Engineering Papers⌕ Search

Engineering topics

Liu, Xiang

Publications and source records attributed to Liu, Xiang.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High–Energy Earth–Abundant Cathodes with Enhanced Cationic/Anionic Redox for Sustainable and Long–Lasting Na–Ion Batteries

Layered iron/manganese-based oxides are a class of promising cathode materials for sustainable batteries due to their high energy densities and earth abundance. However, the stabilization of cationic and anionic redox reactions in these cathodes during cycling at high voltage remain elusive. Here, an electrochemically/thermally stable P2-Na 0.67 Fe 0.3 Mn 0.5 Mg 0.1 Ti 0.1 O 2 cathode material with zero critical elements is designed for sodium-ion batteries (NIBs) to realize a highly reversible capacity of ≈210 mAh g –1 at 20 mA g –1 and good cycling stability with a capacity retention of 74% after 300 cycles at 200 mA g –1 , even when operated with a high charge cut-off voltage of 4.5 V versus sodium metal. Combining a suite of cutting-edge characterizations and computational modeling, it is shown that Mg/Ti co-doping leads to stabilized surface/bulk structure at high voltage and high temperature, and more importantly, enhances cationic/anionic redox reaction reversibility over extended cycles with the suppression of other undesired oxygen activities. This work fundamentally deepens the failure mechanism of Fe/Mn-based layered cathodes and highlights the importance of dopant engineering to achieve high-energy and earth-abundant cathode material for sustainable and long-lasting NIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Small scale tensile testing technique for measuring grain boundary strength of neutron-irradiated materials in focused ion beam systems

Irradiation induced defects on grain boundaries (GBs) can lead to GB strength degradation and cause intergranular cracking in structural materials, affecting the safe operation and service life of nuclear reactors. Establishing the quantitative relationship between the strength and character/microchemistry for individual GB in an effort of integrating experimental measurements and multiscale simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Suppressing strain propagation in ultrahigh-Ni cathodes during fast charging via epitaxial entropy-assisted coating

Surface reconstruction and the associated severe strain propagation have long been reported as the major cause of cathode failure during fast charging and long-term cycling. Despite tremendous attempts, no known strategies can simultaneously address the electro-chemomechanical instability without sacrificing energy and power density. Here we report an epitaxial entropy-assisted coating strategy for ultrahigh-Ni LiNi x Co y Mn 1-x-y O 2 (x ≥ 0.9) cathodes via an oriented attachment-driven reaction between Wadsley-Roth phase-based oxides and the layered-oxide cathodes. Further, the high anti-cracking and anti-corrosion tolerances as well as the fast ionic transport of the entropy-assisted surface effectively improved the fast charging/discharging capability, wide temperature tolerance and thermal stability of the ultrahigh-Ni cathodes. Comprehensive analysis from the primary and secondary particle level to the electrode level using multi-scale in situ synchrotron X-ray probes reveals greatly reduced lattice dislocations, anisotropic lattice strain and oxygen release as well as improved bulk/local structural stability, even when charging beyond the threshold state of charge (75%) of layered cathodes. Layered Ni-rich oxide cathodes are susceptible to challenges with surface reconstruction and strain propagation, limiting their cyclability. The authors propose a solution involving oriented attachment-driven reactions, utilizing Wadsley-Roth nanocrystals and layered oxide to induce an epitaxial entropy-assisted coating, effectively addressing these issues.

25 ENERGY STORAGE↗
DOE OSTI2024

Protonation Stimulates the Layered to Rock Salt Phase Transition of Ni‐Rich Sodium Cathodes

Abstract Protonation of oxide cathodes triggers surface transition metal dissolution and accelerates the performance degradation of Li‐ion batteries. While strategies are developed to improve cathode material surface stability, little is known about the effects of protonation on bulk phase transitions in these cathode materials or their sodium‐ion battery counterparts. Here, using NaNiO 2 in electrolytes with different proton‐generating levels as model systems, a holistic picture of the effect of incorporated protons is presented. Protonation of lattice oxygens stimulate transition metal migration to the alkaline layer and accelerates layered‐rock‐salt phase transition, which leads to bulk structure disintegration and anisotropic surface reconstruction layers formation. A cathode that undergoes severe protonation reactions attains a porous architecture corresponding to its multifold performance fade. This work reveals that interactions between electrolyte and cathode that result in protonation can dominate the structural reversibility/stability of bulk cathodes, and the insight sheds light for the development of future batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Inhibit the strain accumulation for 5V spinel cathode by mitigating the phase separation during high voltage stage

LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel cathode is a potential cathode material for high-power, low-cost lithium-ion batteries (LIBs) due to its low raw material cost, high operating voltage and efficient lithium-ion transport channel. However, LNMO suffers from structural stability due to the two-phase-transformation during charge/discharge process, leading to poor cycling performance. Here, to address the issues, we have constructed a homogeneous aggregated LNMO cathode with a multifaceted primary particle, namely the LNMO with single-crystal secondary particles (SSP LNMO). Ex situ and in situ characterizations including the synchrotron X-ray diffraction, the neutron diffraction and full pouch cell validated that the SSP LNMO exhibit a single solid-solution reactions with a restrained lattice evolution during the delithiation/lithiation process. This is in contrast to the normal LNMO cathode, which demonstrates a significant two-phase transition from spinel Li 1-x Ni 0.5 Mn 1.5 O 4 to rock-salt MnO 2 at high voltage. Therefore, the SSP LNMO has greatly improved cycle life compared to the normal LNMO cathode. Overall, this study demonstrates the possibility of constructing LNMO based on primary-grain morphology modulation to improve the intrinsic stability of LIBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Transmission electron microscopy investigation of phase transformation and fuel constituent redistribution in neutron irradiated U-10wt.%Zr fuel

Uranium-10wt.%zirconium (U-10wt.%Zr) is a primary candidate for fast reactor nuclear fuels. However, there is a lack of data characterizing neutron irradiated crystallographic phases and chemistry. In the current study, the microstructural evolution of a U-10wt.%Zr fuel neutron irradiated to a burnup of 5.7 at.% was investigated by scanning transmission electron microscopy, energy dispersive spectroscopy, and selected area electron diffraction to determine the major phases, alterations in microstructure, and variations in local chemical composition at different localities of a fuel cross-section. The current study revealed that the irradiated U-10wt.%Zr fuel was comprised of various major phases, including a-U, ß-U, and d-UZr2, as well as amorphous and crystalline solid fission product (FP) precipitates within different regions of the fuel cross-section. Regions A and A/B in the center of the fuel were comprised of U-rich, U-intermediate, and U-lean localities with a-U and d-UZr 2 composing the major phases. Regions B and C in the intermediate and peripheral fuel localities, respectively, were comprised of a-U grains, U-rich (ß-U) grains with Zr-rich precipitates, U-intermediate grains (d-UZr2), and solid FP precipitates. The major phases identified were associated with the nanoscopic chemical concentrations, the phase diagram, and the as-characterized specimen temperature, with the exception of the non-equilibrium ß-U phase identified in region B. The U-lean localities in regions A, A/B, B, and C were Zr-enriched pathways along subgrain/grain boundaries. This phenomenon suggests that Zr is susceptible to radiation-induced segregation in U-Zr fuels and indicates a new mechanism for constituent redistribution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Novel catalysts with multivalence copper for organic pollutants removal from wastewater with excellent selectivity and stability in Fenton‐like process under neutral pH conditions

Abstract Fenton‐like reaction has been widely used for organics degradation. However, most Fenton‐like reaction works at low pH range (pH < 4) with uncontrollable selectivity of hydroxyl radicals from H 2 O 2 activation, and unsatisfied catalyst stability, which is compromised advanced oxidation performance for water/wastewater treatments. In this work, to solve the drawbacks, novel copper catalysts were fabricated via hydrogen reduction/calcination of Cu 2+ ‐supported Al/MCM‐41 with precisely controllable copper valence state. Compared with catalysts with monovalence copper (i.e., CuO, Cu, and Cu 2+ ), the obtained catalysts with multivalence copper present higher selectivity, excellent stability towards •OH radical pathways, and outperformance in p CBA degradation efficiency at neutral state. In addition, the fabricated catalysts also exhibited excellent phenol removal efficiency (75.5%) and H 2 O 2 utilization efficiency (47.9%) within neutral environment. Moreover, the degradation efficiency of phenol approaches to 100% within only 2 h. The catalyst also shows good stability for organic pollutants removal, which shows good potential in catalytic oxidation for phenolic compounds‐containing wastewater in Fenton‐like reaction, especially under neutral pH conditions. Practitioner Points Multivalence copper presents great potentials for organic compounds removal at neutral condition. Multivalence copper shows higher selectivity toward •OH and good stability at neutral condition. Multivalence copper exhibiters outperformed phenol removal efficiency at neutral condition.

Li, Haitao↗
DOE OSTI2022

Thermal Runaway of Nonflammable Localized High‐Concentration Electrolytes for Practical LiNi 0.8 Mn 0.1 Co 0.1 O 2 |Graphite‐SiO Pouch Cells

Abstract With continuous improvement of batteries in energy density, enhancing their safety is becoming increasingly urgent. Herein, practical high energy density LiNi 0.8 Mn 0.1 Co 0.1 O 2 |graphite‐SiO pouch cell with nonflammable localized high concentration electrolyte (LHCE) is proposed that presents unique self‐discharge characteristic before thermal runaway (TR), thus effectively reducing safety hazards. Compared with the reference electrolyte, pouch cell with nonflammable LHCE can increase self‐generated heat temperature by 4.4 °C, increase TR triggering temperature by 47.3 °C, decrease the TR highest temperature by 71.8 °C, and extend the time from self‐generated heat to triggering TR by ≈8 h. In addition, the cell with nonflammable LHCE presents superior high voltage cycle stability, attributed to the formation of robust inorganic‐rich electrode–electrolyte interphase. The strategy represents a pivotal step forward for practical high energy and high safety batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Transmission electron microscopy study of a high burnup U-10Zr metallic fuel

To support the development of U-10 wt.% Zr (U-10Zr) metallic fuel for Gen IV sodium-cooled fast reactors, we analysed a solid, Na-bonded, U-10Zr (by weight percent) fuel cross section that was irradiated to a burnup of ~ 12.4 % at.% at the Fast Flux Test Facility (FFTF). Advanced characterization techniques, including site specific sample preparation by focused ion beam (FIB) and phase/chemical determination by transmission electron microscopy (TEM), were used to reveal the constituent redistribution of Zr, characterize the fuel phases and the secondary phases (such as solid fission products) present at the end of life. It is shown that the fuel pin cross section is divided into three major concentric zones: a Zr-rich central region, a Zr-lean intermediate region, and a Zr intermediate peripherical region. The phase characterization revealed that the irradiation environment enhanced the development and stabilization of phases not predicted by the standard equilibrium U-Zr phase diagrams. Comparing the current results with the ones from previous studies, it is reaffirmed that the irradiation temperature and the time spent in the reactor, rather than the fuel burnup, are the two factors that most influence the formation of redistribution zones and their extension along the fuel cross section. Various solid fission products precipitated inside the fission gas pores, such as lanthanides, ZrRu, BaTe, CsI, and Ba and Sr oxides. Here, this study provides unprecedented nanoscale understandings in the U-10Zr fuel system that may benefit fuel performance modelling and advanced fuel development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Electroactive materials for secondary batteries

A [P x Sb y M z ]p/[carbon] q composite where x, y, and z represent atomic percentage values and are x>0; y>0; and z≥0, M is an electrically conductive metal, p and q represent the weight percentage values of the composite wherein p and q are in the range of 0-100%, and is p>0.

25 ENERGY STORAGE↗
DOE OSTI2022

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Transmission Electron Microscopy based Characterization of a U-20Pu-10Zr Fuel Irradiated in Experimental Breeder Reactor-II

U-Pu-Zr metallic fuels are important fuel candidate for future advanced and/or test reactors. To better understand fuel performance and guide future fuel development, a U-20Pu-10Zr (in weight) metallic fuel irradiated in the Experimental Breeder Reactor was revisited using advanced electron microscopies. This fuel was irradiated to a burnup of 7.6 % at a peak cladding temperature of 521 °C. In this research, several transmission electron microscopy samples were extracted from different but representative radial locations of the fuel cross section using focused ion beam technique. Phase identification and chemical analysis with sub-micron spatial resolution was carried out using scanning transmission electron microscopy. Multiple phenomena that are critical to fuel performance, such as Zr phase and its distribution in a different matrix, were revealed in an unpreceded and highly detailed manner. An improved understanding of fuel reconstruction in U-Pu-Zr metallic fuel under reactor irradiation is provided.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Origin and regulation of oxygen redox instability in high-voltage battery cathodes

Oxygen redox at high-voltage has emerged as a transformative paradigm for high-energy battery cathodes such as layered transition-metal oxides by offering extra capacity beyond conventional transition-metal redox. However, these cathodes suffer from voltage hysteresis, voltage fade, and capacity drop upon cycling; single-crystalline cathodes have recently shown some improvements but these challenges still remain. We reveal the fundamental origin of oxygen redox instability to be originated from the domain boundaries that are present in single-crystalline cathode particles. By synthesizing single-crystalline cathodes free of domain boundaries, we show that the elimination of domain boundaries enhances the reversible lattice oxygen redox while inhibiting the irreversible oxygen release. Further, this leads to significantly suppressed structural degradation and improved mechanical integrity during battery cycling and abuse heating. The robust oxygen redox enabled through domain boundary control provides practical opportunities towards high-energy, long-cycling, and safe batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

A study on texture stability and the biaxial creep behavior of as-hydrided CWSR Zircaloy-4 cladding at the effective stresses from 55 MPa to 65 MPa and temperatures from 300°C to 400°C

The creep rupture of high burnup used nuclear fuel (> 45 GWD/MTU) cladding is regarded as one of the failure mechanisms during long-term dry storage. A high amount of zirconium hydride in the cladding matrix would degrade the mechanical properties of the cladding especially leading to delayed hydride cracking. To better understand the influence of zirconium hydride on the biaxial thermal creep performance and the crystalline texture stability of Zircaloy-4 cladding, the pressurized tube technique is applied to test the durability of the as-hydrided material. Tests were performed on as-received Zircaloy-4 tubular specimens as well as-hydrided ones with targeted 300 wt parts per million (wppm) or 750 wppm hydrogen. The biaxial creep experiments were conducted at temperatures from 300 degrees C to 400 degrees C and at equivalent stresses at mid-wall from 55 MPa to 65 MPa. The hydridation process prior to creep tests induces the formation of FCC delta-hydride platelets along the circumferential direction of the tube. This alignment and phase structure of hydride show no significant change after biaxial creep tests. The creep strain-rate negatively depends on the hydrogen content. The synchrotron wide-angle X-ray diffraction (WAXD) technique and electron backscatter diffraction (EBSD) analysis were applied for the study of the crystallographic orientation relationship. zirconium-to-hydride grain orientation follows Shoji-Nishiyama crystallographic relationship. This relationship is stable before and after creep deformation. These results of creep performance and texture stability of Zircaloy-4 claddings can help support the design basis of interim and long-term dry storage facilities.

creep↗
DOE OSTI2022

Entropy and crystal-facet modulation of P2-type layered cathodes for long-lasting sodium-based batteries

Abstract P2-type sodium manganese-rich layered oxides are promising cathode candidates for sodium-based batteries because of their appealing cost-effective and capacity features. However, the structural distortion and cationic rearrangement induced by irreversible phase transition and anionic redox reaction at high cell voltage (i.e., >4.0 V) cause sluggish Na-ion kinetics and severe capacity decay. To circumvent these issues, here, we report a strategy to develop P2-type layered cathodes via configurational entropy and ion-diffusion structural tuning. In situ synchrotron X-ray diffraction combined with electrochemical kinetic tests and microstructural characterizations reveal that the entropy-tuned Na 0.62 Mn 0.67 Ni 0.23 Cu 0.05 Mg 0.07 Ti 0.01 O 2 (CuMgTi-571) cathode possesses more {010} active facet, improved structural and thermal stability and faster anionic redox kinetics compared to Na 0.62 Mn 0.67 Ni 0.37 O 2 . When tested in combination with a Na metal anode and a non-aqueous NaClO 4 -based electrolyte solution in coin cell configuration, the CuMgTi-571-based positive electrode enables an 87% capacity retention after 500 cycles at 120 mA g −1 and about 75% capacity retention after 2000 cycles at 1.2 A g −1 .

25 ENERGY STORAGE↗
DOE OSTI2022

Dislocation loop evolution in Kr-irradiated ThO 2

Here, the early stage of microstructural evolution of ThO 2 , under krypton irradiation at 600, 800, and 1000°C, was investigated using in situ transmission electron microscopy (TEM). Dislocation loops grew faster, whereas their number density decreased with increasing irradiation temperature. Loop density was found to decrease with ion dose. Interstitial dislocation loops, including Frank loops with Burgers vector of $\textit{a}/3\langle111\rangle$ and perfect loops with Burgers vector of $\textit{a}/2\langle110\rangle$, were determined by traditional TEM and atomic resolution–scanning TEM techniques. Atomistic and mesoscale level modeling are performed to interpret experimental observations. The migration energy barriers of defects in ThO 2 were calculated using density-functional theory. The energetics of different dislocation loop types were studied using molecular dynamics simulations. Loop density and diameter were analyzed using a kinetic rate theory model that considers stoichiometric loop evolution. This analysis reveals that loop growth is governed by the mobility of cation interstitials, whereas loop nucleation is determined by the mobility of anion defects. Lastly, a rate theory model was used to extract the diffusion coefficients of thorium interstitials, oxygen interstitials, and vacancies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Native lattice strain induced structural earthquake in sodium layered oxide cathodes

Abstract High-voltage operation is essential for the energy and power densities of battery cathode materials, but its stabilization remains a universal challenge. To date, the degradation origin has been mostly attributed to cycling-initiated structural deformation while the effect of native crystallographic defects induced during the sophisticated synthesis process has been significantly overlooked. Here, using in situ synchrotron X-ray probes and advanced transmission electron microscopy to probe the solid-state synthesis and charge/discharge process of sodium layered oxide cathodes, we reveal that quenching-induced native lattice strain plays an overwhelming role in the catastrophic capacity degradation of sodium layered cathodes, which runs counter to conventional perception—phase transition and cathode interfacial reactions. We observe that the spontaneous relaxation of native lattice strain is responsible for the structural earthquake (e.g., dislocation, stacking faults and fragmentation) of sodium layered cathodes during cycling, which is unexpectedly not regulated by the voltage window but is strongly coupled with charge/discharge temperature and rate. Our findings resolve the controversial understanding on the degradation origin of cathode materials and highlight the importance of eliminating intrinsic crystallographic defects to guarantee superior cycling stability at high voltages.

25 ENERGY STORAGE↗