Engineering topics

Luckring, J. M.

Publications and source records attributed to Luckring, J. M..

29 records · Page 2

NASA NTRS1983

Evaluation of factors determining the accuracy of linearized subsonic panel methods

A systematic evaluation of the factors determining the accuracy of linearized subsonic panel methods is presented. In particular, the constant and quadratically varying doublet panel methods are compared for thin and thick surface modelings in two and three dimensions. The sensitivity of results to panel edge and control point locations is studied for both of the methods. The first order convergence of the quadratic doublet method near network edges and the subsequent effect on the Kutta condition is investigated. Results from a quadratic doublet method specifically designed for a vector processing computer are shown.

Thomas, J. L.↗

NASA NTRS1982

Recent advances in applying Free Vortex Sheet theory to the estimation of vortex flow aerodynamics

Free Vortex Sheet theory has been applied to a variety of configurations for the estimation of three-dimensional pressure distributions for wings developing separation-induced leading-edge vortex flows. Correlations with experiment show reasonable estimates for the effects of compressibility, side-slip, side edges, swept-wing blast-induced loads, and leading-edge vortex flaps. Theoretical studies expand upon these correlations to show general aerodynamic trends. Consideration is also given to simple, yet effective techniques which expedite convergence and therefore reduce computational expense.

Luckring, J. M.↗

NASA NTRS1979

Flow visualization studies of a general research fighter model employing a strake-wing concept at subsonic speeds

A systematic wind tunnel study was conducted in the Langley high-speed 7 by 10 foot tunnel to document, by oil-flow photographs, the surface flow patterns for configurations incorporating strake-wing geometries indicative of current and proposed maneuvering aircraft. The configurations employed combinations of strakes with reflexed planforms having exposed spans of 10 percent, 20 percent, and 30 percent of the reference wing span and wings with trapezoidal planforms having leading-edge sweep angles of approximately 30 deg, 44 deg, and 60 deg. Tests were conducted at Mach numbers of 0.3 and 0.5 and at angles of attack ranging from approximately 5 deg to 30 deg in 5 deg increments at 0 deg sideslip. The configurations incorporating the strake-wing geometries exhibited more organized flow patterns with smaller asymmetries to higher angles of attack than the corresponding configurations incorporating the wing-alone geometries did.

Luckring, J. M.↗

NASA NTRS1979

Subsonic longitudinal and lateral aerodynamic characteristics for a systematic series of strake-wing configurations

A systematic wind tunnel study was conducted in the Langley 7 by 10 foot high speed tunnel to help establish a parametric data base of the longitudinal and lateral aerodynamic characteristics for configurations incorporating strake-wing geometries indicative of current and proposed maneuvering aircraft. The configurations employed combinations of strakes with reflexed planforms having exposed spans of 10%, 20%, and 30% of the reference wing span and wings with trapezoidal planforms having leading edge sweep angles of approximately 30, 40, 44, 50, and 60 deg. Tests were conducted at Mach numbers ranging from 0.3 to 0.8 and at angles of attack from approximately -4 to 48 deg at zero sideslip.

Luckring, J. M.↗

NASA NTRS1979

Recent theoretical developments and experimental studies pertinent to vortex flow aerodynamics, with a view towards design

Recent progress in a research program directed toward an improved vortex flow technology base was reviewed. Analysis methods for conical flow and analysis and design methods for nonconical flows are presented. Applications are made for a variety of planar, nonplanar, and interferring lifting surfaces. Several methods are shown to provide reasonable estimates of over-all forces and moments for simple wing planforms with the suction analogy method currently offering the most versatility for arbitrary configuration applications. For the prediction of surface loadings the free vortex sheet method being developed by Boeing is shown to have considerable promise and further development of this type of method is encouraged. A data base for ogee strake-wing configurations is summarized with an emphasis on the requirements for maximizing the interference lift. A strake planform design procedure is discussed and a first solution (gothic in planview) is integrated with a wing body. The data show the strake to exhibit expected stable vortex characteristics. It was found that, apart from increasing sweep, conically cambered delta wings developed drag levels approaching that of attached flow with increasing either the lift or the wing camber height, lastly, an approximate vortex flow design method, based on the suction analogy, is outlined and an example is given.

Lamar, J. E.↗

NASA NTRS1978

Recent theoretical developments and experimental studies pertinent to vortex flow aerodynamics - With a view towards design

A review is presented of recent progress in a research program directed towards the development of an improved vortex-flow technology base. It is pointed out that separation induced vortex-flows from the leading and side edges play an important role in the high angle-of-attack aerodynamic characteristics of a wide range of modern aircraft. In the analysis and design of high-speed aircraft, a detailed knowledge of this type of separation is required, particularly with regard to critical wind loads and the stability and performance at various off-design conditions. A description of analytical methods is presented. The theoretical methods employed are divided into two classes which are dependent upon the underlying aerodynamic assumptions. One conical flow method is considered along with three different nonconical flow methods. Comparisons are conducted between the described methods and available aerodynamic data. Attention is also given to a vortex flow drag study and a vortex flow wing design using suction analogy.

Lamar, J. E.↗

NASA NTRS1978

Theoretical estimation of the transonic aerodynamic characteristics of a supercritical-wing transport model with trailing-edge controls

A method for rapidly estimating the overall forces and moments at supercritical speeds, below drag divergence, of transport configurations with supercritical wings is presented. The method was also used for estimating the rolling moments due to the deflection of wing trailing-edge controls. This analysis was based on a vortex-lattice technique modified to approximate the effects of wing thickness and boundary-layer induced camber. Comparisons between the results of this method and experiment indicate reasonably good correlation of the lift, pitching moment, and rolling moment. The method required much less storage and run time to compute solutions over an angle-of-attack range than presently available transonic nonlinear methods require for a single angle-of-attack solution.

Luckring, J. M.↗

NASA NTRS1978

Theoretical and experimental aerodynamics of strake-wing interactions up to high angles-of-attack

This paper reports on an experimental investigation where the longitudinal aerodynamic characteristics were determined up to high angles-of-attack for configurations employing parametric variations in strake span and wing sweep and includes correlations with theory. The investigation included both component and complete configuration studies to provide information for the analysis of interaction effects. Comparisons between strake-wing and high canard-wing configurations demonstrate the strake-wing to develop higher lift coefficients than did the canard-wing due to enhanced interference effects. Correlations with theory demonstrate the suction analogy to be a useful method for estimating the effects of vortex flow aerodynamics on both component and total forces and moments.

Luckring, J. M.↗

NASA NTRS1977

Theoretical and experimental analysis of longitudinal and lateral aerodynamic characteristics of skewed wings at subsonic speeds to high angles of attack

The effects of sweep and aspect ratio on the longitudinal and lateral-directional aerodynamic characteristics of low-aspect-ratio skewed (oblique) wings having separation-induced vortex flows along leading and side edges were investigated in the Langley high-speed 7- by 10-foot tunnel at a low-subsonic Mach number. The theoretical analysis used the vortex-lattice method for estimating attached-flow aerodynamic characteristics and the leading-edge suction analogy of Polhamus for estimating separation induced vortex-flow effects. Experimental results were compared with asymmetric, separated, vortex flow theory.

Luckring, J. M.↗

NASA NTRS1976

Some recent applications of the suction analogy to asymmetric flow situations

A recent extension of the suction analogy for the estimation of vortex loads on asymmetric configurations was reviewed. This includes the asymmetric augmented vortex lift and the forward sweep effect on side edge suction. Application of this extension to a series of skewed wings has resulted in an improved estimating capability for a wide range of asymmetric flow situations. Hence, the suction analogy concept now has more general applicability for subsonic lifting surface analysis.

Luckring, J. M.↗

NASA NTRS1976

An application of the suction analog for the analysis of asymmetric flow situations

A recent extension of the suction analogy for estimation of vortex loads on asymmetric configurations is reviewed. This extension includes asymmetric augmented vortex lift and the forward sweep effect on side edge suction. Application of this extension to a series of skewed wings has resulted in an improved estimating capability for a wide range of asymmetric flow situations. Hence, the suction analogy concept now has more general applicability for subsonic lifting surface analysis.

Luckring, J. M.↗