Engineering Papers⌕ Search

Engineering topics

Lunsford, R.

Publications and source records attributed to Lunsford, R..

At least 37 records · Page 2

Plasma Facing Component Characterization and Correlation With Plasma Conditions in Lithium Tokamak Experiment-β

Lithium coatings in the Lithium Tokamak eXperiment (LTX) led to flat temperature profiles. The flat temperature profiles were observed along with a hot, low density edge, implying a broad, collisionless scrape-off layer (SOL). Additionally, in vacuo X-ray photoelectron spectroscopy (XPS) measurements established that lithium coatings evaporatively deposited onto high-Z plasma facing components (PFCs) became oxidized while retaining the ability to achieve good plasma performance long after lithium was applied to the PFCs. Longstanding theory predicted flat temperature profiles with low recycling walls, which was presumed to be due to hydrogen binding with elemental lithium to form lithium hydride. The presence of oxidized lithium, however, raised questions regarding the exact mechanism of hydrogen retention in LTX. To investigate these questions, the upgraded facility LTX- β includes a new sample exposure probe (SEP) for more detailed in vacuo analysis of PFC samples. The SEP is equipped with a vacuum suitcase capable of transporting samples representative of the LTX- β outer midplane PFCs to a stand-alone XPS system while maintaining pressures lower than the LTX- β base vacuum to limit the contamination between sample exposure and analysis. The low-energy resolution XPS system used in past experiments could only enable the determination of elemental percentages on the PFC sample surfaces. Because the new XPS system has higher energy resolution, it is more direct to assign chemical compounds to the measured binding energies. This capability has been confirmed by comparing XPS data from PFC test samples with measurements using a commercial high-resolution XPS system. Quartz crystal microbalances (QCMs) were used to quantify the thickness of the deposited lithium on the LTX- β PFCs. This article describes the application of the SEP to characterize the PFC surfaces using XPS and their relationship to plasma conditions.

Maan, Anurag↗

Shattered pellet penetration in low and high energy plasmas on DIII-D

Shattered Pellet Injection (SPI) was previously adopted as the baseline disruption mitigation system for ITER, as the radiative payload penetration into DIII-D plasmas from SPI is superior to those using the Massive Gas Injection (MGI) method. Because of the substantial differences in the energy content of ITER plasma and those in present experiments, reliable 3d MHD modeling, benchmarked against present experiments is needed to project to ITER plasmas. On account of these needs, the depth of SPI fragment penetration in DIII-D plasmas was investigated by injecting SPI into two discharges with vastly different energy content and pedestal height. 400 Torr-L pure Ne fragmented pellets at a velocity of about 200 m s -1 were injected into a 0.2 MJ L-mode discharge and a 2 MJ super H-mode discharge. Results show deep penetration of SPI fragments into low-energy plasmas in DIII-D. SPI fragment penetration is reduced as the plasma energy content increases, with some discharges exhibiting penetration that is confined to the outer regions of the plasma. The injected SPI fragments are also spread out over a distance of about 20 cm, which results in some fragments arriving near the end of or after the thermal quench is over.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Full-torus impurity transport simulation for optimizing plasma discharge operation using a multi-species impurity powder dropper in the large helical device

The transport of impurities supplied by a multi-species impurity powder dropper (IPD) in the large helical device (LHD) is investigated using a three-dimensional peripheral plasma fluid code (EMC3-EIRENE) coupled with a dust transport simulation code (DUSTT). The trajectories of impurity powder particles (Boron, Carbon, Iron, and Tungsten) dropped from the IPD and the impurity transport in the peripheral plasma are studied in a full-torus geometry. The simulation reveals an appropriate size of the impurity powder particles and an optimum operational range of the dust drop rates for investigating the impurity transport without inducing radiation collapse. The simulation also predicts a favourable plasma discharge condition for wall conditioning (boronization) using the IPD in order to deposit boron to high plasma flux and neutral particle density areas in the divertor region in the inboard side of the torus.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Active conditioning of ASDEX Upgrade tungsten plasma-facing components and discharge enhancement through boron and boron nitride particulate injection

The injection of boron (B) and boron nitride (BN) powders into ASDEX Upgrade H-mode discharges have demonstrated effective control of tungsten influx in low density/collisionality operational regimes, similar to conventional boronization methods. Sub-mm powder particles are gravitationally accelerated into the upper edge of a lower single null H-mode plasma with a boundary shape roughly conforming to the shape of the poloidal midplane limiters. Visible spectroscopy measurements at one of the outer limiter showed increases in both B and N signal levels, as well as elevated B levels in the divertor, and an increase in total radiated power by greater than a factor of two during BN injection. Globally the BN injection improved energy confinement by 10%–20%, associated with improvements in pedestal performance similar to gaseous N injection. Following conditioning discharges with B powder injection, three low gas-fueling discharges with magnetic perturbations for ELM suppression were successfully conducted. Furthermore, these first results suggest that the application of B containing powders can be used to both improve plasma performance in real-time, and to improve overall wall conditions for subsequent discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ablation of solid pellets induced by supra-thermal ions in the far scrape-off layer of tokamak plasmas

Injection of solid pellets is a key element in several aspects of the operation of a magnetic confinement plasma reactor for fusion applications, including plasma fueling, control and diagnosis. This letter reports observations demonstrating that pellet ablation can begin outside the plasma boundary, by effect of supra-thermal ions, whose orbits, under appropriate conditions, can extend well into the vacuum region. The phenomenon was recorded during plasma discharges in the DIII-D tokamak, combining pulsed modulation of heating neutral beams, with high-frequency injection of sub-millimeter lithium pellets, and it is ascribed to the large fraction of trapped beam ions associated with counter current neutral beam injection. The effect was quantitatively evaluated by means of Monte-Carlo simulations of supra-thermal ion orbits, finding that the heat-deposition was of the order of 50-100 W/mm 2 , in the region traversed by the lithium pellets before reaching the plasma boundary, which is consistent with the severe pellet deterioration observed for low velocity pellets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time wall conditioning by controlled injection of boron and boron nitride powder in full tungsten wall ASDEX Upgrade

In ASDEX Upgrade with full-tungsten wall, boronization is an important tool to control tungsten sources and allow reliable operation at low collisionality. The duration of the beneficial effects is limited by the erosion of the boron layer, in particular on the tungsten ion-cyclotron antenna limiters. We report results from experiments exploring injection boron-rich powders in tokamak plasmas as a way to replenish boron coating and extend the lifetime of boronization effects. Pure boron and boron nitride powders were introduced gravitationally in plasma discharges at rates up to 60 mg/s for durations up to 3 s. Boron injection with cumulative amounts >100 mg appeared to improve wall conditions similarly to boronization, with indications of reduced influx of oxygen and tungsten from the antenna limiter. Moreover, cumulative injection of 340 mg of B appeared sufficient to enable successful execution of low collisionality scenarios critically relying on freshly boronized walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A horizontal powder injector for W7-X

We report that injection of low-Z powders into fusion plasma has been used to improve wall conditions, similar to the standard boronization process using diborane. Powder injection has the advantage of being much simpler, non-toxic, and efficient. The W7-X stellarator is planning on utilizing powder injection in long pulse discharges; a proof-of-principle test for horizontal injection into the plasma was conceived, a Probe Mounted Particle Injector (PMPI). The PMPI concept is developed using a polyetheretherketone (PEEK) paddle wheel hub that is driven by a piezo motor, due to the high magnetic fields, that rotates at 100 deg/s. This small PMPI fits into an envelope of 120 mm diameter × 150 mm long, a standard size for Multi-Purpose Manipulator (MPM). The device is housed in a carbon cup mounted on a retractable probe that can be placed near the plasma edge, enabling powder injection ˜4–8 cm radially into the boundary plasma. The feed for the paddle is via piezo electric actuator that vibrates a funnel filled with powder into a trough for the paddle to push. The 8 paddle arms, 35 mm long and 10 mm wide, are made from 0.38 mm thick PEEK which drag slightly along the powder-filled trough bottom, becoming a spring-loaded paddle which accelerates the powder upon release. Finally, design challenges are the high ambient magnetic field, vacuum compatible materials, high temperature environment, limited rotary-drive options, and compact space. The design and testing of this new device will be presented.

36 MATERIALS SCIENCE↗

Results from an improved flowing liquid lithium limiter with increased flow uniformity in high power plasmas in EAST

Significant engineering and physic progress was made by the upgrade of a flowing liquid lithium limiter (FLiLi) inserted into EAST H-mode discharges in 2016. The progress includes an improvement of liquid Li coverage uniformity, no macroscopic surface erosion by plasma materials interaction, effective removal of 55% of the discharge heat flux using high pressure He cooling during ohmic discharges, and the demonstrated ability to restart Li flow for a second experiment performed a week after the first. With increasing Li flow rate, fuel particle recycling and Fe impurity radiation gradually decreased, and plasma performance slightly improved, but there was no impact on the edge tungsten influx. No obvious Li bursts appeared during operation with up to about 4.5 MW auxiliary heating power with peak heat flux reaching ~4 MW m –2 on FLiLi. In addition, a gradual mitigation of edge localized mode (ELM) activity was observed with FLiLi operation. Lastly, short-lived ELM-free phases were observed for the first time in EAST during FLiLi insertion, with increasing τ E and transient H 98(y, 2) < 2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A multi-species powder dropper for magnetic fusion applications

Here, we present a device for controlled injection of a variety of materials in powder form. The system implements four independent feeder units, arranged to share a single vertical drop tube. Each unit consists of a 80 ml reservoir, coupled to a horizontal linear trough, where a layer of powder is advanced by piezo-electric agitation at a speed proportional to the applied voltage, until it falls into a drop tube. The dropper has been tested with a number of impurities of low (B, BN, C), intermediate (Si, SiC), and high Z (Sn) and a variety of microscopic structures (flakes, spheres, rocks) and sizes (5-200 μm). For low Z materials, drop rates ~2-200 mg/s have been obtained showing good repeatability and uniformity. A calibrated light-emitting diode (LED)-based flowmeter allows measuring and monitoring the drop rate during operation. The fast time-response of the four feeders allows combination of steady and pulsed injections, providing a flexible tool for controlled-dose, real-time impurity injection in fusion plasmas.

47 OTHER INSTRUMENTATION↗

ELM frequency enhancement and discharge modification through lithium granule injection into EAST H-modes

The injection of impurity granules into fusion research discharges can serve as a catalyst for ELM events. For sufficiently low ELM frequencies, and granule sizes above a threshold, this can result in full control of the ELM cycle, referred to as ELM pacing. For this research, we extend the investigation to conditions where the natural ELM frequency is too high for ELM pacing to be realized. Utilizing multiple sizes of lithium granules and classifying their effects by granule size, we demonstrate that ELM mitigation through frequency multiplication can be used at ELM triggering rates that nominally make ELM pacing unrealizable. We find that above a size threshold, injected granules promptly trigger ELMs and commensurately enhance the ELM frequency. Below this threshold size, injection of an individual granule does not always lead to the prompt triggering of an ELM; however, collective ablation in the edge pedestal region does enhance the ELM frequency. Furthermore, Li granules too small to individually trigger ELMs were injected into EAST H-mode discharges at frequencies up to 2.3 kHz; collectively the granules were observed to enhance the natural ELM frequency up to 620 Hz, resulting in a ~2.4 × multiplication of the natural ELM frequency and a 50% decrease of the ELM size.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time reduction of tungsten impurity influx using lithium powder injection in EAST

We report the first successful use of solid material injection, in powder form, to reduce core tungsten impurities in EAST discharges with tungsten divertor plasma-facing components. Tungsten is the leading plasma-facing material for use in ITER as well as future fusion devices. However, tungsten sometimes accumulates in the plasma core of fusion devices, which is an impediment to the achievement of high-power, long-pulse H-modes. In this work, tungsten impurity influx from the tungsten divertor was reduced by real-time injection of lithium powder into EAST discharges. An increase in stored energy and confinement accompanied the sharp reduction of core tungsten with real-time lithium powder injection in L-mode discharges. In H-mode discharges, real-time lithium powder injection reduced the tungsten core impurity emission while also mitigating ELMs. During powder injection, the divertor electron temperature was reduced, which reduced the tungsten source. In conclusion, the tungsten impurity emission remained low in discharges even after active lithium injection was terminated, a signature of improved and lasting wall conditioning in the tungsten divertor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A new developed in-between shots lithium evaporation coating system for improving plasma performance in EAST

A new in-between shots evaporative lithium coating system has been successfully developed and implemented on the Experimental Advanced Superconducting Tokamak (EAST) for the 2017 campaign. This paper describes a novel technique for the introduction of lithium into the EAST vessel allowing evaporative coatings to be applied between discharges without requiring a significant amount of time to insert and retract the lithium source. This newly designed system utilizes a rotating axis driven by a vacuum dynamic sealing feedthough under remote control to open and close a shutter. A compression bellows, which drives the delivery tube, guarantees accurate position of the oven thus avoiding possible direct contact with the plasma. This allows the new evaporation system to be operated in two distinct modes. One mode is operated in-between shots to refresh pre-coated lithium film, the other is a real-time lithium vapor injection during plasma operations to provide active wall conditioning during long pulse plasma discharges. In this paper, operation of this new lithium deposition system in the in-between shots replenishment mode is described. Initial experiments show that this system worked well during the interval of discharges in EAST, and the in-between shots lithium coating effectively reduced the wall recycling and impurity concentrations. Furthermore, the application of fresh lithium coating lead to sustain the plasma stored energy and confinement, as well as a reduction of impurity radiation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Quasi-Periodic Linear Feeder for the Impurity Granular Injection on DIII-D

Injection of solid nonfuel pellets has been actively used as a tool for pacing and mitigation of edge localized modes (ELMs). In DIII-D, effective ELM pacing has been demonstrated by the high-frequency injection of lithium and carbon submillimeter spheres, using the impurity granule injector (IGI). This device injects granules into the plasma at speeds up to 150 m/s, through impact with a rotating impeller. In the IGI, high-frequency granule delivery was accomplished through a vibrational granule dropper, in which high time-average rates are obtained at the cost of lack of period control. Here, we present a new in-line granule feeder, capable of delivering granules of size 0.2-2 mm with no restriction of material properties, at quasi-periodic rates of up to 150 Hz, for 0.7-mm diameter lithium granules (600 Hz using 0.3-mm granules). The new dropper mechanism combines two piezo-in-line units; one which feeds the impeller and one which circulates granules that are filtered out of the feeder path. A remotely adjustable filter eliminates granules that are stacked, oversized, or side by side allowing the formation of a single moving granule injection line. The granules fall off the in-line feeder exit one at a time, achieving a quasi-periodic delivery rate proportional to the exit speed. At higher rates, the periodicity deteriorates. This behavior was studied using high-speed cameras and electrostatic measurements, and it was found that at drop rates <60 Hz, the granule delivery period has a variation of ±25% which appears to be caused by gaps which develop in the last centimeter of the injection line, as granules exit off the moving track. The linear feeder concept is robust against bridge instabilities and clogging issues, thanks to the simple diverter filter and constant recirculation of granules. Furthermore, the open-top design of the device facilitates refilling the device from separate reservoirs and has easy access for directly monitoring operation and adjustment. This paper describes the details of the in-line feeder design, along with several design iterations. The goal is a robust in-vacuum mechanism that can deliver granule flow ranging from a single particle to a line of particles at 150 per second, using different sizes and materials from the same apparatus.

42 ENGINEERING↗

Active Recycling Control Through Lithium Injection in EAST

The coating of tokamak walls with thin layers of lithium has been demonstrated to reduce plasma recycling from the plasma-facing surfaces and to improve overall plasma performance. These effects, including reduced divertor D α emission, the elimination of edge-localized modes, and increased energy confinement have been observed in multiple experiments when lithium coatings are applied before plasma discharges. However, this coating technology does not extrapolate to future long-pulse devices, since the lithium coatings will be passivated by the continual plasma flux onto the surface. In order to provide active conditioning capability, a new technology has been developed that is capable of injecting lithium powder into the scrape-off layer plasma during plasma discharges, where it quickly liquefies and turns into an aerosol. The use of this “lithium dropper” is under study at the Experimental Advanced Superconducting Tokamak (EAST), where the potential benefits of real-time wall conditioning via lithium injection are being tested. Here, we present an analysis of the recycling characteristics during EAST experiments testing active lithium injection in order to assess recycling reduction and control. Lithium aerosol was injected from the top of the machine, with one system dropping lithium near the X-point and another into the low-field side divertor leg. The injection of lithium into the SOL reduced divertor recycling, as evidenced by reduced D α emission with ion flux measured by probes relatively unchanged. This effect is strongest in the active divertor, confirming the lithium is transported to strongly plasma-wetted areas. Furthermore, quantitative analysis of the recycling changes using the SOLPS edge plasma and neutral transport code indicated a ~20% reduction in recycling coefficient with lithium injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ELM elimination with Li powder injection in EAST discharges using the tungsten upper divertor

Here, we report the first successful use of lithium (Li) to eliminate edge-localized modes (ELMs) with tungsten divertor plasma-facing components in the EAST device. Li powder injected into the scrape-off layer of the tungsten upper divertor successfully eliminated ELMs for 3–5 s in EAST. The ELM elimination became progressively more effective in consecutive discharges at constant lithium delivery rates, and the divertor D α baseline emission was reduced, both signatures of improved wall conditioning. A modest decrease in stored energy and normalized energy confinement was also observed, but the confinement relative to H98 remained well above 1, extending the previous ELM elimination results via Li injection into the lower carbon divertor in EAST. These results can be compared with recent observations with lithium pellets in ASDEX-Upgrade that failed to mitigate ELMs, highlighting one comparative advantage of continuous powder injection for real-time ELM elimination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Injected mass deposition thresholds for lithium granule instigated triggering of edge localized modes on EAST

The ability of an injected lithium granule to promptly trigger an edge localized mode (ELM) has been established in multiple experiments. By horizontally injecting granules ranging in diameter from 200 microns to 1mm in diameter into the low field side of EAST H-mode discharges we have determined that granules with diameter > 600 microns are successful in triggering ELMs more than 95% of the time. Granules were radially injected from the outer midplane with velocities ~ 80 m/s into EAST upper-single null discharges with an ITER like tungsten monoblock divertor. ELM triggering was a prompt response to granule injection, and for granules of a sufficient size there was no evidence of a "trigger lag" phenomenon as observed in full metal machines. We also demonstrated that the triggering efficiency decreased with granule size during dynamic size scans. These granules were individually tracked throughout their injection cycle in order to determine their efficacy at triggering an ELM. Furthermore, by simulating the granule injection with an experimentally benchmarked neutral gas shielding (NGS) model, the ablatant mass deposition required to promptly trigger an ELM is calculated and the fractional mass deposition is determined. Simulated 900 micron granules capable of triggering an ELM show a peaked mass deposition of 3.9 x 10 17 atoms per mm of penetration at a depth of approximately 5 cm past the separatrix.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗