Engineering Papers⌕ Search

Engineering topics

Lloyd, Randy

Publications and source records attributed to Lloyd, Randy.

Initial Temperature Testing of Advanced Manufactured Melt Wire Package

As a part of the In-Pile Instrumentation Program, The Idaho National Laboratory (INL) has recently established in-house capabilities to fabricate and test new advanced manufactured sensors for measuring the peak irradiation temperature inside a nuclear test reactor. Although nuclear test reactors can use standard methods of real-time temperature monitoring, such as thermocouples, the complexity of feedthroughs and attachment complications to collect real-time measurements greatly increases the cost of the experiment. Passive monitoring techniques may be utilized that exploit the melting point of well characterized material (standard melt wires), however, the limited space available for instrumentation during experiments is also a challenge. To accommodate the challenge, INL has expanded its temperature detection instrumentation capabilities paired with the advancement of in-house advanced manufacturing options to include printed melt wires for peak irradiation temperature measurement. The advanced manufactured melt wire package can determine peak temperatures in experiments that can fit the challenging space available during irradiation. Recent results and knowledge from this ongoing work have made it possible to develop unique temperature sensors that can accomplish user specific temperature ranges inside the harsh environments experienced during radiation testing. This report summarizes the initial temperature testing using fabricated melt wires with two different melting temperatures, silver (melting temperature of ~960 °C) and solder (melting temperature of ~160 °C), that were initially tested for their relative melting points using non-standard method of furnace and hot plate testing under normal air conditions. Future work will include more controlled way of testing printed melt wires under inert gas with multiple temperature measurements followed by comparison of standard melt wire package performance for baseline characterization.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Elevated temperature tensile tests on DU–10Mo rolled foils

We report that studies were completed to obtain tensile mechanical properties for uranium-10wt.% molybdenum (U-10Mo) foils which were subjected to four different thermomechanical processing conditions. U-Mo alloy foils are being investigated to support fuel conversion of high power research reactors from their current high enriched fuel form to a low enriched fuel form. Mechanical properties of the fuel foil have an effect on irradiation performance and fuel fabrication and therefore are required to support modeling and qualification of new low-enriched uranium monolithic fuel plate designs. The data contained in this document contributes to fuel qualification by fulfilling the requirement that physical properties related to fuel meat be established. It is expected that depleted uranium-10wt% Mo (DU–10Mo) mechanical behavior is representative of the low-enriched U10-Mo to be used in actual fuel plates; therefore DU–10Mo was studied to simplify material processing, handling, and testing requirements. In this report, the different thermomechanical treatments included variations of wrought hot and cold rolling reduction and post rolling annealing. Each of the four foils was hot rolled. After hot rolling reduction, three of the four foils were further reduced by cold rolling. One of the three was reduced a further 20% by cold rolling, and the remaining two were reduced 50% by cold rolling. Following cold rolling reduction, one of the two foils which had been reduced 50% by cold rolling was annealed at 650?°C. Performing this analysis allows assessment of the impact of foil fabrication history on the resultant tensile properties DU–10Mo fuel foils. Tensile properties of DU–10Mo at room temperature through approximately 400 °C determined from the tests conducted herein suggest the material is stronger and has lower ductility than what has been reported previously in the literature. The explanation for these differences has yet to be determined, but is likely related to differences in grain size and/or impurity content, and variation in fabrication history. At the highest temperatures tested (550 °C) better agreement between the values reported here and available literature was found. As expected, yield and ultimate tensile strength decreased with increasing test temperature. Generally, the yield stress for all foil processing conditions was found to be in the range of 1100 MPa for room temperature tests, and in the range of 200 MPa for tests conducted at 550 °C. Ultimate tensile stress was in the range of 1175 MPa at room temperature, decreasing to approximately 225 MPa at 550 °C. Lastly, elongation increased significantly, from 0 to 2% at room temperature to 50% or more for the tests at 550 °C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Baseline Graphite Initial Mechanical Test Report

The Next Generation Nuclear Plant (NGNP) Project is tasked with selecting a high temperature gas reactor technology that will be capable of generating electricity and supplying large amounts of process heat. The NGNP is presently being designed as a helium-cooled high temperature gas reactor (HTGR) with a large graphite core. The graphite baseline characterization project is conducting the research and development (R&D) activities deemed necessary to fully qualify nuclear-grade graphite for use in the NGNP reactor. One of the major fundamental objectives of the project is establishing nonirradiated thermomechanical and thermophysical properties by characterizing lot-to-lot and billet-to-billet variations (for probabilistic baseline data needs) through extensive data collection and statistical analysis. The reactor core will be made up of stacks of graphite moderator blocks. In order to gain a more comprehensive understanding of the varying characteristics in a wide range of suitable graphites, any of which can be classified as “nuclear grade,” an experimental program has been initiated to develop an extensive database of the baseline characteristics of numerous candidate graphites. Various factors known to affect the properties of graphite will be investigated, including specimen size, spatial location within a graphite billet, specimen orientation within a billet (either parallel to [P] or transverse to [T] the long axis of the as-produced billet), and billet-to-billet variations within a lot or across different production lots. Because each data point is based on a certain position within a given billet of graphite, particular attention must be paid to the traceability of each specimen and its spatial location and orientation within each billet. The evaluation of these properties is discussed in the Graphite Technology Development Plan (Windes et. al 2007). One of the key components in the evaluation of these graphite types will be mechanical testing of specimens drawn from carefully controlled sections of each billet. This report is confirmation that the test procedures are in place and approved, and that mechanical testing of graphite under the Baseline Graphite Characterization program has commenced.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗