Engineering Papers⌕ Search

Engineering topics

Maddalon, D. V.

Publications and source records attributed to Maddalon, D. V..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Laminar flow flight experiments - A review

A development history is presented for flight tests of flow-laminarizing technologies, from the wooden-structure wing glove used with the B-18 of about 1940 to the X-21 of 1963-1965 and the wing incidence-varying tests conducted with gloved-wing F-111 and F-14 variable-sweep aircraft in more recent years. Natural laminar flight control testing has also been conducted with a B 757 airliner. Over the years, increasing attention has been given to the treatment of the leading edge of laminar flow wings in order to prevent flow instabilities that precipitate flow transition to turbulence farther aft.

Wagner, R. D.↗
NASA NTRS1990

Measurement of crossflow vortices, attachment-line flow, and transition using microthin hot films

A flow diagnostic experiment was conducted on a 45-deg swept-wing model using surface-mounted, multielement, microthin, hot-film sensors. The cross-flow vortex spacing, the attachment-line flow characteristics, and the transition region were all determined using an advanced data acquisition and instrumentation system. In addition to the frequencies of traveling waves predicted by linear stability theory, amplified disturbances at much higher frequencies were observed. Simultaneous measurements from sensors located at a number of chord and span locations highlighted the strong three-dimensionality of the boundary-layer flow in the presence of cross-flow vortices. The state of the attachment-line boundary layer was determined using a multielement sensor wrapped around the wing leading edge. The transition region flow characteristics were also identified.

Mangalam, S. M.↗
NASA NTRS1990

Applied aspects of laminar-flow technology

An account is given of the development status and performance levels achieved with natural laminar flow (NLF), extended wing chord laminar flow control (LFC), and hybrid laminar flow control (HLFC) concepts combining NLF and partial-chord LFC in the leading-edge region. Attention is given to NLF wing structure construction methods capable of achieving the requisite surface-irregularity tolerances, LFC through wing surface suction slots or perforated skins, and the deleterious effects of insects, ice crystals, and noise disturbance inputs on the ability of NLF, LFC, and HLFC wings to maintain effective laminar flow operation.

Braslow, A. L.↗
NASA NTRS1989

Transition flight experiments on a swept wing with suction

Flight boundary-layer transition experiments were conducted on a 30-degree swept wing with a perforated leading-edge suction panel. The transition location on the panel was changed by systematically varying the location and amount of suction. Transition from laminar to turbulent flow was due to leading-edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth, depending on flight condition and suction variation. Amplification factor correlations with transition location were made for various suction configurations using a state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility.

Maddalon, D. V.↗
NASA NTRS1989

Transition flight experiments on a swept wing with suction

Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth, depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Maddalon, D. V.↗
NASA NTRS1989

Transition Flight Experiments on a Swept Wing with Suction

Flight boundary-layer transition experiments were conducted on a 30 degree swept wing with a perforated leading-edge suction panel. The transition location on the panel was changed by systematically varying the location and amount of suction. Transition from laminar to turbulent flow was due to leading-edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth, depending on flight condition and suction variation. Amplification factor correlations with transition location were made for various suction configurations using a state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility.

Maddalon, D. V.↗
NASA NTRS1989

Transition Flight Experiments on a Swept Wing With Suction

Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth-depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Maddalon, D. V.↗
NASA NTRS1988

Laminar flow control leading edge systems in simulated airline service

The feasibility of two candidate leading-edge flow laminarization systems applicable to airline service was tested using representative airline operational conditions with respect to air traffic, weather, and airport insect infestation. One of the systems involved a perforated Ti alloy suction surface with about 1 million 0.0025-in. diameter holes drilled by electron beam, as well as a Krueger-type flap that offered protective shielding against insect impingement; the other supplied surface suction through a slotted Ti alloy skin with 27 spanwise slots on the upper and lower surface.

Wagner, R. D.↗
NASA NTRS1988

Fifty years of laminar flow flight testing

Laminar flow flight experiments conducted over the past 50 years are reviewed. The emphasis is on flight testing conducted under the NASA Laminar Flow Control Program, which has been directed towards the most challenging technology application, the high-subsonic-speed transport. The F111/TACT NLF Glove Flight Test, the F-14 Variable-Sweep Transition Flight Experiment, the 757 Wing-Noise Survey and NLF Glove Flight Test, the NASA Jetstar Leading-Edge Flight Test Program, and the recently initiated Hybrid Laminar-Flow-Control Flight Experiment are discussed.

Wagner, R. D.↗
NASA NTRS1988

Laminar Flow Control Leading Edge Systems in Simulated Airline Service

Achieving laminar flow on the wings of a commercial transport involves difficult problems associated with the wing leading edge. The NASA Leading Edge Flight Test Program has made major progress toward the solution of these problems. The effectiveness and practicality of candidate laminar flow leading edge systems were proven under representative airline service conditions. This was accomplished in a series of simulated airline service flights by modifying a JetStar aircraft with laminar flow leading edge systems and operating it out of three commercial airports in the United States. The aircraft was operated as an airliner would under actual air traffic conditions, in bad weather, and in insect infested environments.

Wagner, R. D.↗
NASA NTRS1986

Design and fabrication of large suction panels with perforated surfaces for laminar flow control testing in a transonic wind tunnel

Considerable progress has been made in the development of perforated suction surface material for laminar flow control applications. Electron-beam perforated titaniuum skin was used as the suction surface. Critical issues related to suction panel manufacturing were identified and largely resolved. The final product included fabrication of a 7-foot chord by 7-foot span perforated laminar flow control wind tunnel model. Techniques used can be adapted to modern aircraft production lines. The report includes details on panel instrumentation and other features required for testing in a transonic pressure tunnel.

Maddalon, D. V.↗
NASA NTRS1984

Technology developments for laminar boundary layer control on subsonic transport aircraft

The development of laminar flow technology for commercial transport aircraft is discussed and illustrated in a review of studies undertaken in the NASA Aircraft Energy Efficiency (ACEE) program since 1976. The early history of laminar flow control (LFC) techniques and natural laminar flow (NLF) airfoil designs is traced, and the aims of ACEE are outlined. The application of slotted structures, composites, and electron beam perforated metals in supercritical LFC airfoils, wing panels, and leading edge systems is examined; wind tunnel and flight test results are summarized; studies of high altitude ice effects are described; and hybrid (LFC/NLF designs are characterized. Drawings and photographs are provided.

Wagner, R. D.↗
NASA NTRS1984

Technology developments for laminar boundary layer control on subsonic transport aircraft

An overview of laminar flow control (LFC) technology developments is presented, along with a description of NASA's broadened program concerning laminar flow concepts for commercial transports. Topics covered include developments in LFC airfoils, wing surface panels, and leading-edge systems, as well as the effects of high altitude ice particles and insect impacts. It is suggested that the electron beam perforated titanium surface is superior to the Dynapore surface. The Douglas LFC wing design, the Krueger flap, the Lockheed, and the Douglas leading-edge concepts are covered. Future research includes an evaluation of a hybrid LFC concept, which combines LFC suction in the leading-edge region with natural laminar flow over the wing box.

Wagner, R. D.↗
NASA NTRS1984

Technology developments for laminar boundary layer control on subsonic transport aircraft

The development of laminar-flow technology for commercial transport aircraft is discussed and illustrated in a review of studies undertaken in the NASA Aircraft Energy Efficiency (ACEE) program since 1976. The early history of laminar-flow-control (LFC) techniques and natural-laminar-flow (NLF) airfoil designs is traced, and the aims of ACEE are outlined. The application of slotted structures, composites, and electron-beam-perforated metals in supercritical LFC airfoils, wing panels, and leading-edge systems is examined; wind-tunnel and flight test results are summarized; studies of high-altitude ice effects are described; and hybrid LFC/NLF designs are characterized. Drawings and photographs are provided.

Wagner, R. D.↗
NASA NTRS1984

Airframe technology for aircraft energy efficiency

The economic factors that resulted in the implementation of the aircraft energy efficiency program (ACEE) are reviewed and airframe technology elements including content, progress, applications, and future direction are discussed. The program includes the development of laminar flow systems, advanced aerodynamics, active controls, and composite structures.

James, R. L., Jr.↗
NASA NTRS1984

The drive for Aircraft Energy Efficiency

NASA's Aircraft Energy Efficiency (ACEE) program, which began in 1976, has mounted a development effort in four major transport aircraft technology fields: laminar flow systems, advanced aerodynamics, flight controls, and composite structures. ACEE has explored two basic methods for achieving drag-reducing boundary layer laminarization: the use of suction through the wing structure (via slots or perforations) to remove boundary layer turbulence, and the encouragement of natural laminar flow maintenance through refined design practices. Wind tunnel tests have been conducted for wide bodied aircraft equipped with high aspect ratio supercritical wings and winglets. Maneuver load control and pitch-active stability augmentation control systems reduce fuel consumption by reducing the drag associated with high aircraft stability margins. Composite structures yield lighter airframes that in turn call for smaller wing and empennage areas, reducing induced drag for a given payload. In combination, all four areas of development are expected to yield a fuel consumption reduction of 40 percent.

James, R. L., Jr.↗
NASA NTRS1983

Effect of surface waviness on a supercritical laminar-flow-control airfoil

Calculations were made of the effects of surface waviness on the external pressure of a supercritical airfoil at design conditions. Wave parameters varied include amplitude, wavelength, phase, and number of cycles. Effects of single and multiple waves are calculated at various chordwise locations. General trends of surface waviness effects on pressure distribution are determined and these solutions are reported. Contour deviations are imposed on the upper surface of the airfoil. Results are presented in a manner designed to facilitate ready comparison with the ideal contour static pressure distribution.

Maddalon, D. V.↗