Engineering Papers⌕ Search

Engineering topics

Maghsoudi, Elham

Publications and source records attributed to Maghsoudi, Elham.

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Europa Clipper Magnetometer Thermal Design Evolution, Validation, and Verification

Europa Clipper Spacecraft is exposed to a high radiation environment and is limited with power. This makes the thermal design of Europa Clipper magnetometer more challenging. The design is required to be highly insulated and at the same time magnetically clean. This paper describes the thermal design evolution of Europa Clipper Magnetometer. A thermal vacuum test is conducted in Europa Clipper orbit’s relevant environment to characterize the requirements and estimate the power consumption. A flight-like engineering model magnetometer from the University of California at Los Angeles (UCLA) is used for this test. Magnetically clean Cernox temperature measurement sensors with the accuracy of ±0.1ºC are used to measure the temperature value inside the sensor head and across the main frame interfaces. This level of accuracy in temperature measurement is required to capture the temperature gradient across the sensor head in a relevant environment which impacts the magnetometer measurement accuracy. Test data is used to correlate the thermal model and characterize the heat leak across the interfaces. Validated thermal model is used as a verification tool for power consumption and thermal requirements.

Caron, Ryan↗
NASA NTRS2020

Psyche Magnetometer Engineering Model Test and Thermal Model Correlation to Validate Operational Thermal Requirement

Psyche Fluxgate Magnetometer candidate fabricated by UCLA has a critical temperature gradient requirement inside the magnetometer sensor head. Since the temperature gradient requirement is a driving factor for the magnetometer operation and science data collection at 16 Psyche, it is critical to validate and verify this requirement via modeling and test. In this work, a thermal vacuum test was completed for Psyche flight-like magnetometer engineering model. Flight-like environments were simulated for a hot operational case (after launch), a cold survival case (cruise), and two cold operational cases to characterize thermal performance of the instrument. An additional, non-flight, steady-state test case was completed to better correlate the magnetometer thermal model. During the test, sensitive Cernox temperature sensors with accuracy of ±0.1°C were used to precisely characterize the temperature gradient and correlate the model to the best accuracy. Collected test data indicated power consumption of 28% lower than predicted. The temperature gradient measured met the expected value and the requirement. Test data indicated the magnetometer also met the AFTs in relevant hot and cold environments. Test Results were used to correlate the thermal model. The correlated thermal model will be integrated to the spacecraft thermal model to predict magnetometer thermal performance while collecting science data in Psyche orbits.

Caron, Ryan↗
NASA NTRS2020

Efficient Thermal Management for Sampling Arm Actuators

An electric actuator incorporating novel features for thermal management is designed and analyzed. Reducing intra-actuator thermal resistance is not only beneficial for cold missions (helping to pre-heat the gearbox) but can also enable high power applications in benign environments. The proposed design increases the thermal conductance between the motor windings and the motor casing by at least two orders of magnitude over the state of practice actuator designs. The design leverages Additive Manufacturing (AM) to integrate a complex 3 dimensional Oscillating Heat Pipe (OHP) directly within the actuator structure. A baseline actuator without this thermal management feature was fabricated. Testing was conducted to evaluate the temperature difference between actuator components at a range of motor winding heat dissipations. An analysis of a proposed revised design incorporating OHPs into the input structure indicated an increase in the effective thermal conductivity of 8 and 22 times for the nominal and start-up modes respectively. In addition, the thermal conductance between the windings and the input structure is increased by a factor of 90, and the thermal conductance between the windings and the gear assembly is increased by a factor of 200 with the proposed design.

Odagiri, Kimihide↗
NASA NTRS2019

Numerical Study of Lander Engine Plume Impingement on the Surface of Europa

Plume exhaust from lander engines would be of concern when landing on the surface of Europa since it could have detrimental effects on both the landing surface and powered descent vehicle. The plume could also entrain particles and redirect them up toward the landing vehicle, as well as erode and contaminate the surface where science would be conducted. In this work, a numerical methodology is developed and validated to conduct a first-order assessment of individual engine plumes of a potential Europa Lander vehicle. Computational Fluid Dynamics (CFD) is used to solve the flow field inside and immediately downstream of the nozzle, while the Direct Simulation Monte Carlo (DSMC) method is applied further downstream where the flow becomes rarefied. An interface between the two domains is defined where macroscopic flow data is passed from the CFD domain to the DSMC domain, establishing a one-way coupling. Plume pressure and velocity fields, as well as ground heating, pressure and density flux profiles, are obtained at altitudes from 25 m down to 10 m, spanning the final stages of landing. The codes and methodologies used in this study are successfully validated with simulations conducted by Morris et al. of the Apollo Lunar Module Descent Engine (LMDE) exhaust plume impinging onto the lunar surface.

Lam, Rebekah↗
NASA NTRS2019

Numerical study of lander engine plume impingement on the surface off Europa

Plume exhaust from lander engines would be of concern when landing on the surface of Europa since it could have detrimental effects on both the landing surface and powered descent vehicle. The plume could also entrain particles and redirect them up toward the landing vehicle, as well as erode and contaminate the surface where science would be conducted. In this work, a numerical methodology is developed and validated to conduct a first-order assessment of individual engine plumes of a potential Europa Lander vehicle. Computational Fluid Dynamics (CFD) is used to solve the flow field inside and immediately downstream of the nozzle, while the Direct Simulation Monte Carlo (DSMC) method is applied further downstream where the flow becomes rarefied. An interface between the two domains is defined where macroscopic flow data is passed from the CFD domain to the DSMC domain, establishing a one-way coupling. Plume pressure and velocity fields, as well as ground heating, pressure and density flux profiles, are obtained at altitudes from 25 m down to 10 m, spanning the final stages of landing. The codes and methodologies used in this study are successfully validated with simulations conducted by Morris et al. [1-3] of the Apollo Lunar Module Descent Engine (LMDE) exhaust plume impinging onto the lunar surface.

Hoey, William↗