Engineering topics
Publications and source records attributed to Lo, Y. T..
A feed network comprised of a combination of coplanar waveguide and slot transmission line is described for use in an array module of four microstrip elements. Examples of the module incorporating such networks are presented as well as experimentally obtained impedance and radiation characteristics.
A simple microstripline feed network for an array module comprising four microstrip elements is described. The advantages and disadvantages of the network are discussed as well as a theoretical explanation for the radiation characteristics of array modules using the network.
In February, an initial computer program to be used in analyzing the four-element array module was completed. This program performs the analysis of modules composed of four rectangular patches which are corporately fed by a microstrip line network terminated in four identical load impedances. Currently, a rigorous full-wave analysis of various types of microstrip line feed structures and patches is being performed. These tests include the microstrip line feed between layers of different electrical parameters. A method of moments was implemented for the case of a single dielectric layer and microstrip line fed rectangular patches in which the primary source is assumed to be a magnetic current ribbon across the line some distance from the patch. Measured values are compared with those computed by the program.
A method of computing the input impedance for the probe fed circular microstrip antenna with thick dielectric substrate is presented. Utilizing the framework of the cavity model, the fields under the microstrip patch are expanded in a set of modes satisfying the boundary conditions on the eccentrically located probe, as well as on the cavity magnetic wall. A mode-matching technique is used to solve for the electric field at the junction between the cavity and the coaxial feed cable. The reflection coefficient of the transverse electromagnetic (TEM) mode incident in the coaxial cable is determined, from which the input impedance of the antenna is computed. Measured data are presented to verify the theoretical calculations. Results of the computation of various losses for the circular printed antenna as a function of substrate thickness are also included.
It is well known that the sidelobe structure of a reflector antenna is highly susceptible to random surface errors, and that in most applications it is not adequate to investigate only the average behavior of the antenna. In this study, an attempt is made to determine the probability distribution of the sidelobe level of a reflector antenna subject to some random surface errors. Specifically, the random pattern function is considered and its sidelobe level studied using the level-upcrossing theory. Both the degradation of the maximum sidelobe and the degradation of the sidelobe region with respect to an International Radio Consultative Committee (CCIR) sidelobe envelope are obtained. The theoretical results are found in excellent agreement with those obtained by Monte Carlo simulations. Finally, some useful tolerance charts are presented.
Attenuation properties of the normal modes in an overmoded waveguide coated with a lossy material were analyzed. It is found that the low-order modes, can be significantly attenuated even with a thin layer of coating if the coating material is not too lossy. A thinner layer of coating is required for large attenuation of the low-order modes if the coating material is magnetic rather than dielectric. The Radar Cross Section (RCS) from an uncoated circular guide terminated by a perfect electric conductor was calculated and compared with available experimental data. It is confirmed that the interior irradiation contributes to the RCS. The equivalent-current method based on the geometrical theory of diffraction (GTD) was chosen for the calculation of the contribution from the rim diffraction. The RCS reduction from a coated circular guide terminated by a PEC are planned schemes for the experiments are included. The waveguide coated with a lossy magnetic material is suggested as a substitute for the corrugated waveguide.
Numerical methods to analyze electromagnetic scattering are presented. The dispersions and attenuations of the normal modes in a circular waveguide coated with lossy material were completely analyzed. The radar cross section (RCS) from a circular waveguide coated with lossy material was calculated. The following is observed: (1) the interior irradiation contributes to the RCS much more than does the rim diffraction; (2) at low frequency, the RCS from the circular waveguide terminated by a perfect electric conductor (PEC) can be reduced more than 13 dB down with a coating thickness less than 1% of the radius using the best lossy material available in a 6 radius-long cylinder; (3) at high frequency, a modal separation between the highly attenuated and the lowly attenuated modes is evident if the coating material is too lossy, however, a large RCS reduction can be achieved for a small incident angle with a thin layer of coating. It is found that the waveguide coated with a lossy magnetic material can be used as a substitute for a corrugated waveguide to produce a circularly polarized radiation yield.
A simple microstrip antenna can be made to radiate EM waves of any polarization, in particular, the circular polarization (CP) without any phasing network and power divider. A simple and accurate theory for this family of antennas was developed. However, the CP bandwidth, (CPBW) the bandwidth in which the axial ratio (AR) is less than a certain specified value, is very small. Most of the experimental designs were made for a feed placed along the diagonal of the patch. It is shown that there are practically infinitely many possible designs with different feed location. The speculation that other designs might give a wider bandwidth is clarified and an effective method for broadening the bandwidth is shown.
The physical layout of the array elements and the proximity of the microstrip feed network makes the input impedance and radiation pattern values dependent upon the effects of mutual coupling, feedline discontinuities and feed point location. The extent of these dependences was assessed and a number of single patch and module structures were constructed and measured at an operating frequency of approximately 4.0 GHz. The empirical results were compared with the ones which were theoretically predicted by the cavity model of thin microstrip antennas. Each element was modelled as an independent radiating patch and each microstrip feedline as an independent, quasi-TEM transmission line. The effects of the feedline discontinuities are approximated by lumped L-C circuit models.
The wave attenuation in a cylindrical waveguide coated with lossy dielectric material was studied. The scope was extended to the high frequency case for calculating attenuation coefficients and propagation constants of a dielectric coated circular waveguide. The magnetic material coating was studied. At low frequency a one way 3dB attenuation was achieved within a longitudinal distance of one diameter. A software program was generated to plot the field patterns of the lowest 30 modes in the cylindrical waveguides.
Single element microstrip antenna for dual-frequency operation have been investigated. By placing shorting pins at appropriate locations in the patch, the ratio of two-band frequencies can be varied from 3 to 1.8. In many applications a smaller ratio is desired, and this can be achieved by introducing slots in the patch. In so doing, the ratio can be reduced to less than 1.3. For this type of antenna, a hybrid multiport theory is developed and theoretical results are found to be in excellent agreement with the measured.
The modal attenuation constants in a cylindrical waveguide coated with a lossy dielectric material are studied as functions of frequency, dielectric constant, and thickness of the dielectric layer. A dielectric material best suited for a large attenuation is suggested. Using Kirchhoff's approximation, the field attenuation in a coated waveguide which is illuminated by a normally incident plane wave is also studied. For a circular guide which has a diameter of two wavelengths and is coated with a thin lossy dielectric layer (omega sub r = 9.1 - j2.3, thickness = 3% of the radius), a 3 dB attenuation is achieved within 16 diameters.
The wave propagation inside a cylindrical waveguide, coated with lossy dielectric material due to the incidence of a plane wave at the open end of the guide, was studied. The general properties of the normal mode propagation were investigated.
Modal wave solutions of isotropic plasma-filled parallel-plate waveguide examined, using cold and warm plasma models without collision
Current distribution and input admittance of infinitely long cylindrical antenna driven by slice generator and immersed in anisotropic plasma
Reflection and transmission of electromagnetic waves at interface between stationary isotropic medium and moving anisotropic medium
Third moment equation derived from Boltzmann- Vlasov equation for wave propagation in plasmas with very strong magnetic field used instead of state equation
Radiation due to time-harmonic source and field solution of electric dipole in moving uniaxial anisotropic medium by Minkowski theory