Engineering Papers⌕ Search

Engineering topics

Maghami, Peiman G.

Publications and source records attributed to Maghami, Peiman G..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Efficient Jitter Analysis for Spacecraft

Typically in space missions, the science instruments require a specific degree of pointing accuracy as well as dynamical quietness. This dynamical quietness, which is needed to allow the instruments to make measurements (remote sensing applications) or perform other functions, is usually characterized in terms of jitter and stability specifications. In order to insure that the spacecraft meets the requirements of its instruments, several jitter analyses are performed throughout the design phase of the spacecraft and beyond as the models of the spacecraft, its components, and disturbances mature. Each such analysis involves the simulation of the spacecraft and instrument dynamical response to all known disturbance scenarios, followed by the computation of jitter values for each instrument based on the specified jitter time windows. The direct approach for computing jitter values by sweeping maxima and minima throughout the time history may be costly in the computational sense as the size and number of the time histories involved could be quite large. Keeping in mind that typical spacecraft simulation time histories may easily involve hundreds of thousands or millions of points, it is imperative that a jitter analysis algorithm be developed which is more efficient than the direct approach. This paper presents a vectorized algorithm for efficient computation of spacecraft jitter values. The algorithm identifies the extreme points in the time history, which are the points that may dominate the jitter values depending on the location of the jitter window along the time history. The span of influence of each extremum is then computed by the algorithm and used in an efficient and vectorized fashion to obtain the jitter values. The algorithm deals with the multiple jitter windows 2 sequentially, first computing jitter values for the smallest time window, then looping over the remaining time windows until all jitter values are computed. A numerical example is carried out to demonstrate the efficiency and feasibility of the proposed jitter analysis technique.

Maghami, Peiman G.↗
NASA NTRS1998

Fault Accommodation in Control of Flexible Systems

New synthesis techniques for the design of fault accommodating controllers for flexible systems are developed. Three robust control design strategies, static dissipative, dynamic dissipative and mu-synthesis, are used in the approach. The approach provides techniques for designing controllers that maximize, in some sense, the tolerance of the closed-loop system against faults in actuators and sensors, while guaranteeing performance robustness at a specified performance level, measured in terms of the proximity of the closed-loop poles to the imaginary axis (the degree of stability). For dissipative control designs, nonlinear programming is employed to synthesize the controllers, whereas in mu-synthesis, the traditional D-K iteration is used. To demonstrate the feasibility of the proposed techniques, they are applied to the control design of a structural model of a flexible laboratory test structure.

Maghami, Peiman G.↗
NASA NTRS1997

PLATSIM: A Simulation and Analysis Package for Large-Order Flexible Systems

The software package PLATSIM provides efficient time and frequency domain analysis of large-order generic space platforms. PLATSIM can perform open-loop analysis or closed-loop analysis with linear or nonlinear control system models. PLATSIM exploits the particular form of sparsity of the plant matrices for very efficient linear and nonlinear time domain analysis, as well as frequency domain analysis. A new, original algorithm for the efficient computation of open-loop and closed-loop frequency response functions for large-order systems has been developed and is implemented within the package. Furthermore, a novel and efficient jitter analysis routine which determines jitter and stability values from time simulations in a very efficient manner has been developed and is incorporated in the PLATSIM package. In the time domain analysis, PLATSIM simulates the response of the space platform to disturbances and calculates the jitter and stability values from the response time histories. In the frequency domain analysis, PLATSIM calculates frequency response function matrices and provides the corresponding Bode plots. The PLATSIM software package is written in MATLAB script language. A graphical user interface is developed in the package to provide convenient access to its various features.

Maghami, Peiman G.↗
NASA NTRS1997

Design of Neural Networks for Fast Convergence and Accuracy: Dynamics and Control

A procedure for the design and training of artificial neural networks, used for rapid and efficient controls and dynamics design and analysis for flexible space systems, has been developed. Artificial neural networks are employed, such that once properly trained, they provide a means of evaluating the impact of design changes rapidly. Specifically, two-layer feedforward neural networks are designed to approximate the functional relationship between the component/spacecraft design changes and measures of its performance or nonlinear dynamics of the system/components. A training algorithm, based on statistical sampling theory, is presented, which guarantees that the trained networks provide a designer-specified degree of accuracy in mapping the functional relationship. Within each iteration of this statistical-based algorithm, a sequential design algorithm is used for the design and training of the feedforward network to provide rapid convergence to the network goals. Here, at each sequence a new network is trained to minimize the error of previous network. The proposed method should work for applications wherein an arbitrary large source of training data can be generated. Two numerical examples are performed on a spacecraft application in order to demonstrate the feasibility of the proposed approach.

Maghami, Peiman G.↗
NASA NTRS1997

Integrated Controls-Structures Design Methodology: Redesign of an Evolutionary Test Structure

An optimization-based integrated controls-structures design methodology for a class of flexible space structures is described, and the phase-0 Controls-Structures-Integration evolutionary model, a laboratory testbed at NASA Langley, is redesigned using this integrated design methodology. The integrated controls-structures design is posed as a nonlinear programming problem to minimize the control effort required to maintain a specified line-of-sight pointing performance, under persistent white noise disturbance. Static and dynamic dissipative control strategies are employed for feedback control, and parameters of these controllers are considered as the control design variables. Sizes of strut elements in various sections of the CEM are used as the structural design variables. Design guides for the struts are developed and employed in the integrated design process, to ensure that the redesigned structure can be effectively fabricated. The superiority of the integrated design methodology over the conventional design approach is demonstrated analytically by observing a significant reduction in the average control power needed to maintain specified pointing performance with the integrated design approach.

Maghami, Peiman G.↗
NASA NTRS1997

Efficient Computation of Closed-loop Frequency Response for Large Order Flexible Systems

An efficient and robust computational scheme is given for the calculation of the frequency response function of a large order, flexible system implemented with a linear, time invariant control system. Advantage is taken of the highly structured sparsity of the system matrix of the plant based on a model of the structure using normal mode coordinates. The computational time per frequency point of the new computational scheme is a linear function of system size, a significant improvement over traditional, full-matrix techniques whose computational times per frequency point range from quadratic to cubic functions of system size. This permits the practical frequency domain analysis of systems of much larger order than by traditional, full-matrix techniques. Formulations are given for both open and closed loop loop systems. Numerical examples are presented showing the advantages of the present formulation over traditional approaches, both in speed and in accuracy. Using a model with 703 structural modes, a speed-up of almost two orders of magnitude was observed while accuracy improved by up to 5 decimal places.

Maghami, Peiman G.↗
NASA NTRS1996

Experimental Validation of an Integrated Controls-Structures Design Methodology

The first experimental validation of an integrated controls-structures design methodology for a class of large order, flexible space structures is described. Integrated redesign of the controls-structures-interaction evolutionary model, a laboratory testbed at NASA Langley, was described earlier. The redesigned structure was fabricated, assembled in the laboratory, and experimentally tested against the original structure. Experimental results indicate that the structure redesigned using the integrated design methodology requires significantly less average control power than the nominal structure with control-optimized designs, while maintaining the required line-of-sight pointing performance. Thus, the superiority of the integrated design methodology over the conventional design approach is experimentally demonstrated. Furthermore, amenability of the integrated design structure to other control strategies is evaluated, both analytically and experimentally. Using Linear-Quadratic-Guassian optimal dissipative controllers, it is observed that the redesigned structure leads to significantly improved performance with alternate controllers as well.

Maghami, Peiman G.↗
NASA NTRS1995

A class of stabilizing controllers for flexible multibody systems

The problem of controlling a class of nonlinear multibody flexible space systems consisting of a flexible central body to which a number of articulated appendages are attached is considered. Collocated actuators and sensors are assumed, and global asymptotic stability of such systems is established under a nonlinear dissipative control law. The stability is shown to be robust to unmodeled dynamics and parametric uncertainties. For a special case in which the attitude motion of the central body is small, the system, although still nonlinear, is shown to be stabilized by linear dissipative control laws. Two types of linear controllers are considered: static dissipative (constant gain) and dynamic dissipative. The static dissipative control law is also shown to provide robust stability in the presence of certain classes of actuator and sensor nonlinearities and actuator dynamics. The results obtained for this special case can also be readily applied for controlling single-body linear flexible space structures. For this case, a synthesis technique for the design of a suboptimal dynamic dissipative controller is also presented. The results obtained in this paper are applicable to a broad class of multibody and single-body systems such as flexible multilink manipulators, multipayload space platforms, and space antennas. The stability proofs use the Lyapunov approach and exploit the inherent passivity of such systems.

Joshi, Suresh M.↗
NASA NTRS1995

Efficient eigenvalue assignment by state and output feedback with applications for large space structures

The erection and deployment of large flexible structures having thousands of degrees of freedom requires controllers based on new techniques of eigenvalue assignment that are computationally stable and more efficient. Scientists at NASA Langley Research Center have developed a novel and efficient algorithm for the eigenvalue assignment of large, time-invariant systems using full-state and output feedback. The objectives of this research were to improve upon the output feedback version of this algorithm, to produce a toolbox of MATLAB functions based on the efficient eigenvalue assignment algorithm, and to experimentally verify the algorithm and software by implementing controllers designed using the MATLAB toolbox on the phase 2 configuration of NASA Langley's controls-structures interaction evolutionary model, a laboratory model used to study space structures. Results from laboratory tests and computer simulations show that effective controllers can be designed using software based on the efficient eigenvalue assignment algorithm.

Vannell, Eric C.↗
NASA NTRS1994

Experimental validation of an integrated controls-structures design methodology for a class of flexible space structures

This paper describes the first experimental validation of an optimization-based integrated controls-structures design methodology for a class of flexible space structures. The Controls-Structures-Interaction (CSI) Evolutionary Model, a laboratory test bed at Langley, is redesigned based on the integrated design methodology with two different dissipative control strategies. The redesigned structure is fabricated, assembled in the laboratory, and experimentally compared with the original test structure. Design guides are proposed and used in the integrated design process to ensure that the resulting structure can be fabricated. Experimental results indicate that the integrated design requires greater than 60 percent less average control power (by thruster actuators) than the conventional control-optimized design while maintaining the required line-of-sight performance, thereby confirming the analytical findings about the superiority of the integrated design methodology. Amenability of the integrated design structure to other control strategies is considered and evaluated analytically and experimentally. This work also demonstrates the capabilities of the Langley-developed design tool CSI DESIGN which provides a unified environment for structural and control design.

Maghami, Peiman G.↗
NASA NTRS1993

Validated technology for the reduction of spacecraft vibrations - Controls-Structures Integration (CSI)

The NASA Langley Research Center has constructed several testbeds to assess the viability of flexible structure control. It is found, however, that simply adding sensors, actuators, and a control system to an existing structure (i.e. space platform) is not the preferred methodology for improving pointing performance. When the structure is designed without regard to pointing control, significant design freedom is lost. The preferred design procedure is to simultaneously design the structure and the control system, hence, the name Controls-Structures Integration. By designing the structure and control system simultaneously, much higher efficiency can be achieved. In this study, an 18 m long truss structure with several appendages was enhanced through integrated controls and structures design. The design was fabricated and tested for validation of the methodology. Test results collaborated predictions and showed a 60 percent reduction in control energy for the enhanced test article.

Newsom, Jerry R.↗
NASA NTRS1993

Experimental validation of optimization-based integrated controls-structures design methodology for flexible space structures

An optimization-based integrated design approach for flexible space structures is experimentally validated using three types of dissipative controllers, including static, dynamic, and LQG dissipative controllers. The nominal phase-0 of the controls structure interaction evolutional model (CEM) structure is redesigned to minimize the average control power required to maintain specified root-mean-square line-of-sight pointing error under persistent disturbances. The redesign structure, phase-1 CEM, was assembled and tested against phase-0 CEM. It is analytically and experimentally demonstrated that integrated controls-structures design is substantially superior to that obtained through the traditional sequential approach. The capability of a software design tool based on an automated design procedure in a unified environment for structural and control designs is demonstrated.

Maghami, Peiman G.↗
NASA NTRS1993

On eigensystem assignment with dissipativity constraints

Stability of the closed-loop system is of vital importance when controller synthesis is being performed using a reduced order model of the open-loop plant. For passive systems such as flexible space structures, closed-loop stability is often ensured by low-authority dissipative controllers using collocated and compatible sensors and actuators. This paper considers the problem of eigensystem assignment for flexible structures using constant-gain output feedback, under the dissipativity constraints requiring that the gain matrices be nonnegative definite. A novel method is developed in which a sequential procedure is used to assign one complex-conjugate pair of closed-loop eigenvalues in each step. At each step, an iterative technique is employed for generating a nonnegative definite gain matrix that assigns a new pair while keeping the previously assigned pairs unchanged. This method can assign up to m closed-loop system eigenvalues, where m is the number of control inputs. A numerical example of damping enhancement for a large flexible structure is presented to demonstrate the approach.

Maghami, Peiman G.↗
NASA NTRS1993

Integrated design of the CSI evolutionary structure: A verification of the design methodology

One of the main objectives of the Controls-Structures Interaction (CSI) program is to develop and evaluate integrated controls-structures design methodology for flexible space structures. Thus far, integrated design methodologies for a class of flexible spacecraft, which require fine attitude pointing and vibration suppression with no payload articulation, have been extensively investigated. Various integrated design optimization approaches, such as single-objective optimization, and multi-objective optimization, have been implemented with an array of different objectives and constraints involving performance and cost measures such as total mass, actuator mass, steady-state pointing performance, transient performance, control power, and many more. These studies have been performed using an integrated design software tool (CSI-DESIGN CODE) which is under development by the CSI-ADM team at the NASA Langley Research Center. To date, all of these studies, irrespective of the type of integrated optimization posed or objectives and constraints used, have indicated that integrated controls-structures design results in an overall spacecraft design which is considerably superior to designs obtained through a conventional sequential approach. Consequently, it is believed that validation of some of these results through fabrication and testing of a structure which is designed through an integrated design approach is warranted. The objective of this paper is to present and discuss the efforts that have been taken thus far for the validation of the integrated design methodology.

Maghami, Peiman G.↗
NASA NTRS1993

Model reduction in integrated controls-structures design

It is the objective of this paper to present a model reduction technique developed for the integrated controls-structures design of flexible structures. Integrated controls-structures design problems are typically posed as nonlinear mathematical programming problems, where the design variables consist of both structural and control parameters. In the solution process, both structural and control design variables are constantly changing; therefore, the dynamic characteristics of the structure are also changing. This presents a problem in obtaining a reduced-order model for active control design and analysis which will be valid for all design points within the design space. In other words, the frequency and number of the significant modes of the structure (modes that should be included) may vary considerably throughout the design process. This is also true as the locations and/or masses of the sensors and actuators change. Moreover, since the number of design evaluations in the integrated design process could easily run into thousands, any feasible order-reduction method should not require model reduction analysis at every design iteration. In this paper a novel and efficient technique for model reduction in the integrated controls-structures design process, which addresses these issues, is presented.

Maghami, Peiman G.↗
NASA NTRS1993

An optimization-based integrated controls-structures design methodology for flexible space structures

An approach for an optimization-based integrated controls-structures design is presented for a class of flexible spacecraft that require fine attitude pointing and vibration suppression. The integrated design problem is posed in the form of simultaneous optimization of both structural and control design variables. The approach is demonstrated by application to the integrated design of a generic space platform and to a model of a ground-based flexible structure. The numerical results obtained indicate that the integrated design approach can yield spacecraft designs that have substantially superior performance over a conventional design wherein the structural and control designs are performed sequentially. For example, a 40-percent reduction in the pointing error is observed along with a slight reduction in mass, or an almost twofold increase in the controlled performance is indicated with more than a 5-percent reduction in the overall mass of the spacecraft (a reduction of hundreds of kilograms).

Maghami, Peiman G.↗