Engineering Papers⌕ Search

Engineering topics

Lupu, N.

Publications and source records attributed to Lupu, N..

The New Small Wheel electronics

The increase in luminosity, and consequent higher backgrounds, of the LHC upgrades require improved rejection of fake tracks in the forward region of the ATLAS Muon Spectrometer. The New Small Wheel upgrade of the Muon Spectrometer aims to reduce the large background of fake triggers from track segments that don't originate from the interaction point. The New Small Wheel employs two detector technologies, the resistive strip Micromegas detectors and the “small” Thin Gap Chambers, with a total of 2.45 million electrodes to be sensed. The two technologies require the design of a complex electronics system given that it consists of two different detector technologies and is required to provide both precision readout and a fast trigger. It will operate in a high background radiation region up to about 20 kHz/cm 2 at the expected HL-LHC luminosity of $\mathcal{L}$= 7.5 × 10 34 cm -2 s -1 . The architecture of the system is strongly defined by the GBTx data aggregation ASIC, the newly-introduced FELIX data router and the software based data handler of the ATLAS detector. The electronics complex of this new detector was designed and developed in the last ten years and consists of multiple radiation tolerant Application Specific Integrated Circuits, multiple front-end boards, dense boards with FPGA's and purpose-built Trigger Processor boards within the ATCA standard. The New Small Wheel has been installed in 2021 and is undergoing integration within ATLAS for LHC Run 3. It should operate through the end of Run 4 (December 2032). In this manuscript, the overall design of the New Small Wheel electronics is presented.

47 OTHER INSTRUMENTATION↗

Tailoring the magnetic properties of new Fe-Ni-Co-Al-(Ta,Nb)-B superelastic rapidly quenched microwires

Ferromagnetic Fe-Ni-Co-Al-(Ta,Nb)-B microwires with diameters from 170 μm to 50 μm, which possess both superelastic and good magnetic properties, have been prepared by rapid quenching from the melt using the in rotating water spinning technique followed by cold-drawing and ageing. The cold-drawing and annealing processes lead to the initialization of premartensitic phases as confirmed by the X-ray diffraction and scanning transmission electron microscopic investigations, more significantly in the 50 μm cold-drawn microwires. An increase in the coercive field and in the saturation magnetization has been obtained by annealing, more importantly in the case of Nb-containing alloy. Ageing by thermal or current annealing led to the initialization of the superelastic effect. High values of strain of up to 1.8%, very good repeatability under successive loading, and values of superelastic effect of up to 1.2% have been achieved. The structural analysis coupled with the stress-strain data suggests that these materials annealed at 800 °C have superelastic potential at reduced ageing times. The magnetic behavior was found to be easily tailored through both thermal and thermomagnetic treatments with changes in the magnetic parameters which can be contactless detected. The results are important for future applications where both mechanical and magnetic properties matter, i.e., sensing/actuating systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The emergence of magnetic properties in (Pb{sub 0.845}Sm{sub 0.08}Fe{sub 0.035})(Ti{sub 0.98}Mn{sub 0.02})O{sub 3} and (Pb{sub 0.88}Nd{sub 0.08})(Ti{sub 0.98}Mn{sub 0.02})O{sub 3} perovskite ceramics

The emergence of magnetic properties and quadratic magnetoelectric coupling in a material with outstanding ferroelectric properties has been pursued. Thus, the multiferroicity driven by the substitution of rare earth R{sup 3+} ions (R = Sm, Nd) on the A-site of PbTiO{sub 3} perovskite ceramics has been investigated. In some samples, a transition element with large ionic radius, like Fe{sup 2+}, has been also added on the A site. Polycrystalline ceramic samples with composition (Pb{sub 1-3x/2-y}R{sub x}Fe{sub y}) (Ti{sub 0.98}Mn{sub 0.02})O{sub 3} (R = Sm; x = 0.08, y = 0.035) and (Pb{sub 1−3x/2}R{sub x})(Ti{sub 0.98}Mn{sub 0.02})O{sub 3} (R = Nd, x = 0.08) have been prepared by conventional solid state ceramic processing, starting from reagent grade oxide powders. X-ray diffraction analysis confirmed the obtaining of a crystalline phase with tetragonal P4 mm symmetry. Transmission electron microscopy and high resolution transmission electron microscopy investigations have been carried out in order to analyze the local structure. Temperature dependence of dielectric permittivity revealed a strong anomaly at the temperature T{sub c} of the paraelectric-ferroelectric phase transition. Transition temperature values depend on the R ion type and are lower than in pure lead titanate by 80–100 K. A broad anomaly of dielectric permittivity is found below 140–180 K, where magnetization also increases due to the quadratic magnetoelectric coupling between ferroelectric and magnetic states. For the (Pb{sub 0.845}Sm{sub 0.08}Fe{sub 0.035})(Ti{sub 0.98}Mn{sub 0.02})O{sub 3} composition, the piezoelectric charge coefficient at room temperature was d{sub 31} ∼−6.5 pC/N and the remanent magnetization M{sub r} at room temperature was about 0.1 emu/g.

36 MATERIALS SCIENCE↗