Engineering topics

Liu, Ming

Publications and source records attributed to Liu, Ming.

5 records

DOE OSTI2024

Stabilizing LiCoO 2 at 4.6 V by regulating anti-oxidative solvents

For LiCoO 2 (LCO) operating at high voltages (>4.5 V vs. Li/Li + ), the intensive side reactions between LCO and traditional ethylene carbonate (EC)-based electrolytes with LiPF 6 salts can produce plenty of corrosive species (such as HF and HPO 2 F 2 ), causing severe surface degradation. Herein, anti-oxidative fluoroethylene carbonate (FEC) and difluoroethylene carbonate (DFEC) were selected as co-solvents to reduce the generation of corrosive species. Besides, PF 6 − anions enrich the Helmholtz plane of the LCO/electrolyte interface and promote the formation of a robust cathode/electrolyte interphase (CEI) featuring LiF/Li x PO y F z /Li 3 PO 4 inorganics and P-containing organics under the synergy of fluorinated solvents, which significantly inhibits the catalysis of highly oxidative Co 4+ /O n− (0 < n < 2). Benefiting from the reduced corrosive species and reinforced CEI, the layered structure of the LCO surface is well preserved during long-term cycling, with a highly reversible O3/H1-3 phase transition. Consequently, a LCO||graphite pouch cell exhibits a remarkable capacity retention of 85.7% after 500 cycles in 3.0–4.55 V. Furthermore, this work provides a new insight into developing advanced functional electrolytes for high-voltage lithium-ion batteries.

Co/O loss↗

DOE OSTI2024

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO 2 at 4.65 V

For LiCoO 2 (LCO) operated beyond 4.55 V (vs Li/Li + ), it usually suffers from severe surface degradation. Constructing a robust cathode/electrolyte interphase (CEI) is effective to alleviate the above issues, however, the correlated mechanisms still remain vague. Herein, a progressively reinforced CEI is realized via constructing Zr-O deposits (ZrO 2 and Li 2 ZrO 3 ) on LCO surface (i.e., Z-LCO). Upon cycle, these Zr-O deposits can promote the decomposition of LiPF6, and progressively convert to the highly dispersed Zr-O-F species. In particular, the chemical reaction between LiF and Zr-O-F species further leads to the densification of CEI, which greatly reinforces its toughness and conductivity. Further, combining the robust CEI and thin surface rock-salt layer of Z-LCO, several benefits are achieved, including stabilizing the surface lattice oxygen, facilitating the interface Li + transport kinetics, and enhancing the reversibility of O3/H1-3 phase transition, etc. As a result, the Z-LCO||Li cells exhibit a high capacity retention of 84.2% after 1000 cycles in 3–4.65 V, 80.9% after 1500 cycles in 3–4.6 V, and a high rate capacity of 160 mAh g -1 at 16 C (1 C = 200 mA g -1 ). This work provides a new insight for developing advanced LCO cathodes.

25 ENERGY STORAGE↗

DOE OSTI2023

Ion and Hydrodynamic Translucency in 1D van der Waals Heterostructured Boron-Nitride Single-Walled Carbon Nanotubes

An unresolved challenge in nanofluidics is tuning ion selectivity and hydrodynamic transport in pores, particularly for those with diameters larger than a nanometer. In contrast to conventional strategies that focus on changing surface functionalization or confinement degree by varying the radial dimension of the pores, we explore a unique approach for manipulating ion selectivity and hydrodynamic flow enhancement by externally coating single-walled carbon nanotubes (SWCNTs) with a few layers of hexagonal boron nitride (h-BN). Here, for van der Waals heterostructured BN-SWCNTs, we observed a 9-fold increase in cation selectivity for K + versus Cl – compared to pristine SWCNTs of the same 2.2 nm diameter, while hydrodynamic slip lengths decreased by more than an order of magnitude. These results suggest that the single-layer graphene inner surface may be translucent to charge-regulation and hydrodynamic-slip effects arising from h-BN on the outside of the SWCNT. Such 1D heterostructures could serve as synthetic platforms with tunable properties for exploring distinct nanofluidic phenomena and their potential applications.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Irradiation of ultrasonic sensors and adhesive couplants for application in light water reactor primary loop piping and components

The Electric Power Research Institute (EPRI) Nuclear Sector and US Department of Energy Light Water Reactor Sustainability Program are committed to engaging in research and development endeavors to address materials aging issues specific to long term operation of light water power reactors. To this effect, EPRI launched an industry initiative to develop nondestructive evaluation systems for online monitoring of existing cracks in light water reactor primary coolant loop piping and components. One of the goals of this initiative is to develop a sensor system (or systems) that can determine nondestructively if cracks are growing or arrested and, in the case of the former, to characterize their growth rates. A missing component of this initiative is an experimental assessment of how sensors and adhesive couplants will perform in service when exposed to chronic energetic neutron radiation, particularly at the primary coolant loop hot and cold leg dissimilar metal welds, which join the primary loop piping to the reactor pressure vessel and reside in the vicinity of the reactor core. The objective of this experimental study was to determine how ultrasonic transducers and adhesive couplants perform when exposed to irradiation in a test reactor to simulate and accelerate in-service exposure. Further, to achieve this objective, the signal stability of piezoelectric transducers and performance of adhesive couplants as a function of accumulated fast neutron fluence were characterized by collecting ultrasonic data in-situ during irradiation. Of particular interest were the ultrasonic signal quality and time decay of the amplitude of acoustic reflections as a function of fast neutron fluence. The results of the study showed that, of the 8 transducer/substrate sample assemblies tested, only 3 generated usable ultrasonic signals through the conclusion of the irradiation campaign. It was found that high temperature epoxy tends to ultrasonically couple the sensors to the substrates better than three types of refractory ceramic cements studied, as is supported by post irradiation examination. The results obtained through this experimental study will be utilized in the achievement of the overall goal of development of a sensor system to perform online monitoring of primary loop components.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1998

A New and Fast Method for Smoothing Spectral Imaging Data

The Airborne Visible Infrared Imaging Spectrometer (AVIRIS) acquires spectral imaging data covering the 0.4 - 2.5 micron wavelength range in 224 10-nm-wide channels from a NASA ER-2 aircraft at 20 km. More than half of the spectral region is affected by atmospheric gaseous absorption. Over the past decade, several techniques have been used to remove atmospheric effects from AVIRIS data for the derivation of surface reflectance spectra. An operational atmosphere removal algorithm (ATREM), which is based on theoretical modeling of atmospheric absorption and scattering effects, has been developed and updated for deriving surface reflectance spectra from AVIRIS data. Due to small errors in assumed wavelengths and errors in line parameters compiled on the HITRAN database, small spikes (particularly near the centers of the 0.94- and 1.14-micron water vapor bands) are present in this spectrum. Similar small spikes are systematically present in entire ATREM output cubes. These spikes have distracted geologists who are interested in studying surface mineral features. A method based on the "global" fitting of spectra with low order polynomials or other functions for removing these weak spikes has recently been developed by Boardman (this volume). In this paper, we describe another technique, which fits spectra "locally" based on cubic spline smoothing, for quick post processing of ATREM apparent reflectance spectra derived from AVIRIS data. Results from our analysis of AVIRIS data acquired over Cuprite mining district in Nevada in June of 1995 are given. Comparisons between our smoothed spectra and those derived with the empirical line method are presented.

Gao, Bo-Cai↗