Engineering topics
Lo, C. F.
Publications and source records attributed to Lo, C. F..
GaN metal-insulator-semiconductor high-electron-mobility-transistor with plasma enhanced atomic layer deposited AlN as gate dielectric and passivation
Explore the source record for details and available documents.
Proton irradiation energy dependence of dc and rf characteristics on InAlN/GaN high electron mobility transistors
The effects of proton irradiation energy on dc and rf characteristics of InAlN/GaN high electron mobility transistors (HEMTs) were investigated. A fixed proton dose of 51015 cm2 with 5, 10, and 15 MeV irradiation energies was used in this study. For the dc characteristics, degradation was observed for sheet resistance, transfer resistance, contact resistivity, saturation drain current, maximum transconductance, reverse-bias gate leakage current, and sub-threshold drain leakage current for all the irradiated HEMTs; however, the degree of the degradation was decreased as the irradiation energy increased. Similar trends were obtained for the rf performance of the devices, with 10% degradation of the unity gain cut-off frequency (fT) and maximum oscillation frequency ( fmax) for the HEMTs irradiated with 15 MeV protons but 30% for 5 MeV proton irradiation. The carrier removal rate was in the range 0.66 1.24 cm1 over the range of proton energies investigated
SnO2-gated AlGaN/GaN high electron mobility transistors based oxygen sensors
Hydrothermally grown SnO2 was integrated with AlGaN/GaN high electron mobility transistor (HEMT) sensor as the gate electrode for oxygen detection. The crystalline of the SnO2 was improved after annealing at 400 C. The grain growth kinetics of the SnO2 nanomaterials, together with the O2 gas sensing properties and sensing mechanism of the SnO2 gated HEMT sensors were investigated. Detection of 1% oxygen in nitrogen at 100 C was possible. A low operation temperature and low power consumption oxygen sensor can be achieved by combining the SnO2 films with the AlGaN/GaN HEMT structure
The effects of proton irradiation on the reliability of InAlN/GaN high electron mobility transistors
We have investigated the effect of proton irradiation on reliability of InAlN/GaN high electron mobility transistors (HEMTs). Devices were subjected to 5-15 MeV proton irradiations with a fixed dose of 5 1015 cm-2, or to a different doses of 2 1011, 5 1013 or 2 1015 cm-2 of protons at a fixed energy of 5 MeV. During off-state electrical stressing, the typical critical voltage for un-irradiated devices was 45 to 55 V. By sharp contrast, no critical voltage was detected for proton irradiated HEMTs up to 100 V, which was instrument-limited. After electrical stressing, no degradation was observed for the drain or gate current-voltage characteristics of the proton-irradiated HEMTs. However, the drain current decreased ~12%, and the reverse bias gate leakage current increased more than two orders of magnitude for un-irradiated HEMTs as a result of electrical stressing.
Improved Off-State Stress Critical Voltage on AlGaN/GaN High Electron Mobility Transistors Utilizing Pt/Ti/Au Based Gate Metallization
The critical voltage for degradation of AlGaN/GaN high electronmobility transistors (HEMTs) employed with the Pt/Ti/Au gatemetallization instead of the commonly used Ni/Au wassignificantly increased during the off-state stress. The typicalcritical voltage for HEMTs with Ni/Au gate metallization wasaround -60V. By sharp contrast, no critical voltage was observedfor the HEMTs with Pt/Ti/Au gate metallization, even up to -100V,which was the instrumental limitation in this experiment. BothSchottky forward and reverse gate characteristics of the Ni/Audegraded once the gate voltage passed the critical voltage ofaround -60V. There was no degradation exhibited for the HEMTswith Pt-gated HEMTs.
Fabrication and Characterization of Self-aligned InAlAs/InGaAsSb/InGaAs Double Heterojunction Bipolar Transistors
A trilevel resist system was employed to fabricate self-aligned,submicron emitter finger In0.52Al0.48As/In0.42Ga0.58As0.77Sb0.23/In0.53Ga0.47As double heterojunction bipolar transistors (DHBTs).Selective wet-etchants were used to define the emitter fingers andto form an InGaAs guard-ring around the emitter fingers. Due tothe low energy bandgap of the InGaAsSb base layer and type IIbase-collector junction, a low turn-on voltage of 0.38 V at 1 A/cm2and a high dc current gain of 123.8 for a DHBT with a 0.65 × 8.65μm2 emitter area were obtained. A unity gain cut-off frequency(fT) of 260 GHz and a maximum oscillation frequency (fmax) of 485GHz at JC = 302 kA/cm2 were achieved.
Fabrication of InAlAs/InGaAsSb/InGaAs double heterojunction bipolar transistors
A trilevel resist system was employed to fabricate self-aligned, submicron emitter finger In0.52Al0.48As/ In0.42Ga0.58As0.77Sb0.23 / In0.53Ga0.47As double heterojunction bipolar transistors DHBTs. Selective wet-etchants were used to define the emitter fingers and to form an InGaAs guard-ring around the emitter fingers. Due to the low energy bandgap of the InGaAsSb base layer and type II base-collector junction, a low turn-on voltage of 0.38 V at 1 A/cm2 and a high dc current gain of 123.8 for a DHBT with a 0.658.65 m2 emitter area were obtained. A unity gain cutoff frequency fT of 260 GHz and a maximum oscillation frequency fmax of 485 GHz at JC =302 kA/cm2 were achieved.
Comparison of dc performance of Pt/Ti/Au- and Ni/Au-Gated AlGaN/GaN High Electron Mobility Transistors
We have demonstrated significant improvements of AlGaN/GaN High Electron Mobility Transistors (HEMTs) dc performance by employing Pt/Ti/Au instead of the conventional Ni/Au gate metallization. During off-state bias stressing, the typical critical voltage for HEMTs with Ni/Au gate metallization was ~ -45 to -65V. By sharp contrast, no critical voltage was observed for HEMTs with Pt/Ti/Au gate metallization, even up to -100V, which was the instrumental limitation in this experiment. After the off-state stressing, the drain current of Ni/Au gated-HEMTs decreased by~ 15%. For the Pt-gate HEMTs, no degradation of the drain current occurred and there were minimal changes in the Schottky gate characteristics for both forward and reverse bias conditions. The HEMTs with Pt/Ti/Au metallization showed an excellent drain on/off current ratio of 1.5 108. The on/off drain current ratio of Ni-gated HEMTs was dependent on the drain bias voltage and ranged from 1.2 107 at Vds=5V and 6 105
Effects of proton irradiation on dc characteristics of InAlN/GaN high electron mobility transistors
The effects of proton irradiation on the dc characteristics of InAlN/GaN high electron mobility transistors were investigated. In this study we used 5 MeV protons with doses varying from 21011 to 21015 cm2. The transfer resistance and contact resistivity suffered more degradation as compared to the sheet resistance. With irradiation at the highest dose of 21015 cm2, both forward- and reverse-bias gate currents were increased after proton irradiation. A negative threshold-shift and reduction of the saturation drain current were also observed as a result of radiation-induced carrier scattering and carrier removal. Devices irradiated with doses of 21011 to 21015 cm2 exhibited minimal degradation of the saturation drain current and extrinsic trans- conductance. These results show that InAlN/GaN high electron mobility transistors are attractive for space-based applications when high-energy proton fluxes are present. VC 2011 American Vacuum Society. [DOI: 10.1116/1.3644480]
Improvement of Off-State Stress Critical Voltage by Using Pt-gated AlGaN/GaN High Electron Mobility Transistors
By replacing the commonly used Ni/Au gate metallization with Pt/Ti/Au, the critical voltage for degradation of AlGaN/GaN High Electron Mobility Transistors (HEMTs) during off-state biasing stress was significantly increased. The typical critical voltage for the HEMTs with Ni/Au gate metallization was around -55V. By sharp contrast, no critical voltage was observed for the HEMTs with Pt/Ti/Au gate metallization, even up -100V, which was the instrumental limitation in this experiment. Both Schottky forward and reverse gate characteristics of the Ni/Au degraded once the gate voltage passed the critical voltage of -55V. There was no degradation exhibited for the HEMTs with Pt/Ti/Au gate metallization.
Normally-ON/OFF AlN/GaN High Electron Mobility Transistors
We report on the novel normally-on/off AlN/GaN high electron mobility transistors (HEMTs) grown by plasma-assisted molecular beam epitaxy. With simple oxygen plasma exposure, the threshold voltage can be tuned from -2.76 V to +1.13 V depending on the treatment time. The gate current was reduced and gate current-voltage curve show metal-oxide semiconductor diode-like characteris-tics after oxygen plasma exposure. The extrinsic trans-conductance of HEMTs decreased with increasing oxy-gen plasma exposure time due to the thicker Al oxide formed on the gate area. The unity current gain cut-off frequency, fT, and the maximum frequency of oscillation, fmax, were 20.4 GHz and 36.5 GHz, respectively, for a enhancement-mode HEMT with the gate dimension of 0.4 100 m2.
Isolation blocking voltage of nitrogen ion-implanted AlGaN/GaN high electron mobility transistor structure
Nitrogen ion-implanted AlGaN/GaN high electron mobility transistor structures showed an isolation blocking voltage of 900 V with a leakage current at 1 A/mm across an implanted isolation-gap of 10 m between two Ohmic pads. The effect of implanted gap distance 1.7, 5, or 10 m between two Ohmic contact pads was evaluated. The isolation current density was determined to be solely dependent on the applied field between the contact pads. A model using a combination of resistive current and Poole Frenkel current is consistent with the experimental data. The resistance of the isolation implantation region significantly decreased after the sample was annealed at temperatures above 600 C.
Passivation of AlN/GaN HEMTs Using Ozone Treatment
Ozone treatment of AlN on AlN/GaN heterostructures produces effective surface passivation and chemical resistance to the AZ positive photoresist developer used for subsequent device fabrication. The ozone-passivated AlN/GaN High Electron Mobility Transistors (HEMTs) exhibited low gate leakage currents, high gate modulation voltage, and minimal drain current degradation during gate pulse measurements. With an additional oxygen plasma treatment on the gate area prior to the gate metal deposition, enhancement-mode AlN/GaN high electron mobility transistors were realized. The gate characteristics of the HEMTs treated with the ozone and oxygen plasma behaved in a manner similar to a metal oxide semiconductor diode-like gate current-voltage characteristic instead of a Schottky diode. Drain breakdown voltages of 23 and 43V for d- and e-mode HEMT were obtained, respectively. For d-mode HEMTs, there was no reduction in drain current during the gate pulse measurements at frequencies of 1 kHz, 10 kHz and 100 kHz. For the e-mode HEMT, the drain current was reduced 5% at 100 kHz.
Development of Enhancement Mode AlN/GaN HEMTs
Demonstration of enhancement mode AlN/GaN high electron mobility transistor (HEMT) using oxygen plasma treatment on the gate area prior to the gate metalliation deposition was achieved. Starting with a depletion mode AlN/GaN HEMT, the threshold voltage of the HEMT could be shifted from 3.2 to 1V depending on the oxygen plasma treatment time to convert the AlN into Al oxide. The gate current was also reduced when the threshold voltage
Proton Irradiation Effects on Sb-based Heterojunction Bipolar Transistors
In0.52Al0.48As/In0.39Ga0.61As0.77Sb0.23/In0.53Ga0.47As double heterojunction bipolar transistors (DHBTs) were irradiated with 5 MeV protons at fluences from 2 1011 to 2 1015 protons/cm2. The radiation produced significant increases in generation-recombination leakage current in both emitter-base and base-collector junctions. The DHBTs irradiated with a dose of 2 1011 cm-2, which was equivalent to around 40 years of exposure in low earth orbit, showed minimal changes in the junction ideality factor, generation recombination leakage current, current gain and output conductance. The InAlAs/InGaAsSb/InGaAs DHBTs appear to be well-suited to space or nuclear industry applications.
Supersonic Laminar Flow Control Research
The objective of this research is to understand supersonic laminar flow stability, transition and active control. Some prediction techniques are developed or modified to analyze laminar flow stability. The effects of distributed heating and cooling as an active boundary layer control technique are studied. The primary tasks of the research apply to the NASA/Ames Proof-of-Concept (PoC) and the Laminar Flow Supersonic Wind Tunnel's (LFSWT's) nozzle design with laminar flow control and are listed as follows: (1) Predictions of supersonic laminar boundary layer stability and transition; (2) Effects of wall heating and cooling on supersonic laminar flow control on a flat plate; (3) Performance evaluation of the PoC and LFSWT nozzle designs with wall heating and cooling applied at different locations and various lengths; (4) Effects of a conducted -vs- pulse wall temperature distribution for the LFSWT; and (5) Application of wall heating and/or cooling to laminar boundary layer and flow separation control of airfoils and investigation of related active control techniques.
A wall interference assessment and correction system
A wall signature method has been selected to be adapted for the Ames 12-ft Wind Tunnel WIAC system. This uses limited measurements of the static pressure at the wall, in conjunction with the solid wall boundary condition, to determine the strength and distribution of singularities representing the test article. The singularities are used to estimate wall interference at the model location. The development and implementation of a working prototype will be completed, delivered and documented with a software manual.