Engineering topics

Maestrini, Alain

Publications and source records attributed to Maestrini, Alain.

At least 19 records

NASA NTRS2021

A 1-D Submm-wave Leaky-Wave Phased Array using MEMS Phase Shifters

Beam-scanning of submillimeter-wave spectrometers and radiometers have traditionally been implemented using mechanical scanning mechanisms due to the absence of lowloss electronic phase shifters. Recently developed waveguideintegrated MEMS phase shifters are paving the way to realize electronic beam-steering using submm-wave phased arrays. In this work, two phased array demonstrators are presented that operate from 500GHz to 600GHz. A 20 dB directivity 8 ? 1 leaky-wave antenna array will be demonstrated, using fixed waveguide feeding networks, to be capable of ?20? scanning with a scan loss less than 1:7 dB. Secondly, an equivalent but smaller 17 dB directivity 4 ? 1 array will be integrated with MEMS phase shifters to demonstrate a dynamic scanning capability over a ?9:5? range. The antenna array is based on closely sampled square waveguides, terminated with a double-iris, in close proximity of a low permittivity superstrate in order to reduce the grating lobes at larger scanning angles. Measurements are expected to be presented at the conference.

Chattopadhyay, Goutam↗

NASA NTRS2020

Integrated Silicon Platform for Co-planar Design of Vertically Stacked 2.06 THz Mixer Module

The process for fabricating and utilizing the threedimensional Si stack receiver front-end is described in this paper. The capability to have exact dimensionality becomes essential as frequency scales due to the complexity arising in assembly and finer tolerances. Total process yields can be improved through Si fabrication by verifying achievement of specified tolerances lithographically and compatibility to rapid process changes and design fine-tuning. The integrated Si platform with the mounted device is shown in Figure 1. Signal I/O and alignment modalities enable lownoise measurements. Silicon micromachining provides the necessary accuracy for integration at the several THz regime. Particularly, processing and etch recipes have demonstrated smooth surfaces of < 1 μm surface roughness. In consideration is pre-compensating for minute offsets, matching mechanical strain on all interfaces, and including passive alignment verification in the design. As compared to metal blocks, computer numerical controlled (CNC) milling can produce slight burrs in the interfaces resulting in misalignment and resultant strain between two pieces of components. Furthermore, Si integration can make possible arrays of pixel transceivers through compact subsystems for the purpose of measuring multiple lines of spectral content simultaneously in space.

Mehdi, Imran↗

NASA NTRS2020

Integrated Silicon Platform for Co-planar Design of Vertically Stacked 2.06 THz Mixer Module

UNKNOWN

Mehdi, Imran↗

NASA NTRS2013

Submillimeter Planetary Atmospheric Chemistry Exploration Sounder

Planetary Atmospheric Chemistry Exploration Sounder (SPACES), a high-sensitivity laboratory breadboard for a spectrometer targeted at orbital planetary atmospheric analysis. The frequency range is 520 to 590 GHz, with a target noise temperature sensitivity of 2,500 K for detecting water, sulfur compounds, carbon compounds, and other atmospheric constituents. SPACES is a prototype for a powerful tool for the exploration of the chemistry and dynamics of any planetary atmosphere. It is fundamentally a single-pixel receiver for spectral signals emitted by the relevant constituents, intended to be fed by a fixed or movable telescope/antenna. Its front-end sensor translates the received signal down to the 100-MHz range where it can be digitized and the data transferred to a spectrum analyzer for processing, spectrum generation, and accumulation. The individual microwave and submillimeter wave components (mixers, LO high-powered amplifiers, and multipliers) of SPACES were developed in cooperation with other programs, although with this type of instrument in mind. Compared to previous planetary and Earth science instruments, its broad bandwidth (approx. =.13%) and rapid tunability (approx. =.10 ms) are new developments only made possible recently by the advancement in submillimeter circuit design and processing at JPL.

Schlecht, Erich T.↗

NASA NTRS2012

Local Oscillator Sub-Systems for Array Receivers in the 1-3 THz Range

Recent results from the Heterodyne Instrument for the Far-Infrared (HIFI) on the Herschel Space Telescope have confirmed the usefulness of high resolution spectroscopic data for a better understanding of our Universe. This paper will explore the current status of tunable local oscillator sources with emphasis on building a multi-pixel LO subsystem for the scientifically important CII line around 1908 GHz. Recent results have shown that over 50 microwatts of output power at 1.9 THz are possible with an optimized single pixel LO chain. These power levels are now sufficient to pump array receivers in this frequency range. Further power enhancement can be obtained by cooling the chain to 120 K or by utilizing in-phase power combining technology.

local oscillators↗

NASA NTRS2011

All-Solid-State 2.45-to-2.78-THz Source

Sources in the THz range are required in order for NASA to implement heterodyne instruments in this frequency range. The source that has been demonstrated here will be used for an instrument on the SOFIA platform as well as for upcoming astrophysics missions. There are currently no electronic sources in the 2 3- THz frequency range. An electronically tunable compact source in this frequency range is needed for lab spectroscopy as well as for compact space-deployable heterodyne receivers. This solution for obtaining useful power levels in the 2 3- THz range is based on utilizing power-combined multiplier stages. Utilizing power combining, the input power can be distributed between different multiplier chips and then recombined after the frequency multiplication. A continuous wave (CW) coherent source covering 2.48 2.75 THz, with greater than 10 percent instantaneous and tuning bandwidth, and having l 14 W of output power at room temperature, has been demonstrated. This source is based on a 91.8 101.8-GHz synthesizer followed by a power amplifier and three cascaded frequency triplers. It demonstrates that purely electronic solid-state sources can generate a useful amount of power in a region of the electromagnetic spectrum where lasers (solid-state or gas) were previously the only available coherent sources. The bandwidth, agility, and operability of this THz source has enabled wideband, high-resolution spectroscopic measurements of water, methanol, and carbon monoxide with a resolution and signal-to-noise ratio unmatched by other existing systems, providing new insight in the physics of these molecules. Further - more, the power and optical beam quality are high enough to observe the Lamb-dip effect in water. The source frequency has an absolute accuracy better than 1 part in 1012, and the spectrometer achieves sub-Doppler frequency resolution better than 1 part in 108. The harmonic purity is better than 25 dB. This source can serve as a local oscillator for a variety of heterodyne systems, and can be used as a method for precision control of more powerful but much less frequency-agile quantum mechanical terahertz sources.

Mehdi, Imran↗

NASA NTRS2011

A 2.5-2.7 THz Room Temperature Electronic Source

We report on a room temperature 2.5 to 2.7 THz electronic source based on frequency multipliers. The source utilizes a cascade of three frequency multipliers with W-band power amplifiers driving the first stage multiplier. Multiple-chip multipliers are utilized for the two initial stages to improve the power handling capability and a sub-micron anode is utilized for the final stage tripler. Room temperature measurements indicate that the source can put out a peak power of about 14 microwatts with more than 4 microwatts in the 2.5 to 2.7 THz range.

Varactor diodes↗

NASA NTRS2010

Diamond Heat-Spreader for Submillimeter-Wave Frequency Multipliers

The planar GaAs Shottky diode frequency multiplier is a critical technology for the local oscillator (LO) for submillimeter- wave heterodyne receivers due to low mass, tenability, long lifetime, and room-temperature operation. The use of a W-band (75-100 GHz) power amplifier followed by a frequency multiplier is the most common for submillimeter-wave sources. Its greatest challenge is to provide enough input power to the LO for instruments onboard future planetary missions. Recently, JPL produced 800 mW at 92.5 GHz by combining four MMICs in parallel in a balanced configuration. As more power at W-band is available to the multipliers, their power-handling capability be comes more important. High operating temperatures can lead to degradation of conversion efficiency or catastrophic failure. The goal of this innovation is to reduce the thermal resistance by attaching diamond film as a heat-spreader on the backside of multipliers to improve their power-handling capability. Polycrystalline diamond is deposited by hot-filament chemical vapor deposition (CVD). This diamond film acts as a heat-spreader to both the existing 250- and 300-GHz triplers, and has a high thermal conductivity (1,000-1,200 W/mK). It is approximately 2.5 times greater than copper (401 W/mK) and 20 times greater than GaAs (46 W/mK). It is an electrical insulator (resistivity approx. equals 10(exp 15) Ohms-cm), and has a low relative dielectric constant of 5.7. Diamond heat-spreaders reduce by at least 200 C at 250 mW of input power, compared to the tripler without diamond, according to thermal simulation. This superior thermal management provides a 100-percent increase in power-handling capability. For example, with this innovation, 40-mW output power has been achieved from a 250-GHz tripler at 350-mW input power, while the previous triplers, without diamond, suffered catastrophic failures. This breakthrough provides a stepping-stone for frequency multipliers-based LO up to 3 THz. The future work for this design is to apply the high output power from both the 250 and 300 GHz to multiple chains in order to generate milliwatts at 2.3 THz. Using the first generation of results for this innovation, 40 mW of output power were produced from a 240-GHz tripler at 350-mW input power, and 27- mW output power was produced from a 300-GHz tripler at 408-mW input power. This is two times higher than the current state-of-the-art output power capability. A finite-element thermal simulation also shows that 30-microns thick diamond dropped the temperature of the anodes by at least 200 C.

Lin, Robert H.↗

NASA NTRS2010

High Power Local Oscillator Sources for 1-2 THz

Recent results from the Heterodyne Instrument for Far-Infrared (HIFI) on the Herschel Space Telescope have confirmed the usefulness of high resolution spectroscopic data for a better understanding of our Universe. This paper will explore the current status of tunable local oscillator sources beyond HIFI and provide demonstration of how power combining of GaAs Schottky diodes can be used to increase both power and upper operating frequency for heterodyne receivers. Availability of power levels greater than 1 watt in the W-band now makes it possible to design a 1900 GHz source with more than 100 microwatts of expected output power.

Schottky diodes↗

NASA NTRS2010

Quad-Chip Double-Balanced Frequency Tripler

Solid-state frequency multipliers are used to produce tunable broadband sources at millimeter and submillimeter wavelengths. The maximum power produced by a single chip is limited by the electrical breakdown of the semiconductor and by the thermal management properties of the chip. The solution is to split the drive power to a frequency tripler using waveguides to divide the power among four chips, then recombine the output power from the four chips back into a single waveguide. To achieve this, a waveguide branchline quadrature hybrid coupler splits a 100-GHz input signal into two paths with a 90 relative phase shift. These two paths are split again by a pair of waveguide Y-junctions. The signals from the four outputs of the Y-junctions are tripled in frequency using balanced Schottky diode frequency triplers before being recombined with another pair of Y-junctions. A final waveguide branchline quadrature hybrid coupler completes the combination. Using four chips instead of one enables using four-times higher power input, and produces a nearly four-fold power output as compared to using a single chip. The phase shifts introduced by the quadrature hybrid couplers provide isolation for the input and output waveguides, effectively eliminating standing waves between it and surrounding components. This is accomplished without introducing the high losses and expense of ferrite isolators. A practical use of this technology is to drive local oscillators as was demonstrated around 300 GHz for a heterodyne spectrometer operating in the 2-3-THz band. Heterodyne spectroscopy in this frequency band is especially valuable for astrophysics due to the presence of a very large number of molecular spectral lines. Besides high-resolution radar and spectrographic screening applications, this technology could also be useful for laboratory spectroscopy.

Lin, Robert H.↗

NASA NTRS2009

Broadband Sources in the 1-3 THz Range

Broadband electronically tunable sources in the terahertz range are a critical technology for enabling space-borne as well as ground-based applications. By power-combining MMIC amplifier and frequency tripler chips, we have recently demonstrated >1 mW of output power at 900 GHz. This source provides a stepping stone to enable sources in the 2-3 THz range than can sufficiently pump multi-pixel imaging arrays.

sources↗

NASA NTRS2009

In-Phase Power-Combined Frequency Tripler at 300 GHz

This design starts with commercial 85- to 115-GHz sources that are amplified to as much as 250 mW using power amplifiers developed for the Herschel Space Observatory. The frequency is then tripled using a novel waveguide GaAs Schottky diode frequency tripler. This planar diode produces 26 mW at 318 GHz. Peak conversion efficiency is over 15 percent, and the measured bandwidth of about 265 - 30 GHz is limited more by the driving source than by the tripler itself. This innovation is based on an integrated circuit designed originally for a single-chip 260- to 340-GHz balanced tripler. The power-combined version has two mirror-image tripler chips that are power-combined in-phase in a single waveguide block using a compact Y-junction divider at the input waveguide, and a Y-junction combiner at the output waveguide. The tripler uses a split-block waveguide design with two independent DC bias lines.

Maestrini, Alain↗

NASA NTRS2006

A 260-340 GHz Dual Chip Frequency Tripler for THz Frequency Multiplier Chains

We designed and fabricated a fix-tuned balanced frequency tripler working in the 260-340 GHz band to be the first stage of a x3x3x3 multiplier chain to 2.7 THz. The design of a dual-chip version of this multiplier featuring an input splitter / output combiner as part of the input / output matching networks of both chips - with no degradation of the expected bandwidth and efficiency- will be presented.

Schottky diodes↗

NASA NTRS2006

A High Efficiency Multiple-Anode 260-340 GHz Frequency Tripler

We report on the fabrication at the Jet Propulsion Laboratory of a fixed-tuned split-block waveguide balanced frequency tripler working in the 260-340 GHz band. This tripler will be the first stage of a x3x3x3 multiplier chain to 2.7 THz (the last stages of which are being fabricated at JPL) and is therefore optimized for high power operation. The multiplier features six GaAs Schottky planar diodes in a balanced configuration integrated on a GaAs membrane. Special attention was put on splitting the input power as evenly as possible among the diodes in order to ensure that no diode is overdriven. Preliminary RF tests indicate that the multiplier covers the expected bandwidth and that the efficiency is in the range 1.5-7.5 % with 100 mW of input power.

local oscillators↗

NASA NTRS2005

Local oscillator chain for 1.55 to 1.75 THz with 100-(mu)W peak power

We report on the design and performance of a fix-tuned x2x 3x 3 frequency multiplier chain that covers 1.55-1.75 THz. The chain is nominally pumped with 100 mW at W-band. At 120 K the measured output power is larger than 4 (mu)W across the band with a peak power of 100 (mu) W at 1.665 THz. A similar chain operated at room temperature produced a peak power of 21 (mu)W. These power levels now make it possible to deploy multipixel heterodyne imaging arrays in this frequency range.

frequency multiplier↗

NASA NTRS2005

A 540-640-GHz High-efficiency Four-anode Frequency Tripler

We report on the design and performance of a broad-band, high-power 540-640-GHz fix-tuned balanced frequency tripler chip that utilizes four planar Schottky anodes. The suspended strip-line circuit is fabricated with a 12-micron-thick support frame and is mounted in a split waveguide block. The chip is supported by thick beam leads that are also used to provide precise RF grounding. At room temperature, the tripler delivers 0.9-1.8 mW across the band with an estimated efficiency of 4.5%-9%. When cooled to 120 K, the tripler provides 2.0-4.2 mW across the band with an estimated efficiency of 8%-12%.

balanced triplers↗

NASA NTRS2005

Multi-Anode Frequency Triplers at Sub-Millimeter Wavelengths

We report on the design methodology of fix-tuned split-block waveguide balanced frequency triplers working at 300,600 and 900 GHz. They feature four to six GaAs Schottky planar diodes in a balanced configuration. A 6-anode 300 GHz tripler, a 6-anode 560 GHz tripler and a 4-anode 900 GHz tripler will be fabricated with JPL membrane technology in order to minimize dielectric loading and ensure accurate thickness of the substrate. A 4-anode 600 GHz tripler was fabricated with JPL substrateless technology that delivers 0.8-1.6mW in the 540-640 GHz band at room temperature. When cooled to l2OK this tripler delivers 2-4mW from 540 to 640 GHz.

Schottky diodes↗

NASA NTRS2004

Design of a Wideband 900 GHz Balanced Frequency Tripler for Radioastronomy

We report on the design of a fix-tuned split-block waveguide balanced frequency tripler working nominally at 900GHz. It uses a GaAs Schottky planar diode pair in a balanced configuration. The circuit will be fabricated with JPL membrane technology in order to minimize dielectric loading. The multiplier is bias-less to dramatically ease the mounting and the operating procedure. At room temperature, the expected output power is 50- 130 (micro)W in the band 800-970 GHz when the tripler is pumped with 4mW. By modifying the waveguide input and output matching circuit, the multiplier can be tuned to operate at lower frequencies.

Schottky diode multipliers↗