Engineering Papers⌕ Search

Engineering topics

Ma, Haitao

Publications and source records attributed to Ma, Haitao.

Effect of Ag3Sn nanoparticles and temperature on Cu6Sn5 IMC growth in Sn-xAg/Cu solder joints

Highlights: • The number density of Ag{sub 3}Sn grains precipitated upon Cu{sub 6}Sn{sub 5}, increases with Ag content and reflow temperature (T). • Raising of wt. % of Ag in solder and lowering of T can cause an increase in grain diameter of Ag{sub 3}Sn nanoparticles. • The blockading effect of Ag{sub 3}Sn particles on Cu{sub 6}Sn{sub 5} IMC growth is more pronounced in Sn-3Ag and Sn-3.5Ag alloys. • IMC suppressing nanoparticles can be utilized for solder materials design. - Abstract: The growing importance of Pb-free Sn-xAg solders and high cost of Ag has attracted the attention of researchers to perform experiment with solders with varied content of Ag element. In this study, Sn-xAg(0,1,2,3.5) solder balls on Cu substrate have been reflowed at 250/275/300 °C for 60 s and air cooled. Finite element method has been utilized to simulate the concentration and temperature during cooling. The experimental results suggest that the Cu flux through grain boundary diffusion is the dominant mechanism for Cu{sub 6}Sn{sub 5} intermetallic compound growth in Pure Sn and Sn-1Ag solders. When the Ag content is increased, as in case of Sn-3Ag and Sn-3.5Ag alloys; the shielding effect of Ag{sub 3}Sn nanoparticles is the determinant factor for affecting the thickness of Cu{sub 6}Sn{sub 5} IMC. Both Cu influx rate and shielding effect of Ag{sub 3}Sn nanoparticles are enhanced with the raise in pre-cooled isothermal reflow temperature. Sn-1Ag solder is observed to have the thickest Cu{sub 6}Sn{sub 5} IMC.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In situ study on the effect of thermomigration on intermetallic compounds growth in liquid-solid interfacial reaction

Synchrotron radiation real-time imaging technology was carried out in situ to observe and characterize the effect of thermomigration on the growth behavior of interfacial intermetallic compounds (IMCs) in Cu/Sn/Cu solder joint during soldering. The thermomigration resulted in asymmetrical formation and growth of the interfacial IMCs. Cu{sub 6}Sn{sub 5} and Cu{sub 3}Sn IMCs formed at the cold end and grew rapidly during the whole soldering process. However, only Cu{sub 6}Sn{sub 5} IMC formed at the hot end and remained relatively thin until solidification. The IMCs at the cold end were nearly seven times thicker than that at the hot end after solidification. The Cu dissolution at the cold end was significantly restrained, while that at the hot end was promoted, which supplied Cu atoms to diffuse toward the cold end under thermomigration to feed the rapid IMC growth. Moreover, the thermomigration also caused asymmetrical morphology of the interfacial IMCs at the cooling stage, i.e., the Cu{sub 6}Sn{sub 5} IMC at the cold end transformed into facet structure, while that at the hot end remained scallop-type. The asymmetrical growth behavior of the interfacial IMCs was analyzed from the view point of kinetics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Type Ia supernovae : advances in large scale simulation.

There are two principal scientific objectives in the study of Type Ia supernovae - first, a better understanding of these complex explosions from as near first principles as possible, and second, enabling the more accurate utilization of their emission to measure distances in cosmology. Both tasks lend themselves to large scale numerical simulation, yet take us beyond the current frontiers in astrophysics, combustion science, and radiation transport. Their study requires novel approaches and the creation of new, highly scalable codes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗