Engineering Papers⌕ Search

Engineering topics

Maggos, Laura

Publications and source records attributed to Maggos, Laura.

Development of a Pyroprocessing Flowsheet Model for Safeguards Analysis

Pyroprocessing flowsheets have been designed that have efficient actinide recovery, meet nonproliferation objectives, minimize waste, and are commercially viable. The analysis of safeguards of pyrochemical recycle systems for the treatment of used fast reactor metal fuel can be greatly enhanced with the employment of robust dynamic models. Electrochemical process modeling also contributes to broader objectives of the MPACT program by supporting MC&A, options screening, and safeguards analysis and can inform development of sensor systems for a used fuel recycle facility. Modeling can also provide a method for defining metrics and requirements on advanced analysis techniques.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Addendum to UREX Flowsheet for Cleanup of a Spent 130 g-U/L Uranyl Sulfate SHINE Target Solution (March 29, 2012)

The UREX flowsheet described in the original letter report was designed so that it could be used (with modifications in flow rates) for a variety of uranium feed concentrations and for either uranyl-nitrate or uranyl-sulfate SHINE target solutions. Because use of a uranyl-nitrate SHINE target solution (STS) is becoming a less and less probable option, the flowsheet was reevaluated. For both sulfate and nitrate STSs, the UREX feed will be a uranyl-nitrate solution; however, the uranium-nitrate product solution will be treated in completely different ways. In the case of a nitrate STS, the uranium product (after Tc/I-removal and a diluent-wash steps) will only need to be concentrated and pH adjusted before return to the SHINE vessel. In the case of a sulfate STS, the solution will need to be thermally converted to an oxide and then dissolved in sulfuric acid. A multistage scrub-section 2 is required for a nitrate STS, to scrub acetohydroxamic acid (AHA) from the U-loaded solvent entering the strip section, to assure that the concentration of AHA in the U product is essentially zero. However, for a sulfate STS, any process that destroys nitrate will also destroy AHA, so AHA removal from the U-loaded solvent is not important. This could call for the total elimination of the scrub-2 section, but this scrub does have a second purpose: to maintain a higher nitric-acid concentration in the scrub 1 section while keeping the acid concentration low in the scrub-1 feed. AHA is less stable to hydrolysis as the acid concentration increases; by keeping the acidity in the first scrub low (0.1 M), the destruction rate for AHA is low enough for a solution to be stable for 1–2 days.

Vandegrift, George F.↗

Letter Report: UREX Flowsheet for Cleanup of a Spent 130 g-U/L Uranyl Sulfate SHINE Target Solution

On July 6, 2011, Argonne sent two UREX flowsheets to Morgridge Institute for Research (MIR) for processing a 150 and 300 g-U/L solution of uranyl nitrate. Argonne was tasked by the National Nuclear Security Agency (NNSA) in Fiscal Year 2012 (FY-12) to develop a method to clean up a spent SHINE target solution prepared with uranyl sulfate. This process is described above. Discussions between Argonne and SHINE led to us look at a solution of 130 g-U/L solution of uranyl sulfate in sulfuric acid at pH 1. Briefly described below is the UREX flowsheet that was designed using the Argonne Model for Universal Solvent Extraction (AMUSE) for recovering pure uranium from that solution after it has been converted to nitrate media. The barium precipitation of sulfate is so effective that the number of stages developed for treating this solution is exactly the same as for the two earlier flowsheets. The only parameter that needed to be changed is the organic-to-aqueous (O/A) flow ratio in the extraction section. This ratio is maintained to provide a maximum loading of the tributyl phosphate (TBP) in the solvent to a range of 70–72%. This ratio should be kept high enough to minimize the extraction of other species into the solvent (to assure maximum decontamination of the uranium product), but low enough so that the organic phase will not divide into a light and heavy phase (third-phase formation) that would cause significant hydraulic problems for the contactor. As it was initially designed, an important feature of this flowsheet is the ease developing a new flowsheet if the concentration of uranium is modified. This means that the contactor in the hot cell can be permanently plumbed into four sections, with the requisite number of stages in each section. The only variable to be changed if the uranium concentration is modified is the flow rate of feed solutions.

Vandegrift, George F.↗

Requirements for a Dynamic Solvent Extraction Module to Support Development of Advanced Technologies for the Recycle of Used Nuclear Fuel

The Department of Energy's Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program has been established to create and deploy next generation, verified and validated nuclear energy modeling and simulation capabilities for the design, implementation, and operation of future nuclear energy systems to improve the U.S. energy security. As part of the NEAMS program, Integrated Performance and Safety Codes (IPSC's) are being produced to significantly advance the status of modeling and simulation of energy systems beyond what is currently available to the extent that the new codes be readily functional in the short term and extensible in the longer term. The four IPSC areas include Safeguards and Separations, Reactors, Fuels, and Waste Forms. As part of the Safeguards and Separations (SafeSeps) IPSC effort, interoperable process models are being developed that enable dynamic simulation of an advanced separations plant. A SafeSepss IPSC 'toolkit' is in development to enable the integration of separation process modules and safeguards tools into the design process by providing an environment to compose, verify and validate a simulation application to be used for analysis of various plant configurations and operating conditions. The modules of this toolkit will be implemented on a modern, expandable architecture with the flexibility to explore and evaluate a wide range of process options while preserving their stand-alone usability. Modules implemented at the plant-level will initially incorporate relatively simple representations for each process through a reduced modeling approach. Final versions will incorporate the capability to bridge to subscale models to provide required fidelity in chemical and physical processes. A dynamic solvent extraction model and its module implementation are needed to support the development of this integrated plant model. As a stand-alone application, it will also support solvent development of extraction flowsheets and integrated safeguards approaches within the Fuel Cycle Research and Development (FCR&D) Program. The purpose of this document is to identify the requirements for this dynamic solvent extraction model to guide process modelers and code developers to produce a computational module that meets anticipated future needs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗