of this fan showed excellent correlation with scaled data of a similar larger diameter fan. Results of the program confirm the trends shown in the earlier analytical parametric study which showed that fan noise could be reduced for a given thrust and pressure ratio by increasing fan solidity, improving fan aerodynamic design, and operating the fan at an optimum subsonic tip speed. In addition to noise, the blade wake characteristics at the leading edge of the stator were measured in this program. At root and tip sections some difference between predicted and measured wakes was found. However comparisons between predicted and measured wakes at mid span locations was found to be good.

Magliozzi, B.↗
NASA NTRS1973

Noise and wake structure measurements in a subsonic tip speed fan: Tabulation and plots of test data

Noise and wake structure measurements in a ducted fan were conducted. The tip speed was kept at subsonic levels. The anechoic platform used during the test is described. The following conditions are reported: (1) one third octave band analyses of the fan noise data, (2) narrow band analyses of the fan noise for selected test conditions, (3) narrow band sound power level data for all fan test conditions, and (4) velocity and air angle evaluation of blade wake data.

Magliozzi, B.↗
NASA NTRS1973

Fan and pump noise control

The development is described of improved, low noise level fan and pump concepts for the space shuttle. In addition, a set of noise design criteria for small fans and pumps was derived. The concepts and criteria were created by obtaining Apollo hardware test data to correlate and modify existing noise estimating procedures. A set of space shuttle selection criteria was used to determine preliminary fan and pump concepts. These concepts were tested and modified to obtain noise sources and characteristics which yield the design criteria and quiet, efficient space shuttle fan and pump concepts.

Misoda, J.↗