Engineering Papers⌕ Search

Engineering topics

Liu, Jun

Publications and source records attributed to Liu, Jun.

At least 703 records · Page 39

A fundamental study on the [(μ-Cl) 3 Mg 2 (THF) 6 ] + dimer electrolytes for rechargeable Mg batteries

We present a fundamental study on [(μ-Cl) 3 Mg 2 (THF) 6 ] + dimer electrolytes using various physical methods including Subambient Pressure Ionization with Nanoelectrospray Mass spectrometry (SPIN-MS), Raman spectroscopy, 25 Mg{ 1 H} NMR, 27 Al{ 1 H} NMR and electrochemical analysis. For the first time, long time sought THF solvated [MgCl] + species was experimentally characterized by SPIN mass spectrometry in the solution of the Mgdimer containing electrolyte, confirming the mono-Cl- abstraction reaction between MgCl 2 and an Al Lewis acid. Solvated MgCl 2 in the electrolyte was confirmed by Raman spectroscopy. The experimental results establish the previously proposed dimerization equilibrium of solvated [MgCl] + and MgCl2 with [(μ-Cl) 3 Mg 2 (THF)6] + . 25 Mg{ 1 H} NMR, 27 Al{ 1 H} NMR and electrochemical analysis on chloration reaction of [(μ-Cl) 3 Mg 2 (THF) 6 ]AlPh 3 Cl with external Cl- led to further insights on the coordination chemistry of the dimer electrolyte. Finally, a comprehensive mechanism is proposed for the reversible electrochemical Mg deposition and stripping and Mg 2+ and Cl- ion transports of the Mg dimer electrolytes in rechargeable Mg batteries.

25 ENERGY STORAGE↗

Hydrophobic pillared square grids for selective removal of CO 2 from simulated flue gas

Capture of CO2 from flue gas is considered to be a feasible approach to mitigate the effects of anthropogenic emission of CO2. Herein we report that an isostructural family of metal organic materials (MOMs) of general formula [M(linker)(2)(pillar)], linker = pyrazine, pillar = hexaflourosilicate and M = Zn, Cu, Ni and Co exhibits highly selective removal of CO2 fromdry and wet simulated flue gas. Two members of the family, M = Ni and Co, SIFSIX-3-Ni and SIFSIX-3-Co, respectively, are reported for the first time and compared with the previously reported Zn and Cu analogs.

Elsaidi, Sameh K.↗

Highly Active Electrolytes for Rechargeable Mg Batteries Based on [Mg2(μ-Cl)2]2+ Cation Complex in Dimethoxyethane

Highly active electrolytes based on a novel [Mg2(μ-Cl)2]2+ cation complex for reversible Mg deposition were developed and analyzed in this work. These electrolytes were formulated in dimethoxyethane through dehalodimerization of non-nucleophilic MgCl2 by reacting with either Mg salts (such as Mg(TFSI)2, TFSI= bis(trifluoromethane)sulfonylimide) or Lewis acid salts (such as AlEtCl2 or AlCl3). The cation complex was identified for the first time as [Mg2(μ-Cl)2(DME)4]2+ (DME=dimethoxyethane) and its molecular structure was characterized by single crystal X-ray diffraction, Raman spectroscopy and NMR. The electrolyte synthesis process was studied and rational approaches for formulating highly active electrolytes were proposed. Through control of the anions, electrolytes with efficiency close to 100%, wide electrochemical window (up to 3.5V) and high ionic conductivity (> 6 mS/cm) were obtained. The electrolyte synthesis and understandings developed in this work could bring significant opportunities for rational formulation of electrolytes with the general formula [Mg2(μ-Cl)2(DME)4][anion]x for practical Mg batteries.

Environmental Molecular Sciences Laboratory↗

Separation of C2 Hydrocarbons by Porous Materials: Metal Organic Frameworks as Platform

The effective separation of small hydrocarbon molecules (C1 – C4) is an important process for petroleum industry, determining the end price of many essential commodities in our daily lives. Current technologies for separation of these molecules rely on energy intensive fractional distillation processes at cryogenic temperature, which is particularly difficult because of their similar volatility. In retrospect, adsorptive separation using solid state adsorbents might be a cost effective alternative. Several types of solid state adsorbents (e.g. zeolite molecular sieves) were tested for separation of small hydrocarbon molecules as a function of pressure, temperature or vacuum. Among different types of plausible adsorbents, metal organic frameworks (MOFs), a class of porous, crystalline, inorganic-organic hybrid materials, is particularly promising. In this brief comment article, we discuss the separation properties of different types of solid state adsorbents, with a particular emphasis on MOF based adsorbents for separation of C2 hydrocarbon molecules.

Banerjee, Debasis↗

Measurement of the anisotropic thermal conductivity of molybdenum disulfide by the time-resolved magneto-optic Kerr effect

We use pump-probe metrology based on the magneto-optic Kerr effect to measure the anisotropic thermal conductivity of (001)-oriented MoS{sub 2} crystals. A ≈20 nm thick CoPt multilayer with perpendicular magnetization serves as the heater and thermometer in the experiment. The low thermal conductivity and small thickness of the CoPt transducer improve the sensitivity of the measurement to lateral heat flow in the MoS{sub 2} crystal. The thermal conductivity of MoS{sub 2} is highly anisotropic with basal-plane thermal conductivity varying between 85–110 W m{sup -1} K{sup -1} as a function of laser spot size. The basal-plane thermal conductivity is a factor of ≈50 larger than the c-axis thermal conductivity, 2.0±0.3 W m{sup -1} K{sup -1}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Equation of State for the Thermodynamic Properties of Cyclohexane

An equation of state for cyclohexane has been developed using the Helmholtz energy as the fundamental property with independent variables of density and temperature. Multi-property fitting technology was used to fit the equation of state to data for pρT, heat capacities, sound speeds, virial coefficients, vapor pressures, and saturated densities. The equation of state was developed to conform to the Maxwell criteria for two-phase vapor-liquid equilibrium states, and is valid from the triple-point temperature to 700 K, with pressures up to 250 MPa and densities up to 10.3 mol dm{sup −3}. In general, the uncertainties (k = 2, indicating a level of confidence of 95%) in density for the equation of state are 0.1% (liquid and vapor) up to 500 K, and 0.2% above 500 K, with higher uncertainties within the critical region. Between 283 and 473 K with pressures lower than 30 MPa, the uncertainty is as low as 0.03% in density in the liquid phase. The uncertainties in the speed of sound are 0.2% between 283 and 323 K in the liquid, and 1% elsewhere. Other uncertainties are 0.05% in vapor pressure and 2% in heat capacities. The behavior of the equation of state is reasonable within the region of validity and at higher and lower temperatures and pressures. A detailed analysis has been performed in this article.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ecological roles of dominant and rare prokaryotes in acid mine drainage revealed by metagenomics and metatranscriptomics

Here we report that high-throughput sequencing is expanding our knowledge of microbial diversity in the environment. Still, understanding the metabolic potentials and ecological roles of rare and uncultured microbes in natural communities remains a major challenge. To this end, we applied a ‘divide and conquer’ strategy that partitioned a massive metagenomic data set (>100 Gbp) into subsets based on K-mer frequency in sequence assembly to a low-diversity acid mine drainage (AMD) microbial community and, by integrating with an additional metatranscriptomic assembly, successfully obtained 11 draft genomes most of which represent yet uncultured and/or rare taxa (relative abundance <1%). We report the first genome of a naturally occurring Ferrovum population (relative abundance >90%) and its metabolic potentials and gene expression profile, providing initial molecular insights into the ecological role of these lesser known, but potentially important, microorganisms in the AMD environment. Gene transcriptional analysis of the active taxa revealed major metabolic capabilities executed in situ, including carbon- and nitrogen-related metabolisms associated with syntrophic interactions, iron and sulfur oxidation, which are key in energy conservation and AMD generation, and the mechanisms of adaptation and response to the environmental stresses (heavy metals, low pH and oxidative stress). Remarkably, nitrogen fixation and sulfur oxidation were performed by the rare taxa, indicating their critical roles in the overall functioning and assembly of the AMD community. Finally, our study demonstrates the potential of the ‘divide and conquer’ strategy in high-throughput sequencing data assembly for genome reconstruction and functional partitioning analysis of both dominant and rare species in natural microbial assemblages.

59 BASIC BIOLOGICAL SCIENCES↗

Pump-probe measurements of the thermal conductivity tensor for materials lacking in-plane symmetry

We previously demonstrated an extension of time-domain thermoreflectance (TDTR) which utilizes offset pump and probe laser locations to measure in-plane thermal transport properties of multilayers. However, the technique was limited to systems of transversely isotropic materials studied using axisymmetric laser intensities. Here, we extend the mathematics so that data reduction can be performed on non-transversely isotropic systems. An analytic solution of the diffusion equation for an N-layer system is given, where each layer has a homogenous but otherwise arbitrary thermal conductivity tensor and the illuminating spots have arbitrary intensity profiles. As a demonstration, we use both TDTR and time-resolved magneto-optic Kerr effect measurements to obtain thermal conductivity tensor elements of <110> α-SiO{sub 2}. We show that the out-of-phase beam offset sweep has full-width half-maxima that contains nearly independent sensitivity to the in-plane thermal conductivity corresponding to the scanning direction. Also, we demonstrate a Nb-V alloy as a low thermal conductivity TDTR transducer layer that helps improve the accuracy of in-plane measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Charging Graphene for Energy Storage

Since 2004, graphene, including single atomic layer graphite sheet, and chemically derived graphene sheets, has captured the imagination of researchers for energy storage because of the extremely high surface area (2630 m2/g) compared to traditional activated carbon (typically below 1500 m2/g), excellent electrical conductivity, high mechanical strength, and potential for low cost manufacturing. These properties are very desirable for achieving high activity, high capacity and energy density, and fast charge and discharge. Chemically derived graphene sheets are prepared by oxidation and reduction of graphite1 and are more suitable for energy storage because they can be made in large quantities. They still contain multiply stacked graphene sheets, structural defects such as vacancies, and oxygen containing functional groups. In the literature they are also called reduced graphene oxide, or functionalized graphene sheets, but in this article they are all referred to as graphene for easy of discussion. Two important applications, batteries and electrochemical capacitors, have been widely investigated. In a battery material, the redox reaction occurs at a constant potential (voltage) and the energy is stored in the bulk. Therefore, the energy density is high (more than 100 Wh/kg), but it is difficult to rapidly charge or discharge (low power, less than 1 kW/kg)2. In an electrochemical capacitor (also called supercapacitors or ultracapacitor in the literature), the energy is stored as absorbed ionic species at the interface between the high surface area carbon and the electrolyte, and the potential is a continuous function of the state-of-charge. The charge and discharge can happen rapidly (high power, up to 10 kW/kg) but the energy density is low, less than 10 Wh/kg2. A device that can have both high energy and high power would be ideal.

energy density↗

Self assembled multi-layer nanocomposite of graphene and metal oxide materials

Nanocomposite materials having at least two layers, each layer consisting of one metal oxide bonded to at least one graphene layer were developed. The nanocomposite materials will typically have many alternating layers of metal oxides and graphene layers, bonded in a sandwich type construction and will be incorporated into an electrochemical or energy storage device.

36 MATERIALS SCIENCE↗

A general mechanism for stabilizing the small sizes of precious metal nanoparticles on oxide supports

We recently discovered that MgAl2O4 spinel {111} nano-facets optimally stabilize the small sizes of platinum nanoparticles even after severe high temperature aging treatments. Here we report the thermal stabilities of other precious metals with various physical and chemical properties on the MgAl2O4 spinel {111} facets, providing important new insights into the stabilization mechanisms. Besides Pt, Rh and Ir can also be successfully stabilized as small (1-3 nm) nanoparticles and even as single atomic species after extremely severe (800 °C, 1 week) oxidative aging. However, other metals either aggregate (Ru, Pd, Ag, and Au) or sublimate (Os) even during initial catalyst synthesis. On the basis of ab initio theoretical calculations and experimental observations, we rationalize that the exceptional stabilization originates from lattice matching, and the correspondingly strong attractive interactions at interfaces between the spinel {111} surface oxygens and epitaxial metals\metal oxides. On this basis, design principles for catalyst support oxide materials that are capable in stabilizing precious metals are proposed.

anti-sintering↗

Facile Synthesis of Chevrel Phase Nanocubes and their Applications for Multivalent Energy Storage

The Chevrel phases (CPs, MxMo6T8, M=metal, T=S or Se) are capable of rapid and reversible intercalation of multivalent ions and are the most practical cathode materials for rechargeable magnesium batteries. For the first time, we report a facile method for synthesizing Mo6S8 nanoparticles and demonstrate that these nanoparticles have significantly better Mg2+ intercalation kinetics compared with microparticles. The results described in this work could inspire the synthesis of nanoscale CPs, which could substantially impact their application.

Chevrel phase↗

Liquid-Metal Electrode to Enable Ultra-Low Temperature Sodium-Beta Alumina Batteries for Renewable Energy Storage

Metal electrodes have a high capacity for energy storage but have found limited applications in batteries because of dendrite formation and other problems. In this paper, we report a new alloying strategy that can significantly reduce the melting temperature and improve wetting with the electrolyte to allow the use of liquid metal as anode in sodium-beta alumina batteries (NBBs) at much lower temperatures (e.g., 95 to 175°C). Commercial NBBs such as sodium-sulfur (Na-S) battery and sodium-metal halide (ZEBRA) batteries typically operate at relatively high temperatures (e.g., 300-350°C) due to poor wettability of sodium on the surface of β"-Al2O3. Our combined experimental and computational studies suggest that Na-Cs alloy can replace pure sodium as the anode material, which provides a significant improvement in wettability, particularly at lower temperatures (i.e., <200°C). Single cells with the Na-Cs alloy anode exhibit excellent cycling life over those with pure sodium anode at 175 and 150°C. The cells can even operate at 95°C, which is below the melting temperature of pure sodium. These results demonstrate that NBB can be operated at ultra lower temperatures with successfully solving the wetting issue. This work also suggests a new strategy to use liquid metal as the electrode materials for advanced batteries that can avoid the intrinsic safety issues associated with dendrite formation on the anode.

Lu, Xiaochuan↗

Mesoporous Silicon Sponge as an Anti-Pulverization Structure for High-Performance Lithium-ion Battery Anodes

Nanostructured silicon is a promising anode material for high performance lithium-ion batteries, yet scalable synthesis of such materials, and retaining good cycling stability in high loading electrode remain significant challenges. Here, we combine in-situ transmission electron microscopy and continuum media mechanical calculations to demonstrate that large (>20 micron) mesoporous silicon sponge (MSS) prepared by the scalable anodization method can eliminate the pulverization of the conventional bulk silicon and limit particle volume expansion at full lithiation to ~30% instead of ~300% as observed in bulk silicon particles. The MSS can deliver a capacity of ~750 mAh/g based on the total electrode weight with >80% capacity retention over 1000 cycles. The first-cycle irreversible capacity loss of pre-lithiated MSS based anode is only <5%. The insight obtained from MSS also provides guidance for the design of other materials that may experience large volume variation during operations.

anode↗

High-energy metal air batteries

Disclosed herein are embodiments of lithium/air batteries and methods of making and using the same. Certain embodiments are pouch-cell batteries encased within an oxygen-permeable membrane packaging material that is less than 2% of the total battery weight. Some embodiments include a hybrid air electrode comprising carbon and an ion insertion material, wherein the mass ratio of ion insertion material to carbon is 0.2 to 0.8. The air electrode may include hydrophobic, porous fibers. In particular embodiments, the air electrode is soaked with an electrolyte comprising one or more solvents including dimethyl ether, and the dimethyl ether subsequently is evacuated from the soaked electrode. In other embodiments, the electrolyte comprises 10-20% crown ether by weight.

25 ENERGY STORAGE↗